Table of Contents Author Guidelines Submit a Manuscript
International Journal of Aerospace Engineering
Volume 2017, Article ID 3616932, 15 pages
https://doi.org/10.1155/2017/3616932
Research Article

Nonlinear Material Behavior Analysis under High Compression Pressure in Dynamic Conditions

1School of Mechanical and Manufacturing Engineering, National University of Sciences and Technology, Islamabad, Pakistan
2Université Catholique de Louvain, Louvain-la-Neuve, Belgium
3Birmingham City University, Birmingham, UK
4School of Mechanical Engineering, Beijing Institute of Technology, Beijing, China

Correspondence should be addressed to Shahid Ikramullah Butt; kp.ude.tsun.emms@dihahsrd

Received 25 February 2017; Revised 7 June 2017; Accepted 4 July 2017; Published 29 August 2017

Academic Editor: Paul Williams

Copyright © 2017 Muhammad Zubair Zahid et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. A. Wilkinson, Conventional Ammunition in surplus - A reference guide, Chapter 6 - Stockpile Management: Surveillance and Proof, Small Arms Survey, Graduate Institute of International Studies, Geneva, Switzerland, 2008, ISBN 2-8288-0092-X.
  2. W. H. Ming, P. D. Xing, Z. Yu, and W. Yan, “Research of miniature internal electronic piezo gauge,” Electronic Design Engineering, vol. 17, no. 12, pp. 29–31, 2009. View at Google Scholar
  3. F. Coghe, L. Elkarous, P. van de Maat, A. Khadimallah, and M. Pirlot1, “Comparison of piezoelectric and crusher measurements of Chamber pressure with finite element modeling results,” in International Symposium on Ballistics, Freiburg, Germany, 2013. View at Google Scholar
  4. J. Z. Xin’e Li, T. Ma, and P. Xu, “Measuring chamber pressure of different caliber artilleries using a capacitive pressure sensor,” Sensors and Materials, vol. 23, no. 5, pp. 277–292, 2011, MYU Tokyo. View at Google Scholar · View at Scopus
  5. AEP-23 ED. 2, Pressure Measurement by Crusher Gauges NATO Approved Tests For Crusher Gauges, NATO Standardization Agreemens, 2005.
  6. NATO, “NATO piezo gauge replacement programme,” 1997, AC/225(LG/3-SG/1)D/3(Rev.).
  7. NATO, “Combination electronic pressure, velocity and action time (EPVAT) test procedure,” 2004, PFP (NAAG-LG/3-SG/1)D1 Chapter 12.
  8. International Permanent Commission (C.I.P), “Edition Synthétique des decisions C.I.P. en vigueur,” in Bureau Permanent C.I.P, Brussels, Belgium, 2011. View at Google Scholar
  9. SAAMI/ANSI standards, Sporting Arms and Ammunition Manufacturers' Institute (SAAMI) Technical Committee, 2017, http://www.saami.org/index.cfm.
  10. D. Crescini, D. Marioli, E. Sardini, and A. Taroni, “Low-cost thick film sensor based on piezoelectric effect for ballistic application,” Sensors and Actuators, vol. 87, pp. 131–138, 2001. View at Google Scholar · View at Scopus
  11. V.-T. Kuokkala, J. Ramo, and T. Vuoristo, Calibration of Crusher Pressure Gauges by High Strain Rate Testing, Tampere University of Technology, Institute of Materials Science, Tampere, Finland, P.O.Box 589, FIN-33101.
  12. Ballistic Standardization of Gun Ammunition Part 8, “Crushers and Crusher gauges,” 1991, Defense Standard 13–36 (PART 8), Issue 1, 8 February 1991.
  13. L. Elkarous, F. Coghe, M. Pirlot, and J. C. Golinval, “Experimental techniques for ballistic pressure measurements and recent development in means of calibration,” Journal of Physics: Conference Series, vol. 459, Article ID 012048, 2013. View at Publisher · View at Google Scholar · View at Scopus
  14. NATO, “Manual of Proof and Inspection Procedures for NATO 7.62 mm Ammunition MOPI,” 1997, AC/225(LG/-SG/1)D/9, p. 28.
  15. 1997, Proof and Inspection Procedures (MOPI) for 7.62mm Ammunition NATO Manual No. AC/225 (LG/3-SG/1) D/9.
  16. North Atlantic Treaty Organization (NATO), “Standardization agreement for small arms ammunition (7.62 mm),” in STANAG No. 2310, edition 3, Annex C, 1976.
  17. Kistler Group, “Operating instruction for high pressure quartz transducers 6203,” in No. B3.013e, edition 10.85, pp. 1–33.
  18. F. J. Zerilli and R. W. Armstrong, “Description of tantalum deformation behavior by dislocation mechanics based constitutive relations,” Journal of Applied Physics, vol. 68, pp. 1580–1591, 1990. View at Publisher · View at Google Scholar · View at Scopus
  19. G. R. Johnson and W. H. Cook, “A constitutive model and data for metals subjected to large strains, high strain rates and high temperatures,” in Proceedings of the 7th International Symposium on Ballistics, p. 547, The Hague, The Netherlands, 1983.