Table of Contents Author Guidelines Submit a Manuscript
Geofluids
Volume 2017 (2017), Article ID 8916313, 9 pages
https://doi.org/10.1155/2017/8916313
Research Article

Computational Flow Dynamic Simulation of Micro Flow Field Characteristics Drainage Device Used in the Process of Oil-Water Separation

Department of Power Engineering, School of Energy, Power & Mechanical Engineering, North China Electric Power University, Baoding, Hebei 071003, China

Correspondence should be addressed to Zhijian Liu

Received 11 April 2017; Accepted 31 May 2017; Published 4 July 2017

Academic Editor: Zhien Zhang

Copyright © 2017 Guangya Jin and Zhijian Liu. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. J. Jing, N. Duan, K. Dai et al., “Investigation on drag characteristics of heavy oil flowing through horizontal pipe under the action of aqueous foam,” Journal of Petroleum Science and Engineering, vol. 124, pp. 83–93, 2014. View at Publisher · View at Google Scholar · View at Scopus
  2. F. J. Argüelles-Vivas and T. Babadagli, “Drainage type oil and heavy-oil displacement in circular capillary tubes: two-and three-phase flow characteristics and residual oil saturation development in the form of film at different temperatures,” Journal of Petroleum Science and Engineering, vol. 118, pp. 61–73, 2014. View at Publisher · View at Google Scholar · View at Scopus
  3. J.-E. Forero, O.-P. Ortíz, F.-A. Nariño, J. Díaz, and H. Peña, “Design and development of a high efficiency tank for crude oil dehydration,” Ciencia, Tecnología y Futuro, vol. 3, no. 4, pp. 185–199, 2008. View at Google Scholar · View at Scopus
  4. W. Wang, J. Gong, and P. Angeli, “Investigation on heavy crude-water two phase flow and related flow characteristics,” International Journal of Multiphase Flow, vol. 37, no. 9, pp. 1156–1164, 2011. View at Publisher · View at Google Scholar · View at Scopus
  5. Q. Li, F. B. Li, and X. Y. Su, “Research on a new type of device of laminar water draining with no external force,” Advanced Materials Research, vol. 201-203, pp. 2238–2241, 2011. View at Publisher · View at Google Scholar · View at Scopus
  6. Y. Q. Xu, Z. C. Guan, Y. W. Liu, L. C. Xuan, H. N. Zhang, and C. B. Xu, “Structural optimization of downhole float valve via computational fluid dynamics,” Engineering Failure Analysis, vol. 44, pp. 85–94, 2014. View at Publisher · View at Google Scholar · View at Scopus
  7. Y. Shi, F. Tang, and X. Wang, “Simulation research on micro-avity flow field characteristics of liquid floating rotor gyro,” Key Engineering Materials, vol. 562-565, pp. 490–495, 2013. View at Publisher · View at Google Scholar · View at Scopus
  8. Test method for gel point of crude oils. SY/T0541-2009, Standard, China, 2009.
  9. I. G. Harpur, N. J. Wayth, A. G. Bailey, M. T. Thew, T. J. Williams, and O. Urdahl, “Destabilisation of water-in-oil emulsions under the influence of an A.C. electric field: experimental assessment of performance,” Journal of Electrostatics, vol. 40, pp. 135–140, 1997. View at Publisher · View at Google Scholar · View at Scopus
  10. K. Mahdi, R. Gheshlaghi, G. Zahedi, and A. Lohi, “Characterization and modeling of a crude oil desalting plant by a statistically designed approach,” Journal of Petroleum Science and Engineering, vol. 61, no. 2-4, pp. 116–123, 2008. View at Publisher · View at Google Scholar · View at Scopus
  11. J. Gong, Y. Zhang, L. Liao, J. Duan, P. Wang, and J. Zhou, “Wax deposition in the oil/gas two-phase flow for a horizontal pipe,” Energy and Fuels, vol. 25, no. 4, pp. 1624–1632, 2011. View at Publisher · View at Google Scholar · View at Scopus
  12. L. A. Dillard, H. I. Essaid, and W. N. Herkelrath, “Multiphase flow modeling of a crude-oil spill site with a bimodal permeability distribution,” Water Resources Research, vol. 33, no. 7, pp. 1617–1632, 1997. View at Publisher · View at Google Scholar · View at Scopus
  13. S. V. Patankar and D. B. Spalding, “A calculation procedure for heat, mass and momentum transfer in three-dimensional parabolic flows,” International Journal of Heat and Mass Transfer, vol. 15, no. 10, pp. 1787–1806, 1972. View at Publisher · View at Google Scholar · View at Scopus
  14. N. Yang, W. Wang, W. Ge, and J. Li, “CFD simulation of concurrent-up gas-solid flow in circulating fluidized beds with structure-dependent drag coefficient,” Chemical Engineering Journal, vol. 96, no. 1-3, pp. 71–80, 2003. View at Publisher · View at Google Scholar · View at Scopus
  15. Z. Zhang, Y. Yan, D. A. Wood et al., “Influence of the membrane module geometry on so2 removal: a numerical study,” Industrial and Engineering Chemistry Research, vol. 54, no. 46, pp. 11619–11627, 2015. View at Publisher · View at Google Scholar · View at Scopus
  16. S. Eiamsa-ard and P. Promvonge, “Numerical simulation of flow field and temperature separation in a vortex tube,” International Communications in Heat and Mass Transfer, vol. 35, no. 8, pp. 937–947, 2008. View at Publisher · View at Google Scholar · View at Scopus
  17. Z. Han, B. H. Dennis, and G. S. Dulikravich, “Simultaneous prediction of external flow-field and temperature in internally cooled 3-D turbine blade material,” in Proceedings of the ASME Turbo Expo 2000: Power for Land, Sea, and Air, American Society of Mechanical Engineers, Munich, Germany, 2000. View at Publisher · View at Google Scholar
  18. C. M. Rhie and W. L. Chow, “Numerical study of the turbulent flow past an airfoil with trailing edge separation,” AIAA Journal, vol. 21, no. 11, pp. 1525–1532, 1983. View at Publisher · View at Google Scholar · View at Scopus