On the Prediction of Biogas Production from Vegetables, Fruits, and Food Wastes by ANFIS- and LSSVM-Based Models

Yang, Yong; Zheng, Shuaishuai; Ai, Zhilu; Jafari, Mohammad Mahdi Molla

doi:https://doi.org/10.1155/2021/9202127

BioMed Research International

On this page

Abstract Introduction Materials and Methods Results and Discussion Conclusions Data Availability Conflicts of Interest Acknowledgments References Copyright Related Articles

Special Issue

Application of Intelligence Methods in Biosciences

View this Special Issue

Research Article | Open Access

Volume 2021 | Article ID 9202127 | https://doi.org/10.1155/2021/9202127

On the Prediction of Biogas Production from Vegetables, Fruits, and Food Wastes by ANFIS- and LSSVM-Based Models

Yong Yang,^1,2Shuaishuai Zheng,^1,2Zhilu Ai ,^1,2and Mohammad Mahdi Molla Jafari³

Academic Editor: Alireza Baghban

Received05 Aug 2021

Revised17 Aug 2021

Accepted21 Aug 2021

Published24 Sept 2021

Abstract

This study is aimed at modeling biodigestion systems as a function of the most influencing parameters to generate two robust algorithms on the basis of the machine learning algorithms, including adaptive network-based fuzzy inference system (ANFIS) and least square support vector machine (LSSVM). The models are assessed utilizing multiple statistical analyses for the actual values and model outcomes. Results from the suggested models indicate their great capability of predicting biogas production from vegetable food, fruits, and wastes for a variety of ranges of input parameters. The values that are calculated for the mean relative error (MRE %) and mean squared error (MSE) were 29.318 and 0.0039 for ANFIS, and 2.951 and 0.0001 for LSSVM which shows that the latter model has a better ability to predict the target data. Finally, in order to have additional certainty, two analyses of outlier identification and sensitivity were performed on the input parameter data that proved the proposed model in this paper has higher reliability in assessing output values compared with the previous model.

1. Introduction

The main disposal pathways for FW (food waste) residues are treating via incineration or disposal in landfills. Given the very fast biodegradability of the food wastes in the presence of contaminating microorganisms, their disposal in landfills is very problematic [1, 2]. In addition, biodegradation within landfills necessitates a vast area, and greenhouse gases, e.g., methane, are generated with no profit gained via the energy produced through the biomass [3]. Thus, many nations have prohibited such a disposal option. From another viewpoint, given the high moisture content (>70%) of the organic matter, the incineration requires intensive amounts of energy with no energy recovery in some situations [4, 5]. Both options impose adverse impacts on human health and the environment [6, 7].

Therefore, since waste-to-energy techniques support reduced environmental impacts and partial replacement of fossil reserves, they are studied for disposal of organic wastes. One of the feasible approaches is AD (anaerobic digestion), which is an environmentally friendly technology for transforming liquid or solid organic wastes into biogas, which is convertible to beneficial energies (heat and/or electricity) [8, 9]. Anaerobic digestion is a complicated multistep biochemical degradation procedure conducted in the absence of O₂, through which the microorganisms transform organic compounds into a gaseous mix mainly composed of CO₂ (carbon dioxide), N₂ (nitrogen), and CH₄ (methane). Nonetheless, one can find other compounds in the composition, including H₂ (hydrogen), H₂S (hydrogen sulfide), O₂ (oxygen), CO (carbon monoxide), and NH₃ (ammonia). Also, trace amounts of siloxanes, dust particles, and halogenated and aromatic compounds are found in biogas; some of which can increase emissions, corrosion, and biohazards for human health. Biogas is also saturated with water. Also, this process generates sludge residues (or digests), which can be utilized as a fuel for energy generation subsequent to a drying treatment or directly for remediation of soil [10].

The conversion yield, the biogas composition, and the production rate are affected by the biomass nature, the configuration of biodigester, and the process characteristics [11, 12]. Given the diversity of handling and processing techniques, resources, local seasons and climates, and eating behaviors, the same kind of FWs may provide extremely variable features [13]. The amount of TSs (total solids) found in FW ranges from <2%w in liquid FWs to >90%w in solid FWs. The organic content (often ~90%) shown by the VS/TS ratio (in which the VS (volatile solids) represents the weight fraction convertible into gaseous materials) makes biomass a suitable candidate for anaerobic digestion. The C/N ratio varies between 3 and 55, paving the way for modifying the mixture C/N ratio to reach the optimum biodegradability for the food biomass. For most of the FWs, the acidity necessitates adding chemicals (e.g., alkali reagents) to stabilize biodigesters’ pH. For each kind of FWs, the highest potential of methane production is within the 0.31–1.1 m³ CH₄/kg range when volatile solids are added [14]. Thus, the electricity generated per 1 ton of fresh substances is within the 151.6-224.6 m³/t range for FVW and FW, which is nearly the same value acquired from chicken and cattle dungs (257.3 and 122.5 m³/t, respectively) [15].

As observed in [16–18] and others, the parameters contributing to biogas generation have been investigated. Nonetheless, only a few studies have simultaneously investigated more than a single factor. The simultaneous investigation of the interacting impact of a number of experimental scenarios presents invaluable data for optimization and prediction of the key features used in the experimental procedure of the entire studied scenarios. The problem is finding plausible standard experimental techniques for dataset compilation. Concerning optimization and prediction, the most routine methods pave the way for creating polynomial models correlating the response to the procedure irrespective of variables and their associated interactions [19]. Seman et al. concentrated on developing an association between parameters and evaluating the interactions between factors [20]. Therefore, the parameter optimization and response prediction of the process were founded on the basis of polynomial regression modeling (second-order model).

Another modeling instrument employed for better prediction is ANNs (artificial neural networks) [21]. The independent variables employed by Beltramo et al. in the artificial neural network model to assess the rate of biogas generation were TS, VFA, VS, acid detergent lignin, acid detergent fiber, ammonium nitrogen, neutral detergent fiber, OLR, and HRT [22]. The prediction error of the model was 6.24%, and the authors considered a coefficient of determination, , as the optimum result. By using an artificial neural network, Ghatak et al. optimized and modeled the prediction of particular biogas generation via the parameters including temperature, duration, and composition [23]. The neural model could anticipate the creation of biogas with an accuracy of 99.7%.

In this paper, we have tried to predict the values of biogas production from vegetables, fruits, and food wastes using two new models, ANFIS and LSSVM. First, a wide range of actual output data and input parameters affecting them were collected. Then, these two models were constructed and statistically evaluated, and compared. Finally, the results of these models were compared with the previously proposed models (in terms of accuracy), and the best model was proposed.

2. Description of Models

2.1. ANFIS

The adaptive network-based fuzzy inference system (ANFIS) algorithm is defined as a class of neural network techniques to address problems involving function approximation [24]. To put it in another way, an ANFIS structure is a combined information acquired from the fuzzy logic system and artificial neural network, and it consists of several membership function (MF) parameters optimized utilizing optimization algorithms [25]. Accordingly, the ANFIS structure, because of being particular, is significantly precise, and its reliance on real values is less than other machine learning algorithms, for instance, the artificial neural networks [25].

A typical ANFIS structure includes five layers, each of which has a number of nodes defined by their node functions [26]. Layers’ association can be established using internal connections. The outputs of the previous layer are used as the inputs of the next layer. It is worth noting that the fuzzy inference system is utilized in the ANFIS technique as a fuzzy system. More specifically, for the inputs with two parameters, and , and output with a single parameter, , the rules governing an ANFIS structure are expressed as follows [27].

First rule: if is and is then is

where fuzzy sets indicated by and and () is representative of the first-order fuzzy inference system output.

The adaptive nodes included in the first layer are specified as follows:

where and indicate the membership functions.

Each node denoted by is constant in the following layer. where indicates the firing strength of the rule.

The third layer has constant nodes denoted by . The corresponding node functions are applied to normalize the firing by dividing the ^th node’s firing strength value by the all firing strength values’ summation [28].

The fourth layer includes adaptive nodes indicated by the square shapes. where and indicate the fuzzy if-then rules defined as follows [29].

Rule 1: if is and is then =

where , , and indicate the consequential terms.

The overall output in the last layer is given by:

Totally, the output is described as a linear combined consequential term [30].

2.2. LSSVM

The supervised least square support vector machine (LSSVM) algorithm developed in 1999 by Suykens et al. for solving problems stemmed from the regression together with function approximation. For the inputs denoted by and the output denoted by , the usual LSSVM nonlinear function is given as follows [31]. where indicates the connections between the target output and inputs, denotes the -dimensional weight vector, and denotes the bias. The following equation is commonly used to solve the regression problems concerning the minimization theory [32]:

The following boundary conditions need to be considered: where indicates the margin parameter and indicates the error variable of . The LSSVM straightforward derivations lead to

The radial basis function is commonly used as a kernel function in regression faults due to its great efficiency, which is given by [33]

The in this equation indicates the squared bandwidth that needs to be estimated using optimization.

3. Materials and Methods

3.1. Sensitivity Analysis

In order to analyze the effects of individual inputs on the output value, a sensitivity analysis was carried out. Thus, the relevancy factor was decided as presented in the following to discover the effect of the individual inputs [34].

In this equation, and stand for the average of the input, and the average of the _th output, represents the _th output, represents the entire number of data points, and stands for the _th input value of the _th parameter. Also, the values range between -1 and 1. The less absolute value is interpreted as the fact that the input is less effective on the output parameter. In addition, the positivity or negativity of is regarded as direct or reverse impacts of the concerned inputs; i.e., by increasing an input with negative values, the target parameter is decreased; however, for the inputs with negative values of , it is increased.

This research examined eight inputs that reflected a direct impact on the discussed target. Figure 1 presents the analysis results, where the highest eigenvalue is of the positive value of that refers to HRT (d).

3.2. Data Gathering and Preanalysis Phase

In this phase, our study employed two different techniques to evaluate and predict the output parameters from the employed algorithms. Then, the data acquired in the experiments conducted in this research were employed for training the above-mentioned algorithms [35], whilst of the whole data points, about 25% of the same data points were used for the validation of those algorithms. Also, the dataset was subjected to the normalization procedure:

In the above equation, represents the normalized value and stands for the input value.

3.3. Identification of Outliers

Outlier or suspected data points featuring behaviors that differ from the major part of the databank show up in a large dataset typically. However, the same data points may affect model’s accuracy and reliability. Hence, it seems necessary then to try to find such data in the proposed models, in particular for the training datasets. In case of neglecting some unrecognized impacts, some restrictions may be encountered in the model. In the other words, the analysis of outliers may provide us with an insight on the same restrictions, which are the benefits of the discussed analysis. In order to eliminate the outlier data, the leverage technique was used, which requires determining the deviation of the predictive tool from the concerned real data [34, 36]. The deviation which is also termed as standardized crossvalidated residuals creates a Hat matrix, which can be determined on the basis of the equation below in this study: where stands for an matrix. and , respectively, represent the entire number of data points and the input parameters. and -1 are called transpose and inverse operators, respectively. In addition, the equation below was used to explicate a warning leverage value:

The practical region is delineated within and rectangular area. According to the red points observed in Figure 2, only a number of 20 suspected data were discovered amongst the entire dataset.

(a)

(b)

4. Results and Discussion

The two computational techniques developed in this work are ANFIS and LSSVM used to estimate the target values. Upon splitting the dataset into the testing and training datasets, of the whole data points, 75% were employed to make use of the above-mentioned model for determining the outputs. Then, the training process performance is expressible through a comparison made between the real values and the predicted ones in this step. Alternatively, the comparison made in the testing phase presents a better idea about the model’s accuracy in unclear circumstances, which is called model generalization. Figure 3 presents the simultaneous comparison of the experimental and determined targets for the whole models trained in testing and training databanks. Also, as Figure 3 suggests, the calculated constants may include the experimental points featuring plausible performances.

(a)

(b)

Thus, it is evident that the proposed LSSVM model can estimate outputs with higher accuracy. In order to evaluate the usability of the proposed models, various mathematical and graphical techniques were used. In Figure 4, the crossplots or regression are presented exhibiting the capability of the suggested algorithms in estimating the target values. It is clear that the data points are highly concentrated around the bisector line.

(a)

(b)

Figure 5 presents the deviation plots for the ANFIS and LSSVM models and shows the outputs vs. relative deviation for testing and training steps. Most of the determined deviations are found in the vicinity of the zero error line. In addition, the deviations compaction in the LSSVM model is clearer than the other model. The same compaction reflects the accuracy of prediction for this model.

(a)

(b)

Table 1 reports the mathematical indexes determined for the presented models. The higher values of , and also, the lower values of RMSE, MRE, STD, and MSE are observable for the proposed models, reflecting their good capability in estimating the output values.

Also, the models of ANFIS and LSSVM and the rest of the techniques found in the literature to decide the target values, e.g., those presented by the authors such as Neto and colleagues were compared. In 2021, they used the artificial neural network method to predict this parameter [35]. Compared to other models, the LSSVM model with features the most optimal performance. The same comparison reveals that the minimum accuracy is attributable to the ANN model with .

5. Conclusions

In this study, two accurate techniques, i.e., ANFIS and LSSVM, were presented successfully to estimate biogas production. The developed instruments used for estimation may help the scholars in suggesting a new efficient measurement technique. According to the statistical analyses, the LSSVM model can lead to the most accurate results with the best values of STD, RMSE, , MSE, and MRE. Given the above results, compared to the rest of the computational techniques, the LSSVM model presented a superb performance in terms of validity, accuracy, and generalization. Additionally, a sensitivity analysis was conducted in order to reflect the effect of input parameters on the target values which showed that HRT (d) has the greatest effect on the output parameter.

Data Availability

The data used to support the findings of this study are provided within the article.

Conflicts of Interest

The authors declare that they have no conflicts of interest.

Acknowledgments

This work was supported by the National Key R&D Program of China (project number: 2018YFD0400605).

References

P. Viswanath, S. S. Devi, and K. Nand, “Anaerobic digestion of fruit and vegetable processing wastes for biogas production,” Bioresource Technology, vol. 40, no. 1, pp. 43–48, 1992.
View at: Publisher Site | Google Scholar
O. Kuczman, M. V. D. Gueri, S. N. M. de Souza et al., “Food waste anaerobic digestion of a popular restaurant in Southern Brazil,” Journal of Cleaner Production, vol. 196, pp. 382–389, 2018.
View at: Publisher Site | Google Scholar
S. J. Grimberg, D. Hilderbrandt, M. Kinnunen, and S. Rogers, “Anaerobic digestion of food waste through the operation of a mesophilic two- phase pilot scale digester - assessment of variable loadings on system performance,” Bioresource Technology, vol. 178, pp. 226–229, 2015.
View at: Publisher Site | Google Scholar
M. M. V. Leme, M. H. Rocha, E. E. S. Lora, O. J. Venturini, B. M. Lopes, and C. H. Ferreira, “Techno-economic analysis and environmental impact assessment of energy recovery from municipal solid waste (MSW) in Brazil,” Resources, Conservation and Recycling, vol. 87, pp. 8–20, 2014.
View at: Publisher Site | Google Scholar
M. L. N. Carneiro and M. S. P. Gomes, “Energy, exergy, environmental and economic analysis of hybrid waste-to-energy plants,” Energy Conversion and Management, vol. 179, pp. 397–417, 2019.
View at: Publisher Site | Google Scholar
D. Palaniswamy, “Optimising biogas from food waste using a neural network model,” in in Proceedings of the Institution of Civil Engineers-Municipal Engineer, Thomas Telford Ltd, 2017.
View at: Google Scholar
C. Zhang, H. Su, J. Baeyens, and T. Tan, “Reviewing the anaerobic digestion of food waste for biogas production,” Renewable and Sustainable Energy Reviews, vol. 38, pp. 383–392, 2014.
View at: Publisher Site | Google Scholar
C. Mao, Y. Feng, X. Wang, and G. Ren, “Review on research achievements of biogas from anaerobic digestion,” Renewable and Sustainable Energy Reviews, vol. 45, pp. 540–555, 2015.
View at: Publisher Site | Google Scholar
J. Zhang, K. C. Loh, W. Li, J. W. Lim, Y. Dai, and Y. W. Tong, “Three-stage anaerobic digester for food waste,” Applied Energy, vol. 194, pp. 287–295, 2017.
View at: Publisher Site | Google Scholar
E. A. Scano, C. Asquer, A. Pistis, L. Ortu, V. Demontis, and D. Cocco, “Biogas from anaerobic digestion of fruit and vegetable wastes: experimental results on pilot-scale and preliminary performance evaluation of a full-scale power plant,” Energy Conversion and Management, vol. 77, pp. 22–30, 2014.
View at: Publisher Site | Google Scholar
Q. Sun, H. Li, J. Yan, L. Liu, Z. Yu, and X. Yu, “Selection of appropriate biogas upgrading technology-a review of biogas cleaning, upgrading and utilisation,” Renewable and Sustainable Energy Reviews, vol. 51, pp. 521–532, 2015.
View at: Publisher Site | Google Scholar
I. U. Khan, M. H. D. Othman, H. Hashim et al., “Biogas as a renewable energy fuel - a review of biogas upgrading, utilisation and storage,” Energy Conversion and Management, vol. 150, pp. 277–294, 2017.
View at: Publisher Site | Google Scholar
Y. Meng, S. Li, H. Yuan et al., “Evaluating biomethane production from anaerobic mono- and co-digestion of food waste and floatable oil (FO) skimmed from food waste,” Bioresource Technology, vol. 185, pp. 7–13, 2015.
View at: Publisher Site | Google Scholar
F. Xu, Y. Li, X. Ge, L. Yang, and Y. Li, “Anaerobic digestion of food waste - challenges and opportunities,” Bioresource Technology, vol. 247, pp. 1047–1058, 2018.
View at: Publisher Site | Google Scholar
S. Achinas, V. Achinas, and G. J. W. Euverink, “A technological overview of biogas production from biowaste,” Engineering, vol. 3, no. 3, pp. 299–307, 2017.
View at: Publisher Site | Google Scholar
V. V. Nair, H. Dhar, S. Kumar, A. K. Thalla, S. Mukherjee, and J. W. C. Wong, “Artificial neural network based modeling to evaluate methane yield from biogas in a laboratory-scale anaerobic bioreactor,” Bioresource Technology, vol. 217, pp. 90–99, 2016.
View at: Publisher Site | Google Scholar
A. Sharma, N. A. Ansari, A. Pal, Y. Singh, and S. Lalhriatpuia, “Effect of biogas on the performance and emissions of diesel engine fuelled with biodiesel-ethanol blends through response surface methodology approach,” Renewable Energy, vol. 141, pp. 657–668, 2019.
View at: Publisher Site | Google Scholar
M. Safari, R. Abdi, M. Adl, and J. Kafashan, “Optimization of biogas productivity in lab-scale by response surface methodology,” Renewable Energy, vol. 118, pp. 368–375, 2018.
View at: Publisher Site | Google Scholar
P. Tsapekos, B. Khoshnevisan, M. Alvarado-Morales, A. Symeonidis, P. G. Kougias, and I. Angelidaki, “Environmental impacts of biogas production from grass: role of co-digestion and pretreatment at harvesting time,” Applied Energy, vol. 252, p. 113467, 2019.
View at: Publisher Site | Google Scholar
S. Z. A. Seman, I. Idris, A. Abdullah, I. K. Shamsudin, and M. R. Othman, “Optimizing purity and recovery of biogas methane enrichment process in a closed landfill,” Renewable Energy, vol. 131, pp. 1117–1127, 2019.
View at: Publisher Site | Google Scholar
P. Sakiewicz, K. Piotrowski, J. Ober, and J. Karwot, “Innovative artificial neural network approach for integrated biogas - wastewater treatment system modelling: effect of plant operating parameters on process intensification,” Renewable and Sustainable Energy Reviews, vol. 124, p. 109784, 2020.
View at: Publisher Site | Google Scholar
T. Beltramo, M. Klocke, and B. Hitzmann, “Prediction of the biogas production using GA and ACO input features selection method for ANN model,” Information Processing in Agriculture, vol. 6, no. 3, pp. 349–356, 2019.
View at: Publisher Site | Google Scholar
M. D. Ghatak and A. Ghatak, “Artificial neural network model to predict behavior of biogas production curve from mixed lignocellulosic co-substrates,” Fuel, vol. 232, pp. 178–189, 2018.
View at: Publisher Site | Google Scholar
J.-S. R. Jang, C.-T. Sun, and E. Mizutani, “Neuro-fuzzy and soft computing-a computational approach to learning and machine intelligence [book review],” IEEE Transactions on Automatic Control, vol. 42, no. 10, pp. 1482–1484, 1997.
View at: Publisher Site | Google Scholar
A. Baghban, J. Sasanipour, P. Haratipour, M. Alizad, and M. Vafaee Ayouri, “ANFIS modeling of rhamnolipid breakthrough curves on activated carbon,” Chemical Engineering Research and Design, vol. 126, pp. 67–75, 2017.
View at: Publisher Site | Google Scholar
M. Mir, M. Kamyab, M. J. Lariche, A. Bemani, and A. Baghban, “Applying ANFIS-PSO algorithm as a novel accurate approach for prediction of gas density,” Petroleum Science and Technology, vol. 36, no. 12, pp. 820–826, 2018.
View at: Publisher Site | Google Scholar
A. Baghban, A. Jalali, M. Shafiee, M. H. Ahmadi, and K. W. Chau, “Developing an ANFIS-based swarm concept model for estimating the relative viscosity of nanofluids,” Engineering Applications of Computational Fluid Mechanics, vol. 13, no. 1, pp. 26–39, 2019.
View at: Publisher Site | Google Scholar
S. Shamshirband, M. Hadipoor, A. Baghban, A. Mosavi, J. Bukor, and A. Várkonyi-Kóczy, “Developing an ANFIS-PSO model to predict mercury emissions in combustion flue gases,” Mathematics, vol. 7, no. 10, p. 965, 2019.
View at: Publisher Site | Google Scholar
M. S. Zaghloul, R. A. Hamza, O. T. Iorhemen, and J. H. Tay, “Comparison of adaptive neuro-fuzzy inference systems (ANFIS) and support vector regression (SVR) for data-driven modelling of aerobic granular sludge reactors,” Journal of Environmental Chemical Engineering, vol. 8, no. 3, p. 103742, 2020.
View at: Publisher Site | Google Scholar
Z. X. Li, F. L. Renault, A. O. C. Gómez et al., “Nanofluids as secondary fluid in the refrigeration system: experimental data, regression, ANFIS, and NN modeling,” International Journal of Heat and Mass Transfer, vol. 144, p. 118635, 2019.
View at: Publisher Site | Google Scholar
J. A. Suykens, Least squares support vector machines, World scientific, 2002.
J. Ye and T. Xiong, SVM versus least squares SVM, In Artificial Intelligence and Statistics, PMLR, 2007.
X. Zhang and Z. Ge, “Local parameter optimization of LSSVM for industrial soft sensing with big data and cloud implementation,” IEEE Transactions on Industrial Informatics, vol. 16, no. 5, pp. 2917–2928, 2019.
View at: Publisher Site | Google Scholar
M. H. Ahmadi, A. Baghban, M. Sadeghzadeh et al., “Evaluation of electrical efficiency of photovoltaic thermal solar collector,” Engineering Applications of Computational Fluid Mechanics, vol. 14, no. 1, pp. 545–565, 2020.
View at: Publisher Site | Google Scholar
J. G. Neto, L. V. Ozorio, T. C. C. de Abreu, B. F. dos Santos, and F. Pradelle, “Modeling of biogas production from food, fruits and vegetables wastes using artificial neural network (ANN),” Fuel, vol. 285, p. 119081, 2021.
View at: Publisher Site | Google Scholar
A. Bemani, A. Baghban, and A. H. Mohammadi, “An insight into the modeling of sulfur content of sour gases in supercritical region,” Journal of Petroleum Science and Engineering, vol. 184, p. 106459, 2020.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2021 Yong Yang et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

1633

Downloads

1105

Citations