Abstract
A compact ultra-wideband (UWB) multiple input-multiple output (MIMO) antenna with high isolation is designed for UWB applications. The proposed MIMO antenna consists of two identical monopole antenna elements. To enhance the impedance matching, three slots are formed on the ground plane. The arc structure as well as the semicircle with an open-end slot is employed on the radiating elements the fact which helps to extend the impedance bandwidth of the monopole antenna from 3.1 up to 10.6 GHz, which corresponds to the UWB band. A ground branch decoupling structure is introduced between the two elements to reduce the mutual coupling. Simulation and measurement results show a bandwidth range from 3.1 to 11.12 GHz with |_|<−15 dB, |_|<−20 dB, and ECC < 0.002.
1. Introduction
UWB technology has been developed rapidly since FCC assigned a range of 3.1–10.6 GHz for UWB applications in 2002 [1]. The UWB communication system is well known for its fundamental advantages, which are low power and high data interference immunity [2]. However, one significant issue with this system is multipath fading, which is considered to be a prominent factor that affects the communication reliability of multisignals as well as the efficiency of an UWB system [3, 4]. Thus, to overcome this problem, MIMO has been introduced as an efficient technique to improve the UWB system performance.
MIMO technology has caught our attention as it significantly increased channel capacity without any additional power or bandwidth [5, 6]; however, we have found the mutual coupling between the UWB antenna elements which are very large to get installed on a confined space with the multiple antenna elements. It means that, if the MIMO antenna elements were placed very close to each other, there would be a strong correlation between their signals and the utility of MIMO would be reduced, so the mutual coupling is inversely proportional to the separation between the antenna elements. Thus, it is a challenge to design an UWB MIMO antenna with extremely compact structures and that have a low mutual coupling [7, 8]. We can say that the most critical point that must be considered while designing a MIMO antenna is to attain a low mutual coupling amid adjacent radiating elements because the MIMO antenna system performance can be strongly affected by the mutual coupling between the MIMO antenna elements, which considerably alter impedance matching, radiation efficiency, and channel capacity [9].
Based on the previous reasons, it is necessary to design UWB MIMO antennas with high isolation between their elements. Therefore, various techniques have been applied for the improvement of isolation amid closely spaced antennas, and several approaches have also been used to diminish the mutual coupling between the antenna elements. They include electromagnetic band gap (EBG) structures, defected ground structures (DGS), orthogonal polarization, placing metal strips between elements, metasurfaces, and neutralization line technique [10–14].
In [11], a high isolation MIMO antenna was designed for UWB applications and was exposed; between two of its elements, a comb-line structure was inserted in order to achieve high isolation. In [15], an UWB MIMO antenna was proposed with two rejected bands to avoid the interference between UWB applications and narrow band “ones.” In [16], MIMO antenna elements were placed vertically to minimize mutual coupling, and four notched bands were achieved by inserting symmetrical L-shaped slots and C-shaped stubs in each element. In [17], two MIMO configurations were discussed. In the first one, the antenna elements were placed side by side with a separated ground plane. In the second configuration, the antenna elements were orthogonally placed and had a separated ground plane as well.
The UWB MIMO antenna in [18] could achieve a mutual coupling larger than 20 dB in the entire operating band by etching a T-shaped slot as well as a narrow slot on the ground plane. In [12], a miniaturized MIMO antenna has been proposed for industrial applications, which had a novel decoupling stub structure etched in the ground plane to improve isolation between the antenna elements over the complete frequency band.
In [19], the developed MIMO antenna consists of a pair of rectangular patch elements, with staircase truncations at the patch-feed interconnection. DGS techniques as well as arc-shaped and split ring slots were used to obtain two band notches. In [13], two circular disc monopole antenna elements were designed for the proposed UWB-MIMO antenna. The mutual coupling between the two elements has been enhanced by using an inverted Y-shaped stub on the ground plane, which helps to miniaturize the antenna.
In this paper, an UWB antenna with high isolation characteristics is presented. The MIMO antenna uses two monopole antenna elements with a compact size of 8.3 × 11 mm2 in each. An arc structure as well as an open-end slot is formed in the radiating elements in order to cover a wide bandwidth for UWB applications.
A ground branch decoupling structure was used to minimize the coupling between the radiating elements. A bandwidth of 3.1–11.12 GHz is covered, and high isolation, of more than −19 dB on the entire band, is achieved.
2. Proposed Antenna Design
The antenna is mounted on a mm3 FR-4 substrate with a dielectric constant and a loss tangent of 0.0027. Figure 1 exhibits the geometry of the UWB MIMO antenna.
There are two similar owl-shaped radiating elements with a size of (, ) in the system. A partial ground plane (, ) is used with three slots with dimensions (, , , ) to improve impedance matching. An arc structure () is formed on the two corners of radiating elements in order to shift the frequency to a lower one.
Finally, a semicircle () with an open-ended slot () is applied on the two elements to cover the entire UWB frequency band. The radiating elements are fed by a microstrip line with dimensions (, ).
The final step on the design of our antenna was to apply a decoupling structure with dimensions (, ) in the ground plane in order to reduce the mutual coupling between the elements. Computer Simulation Technology (CST) Microwave Studio Software is used to simulate the proposed antenna.
After performing several simulations using CST MWS, the optimized parameters of the proposed UWB antenna are listed in Table 1.
3. Discussion of Design Process
The described MIMO antenna in Figure 1 is constructed by joining two UWB monopole antenna elements. This design has been chosen because of its attractive characteristics, which are simple structure, omnidirectional radiation pattern, low profile, and wide bandwidth. The frequency corresponding to the resonance of a rectangular planar monopole antenna can be approximately calculated by [20] where and denote the length of the ground plane and the monopole antenna, respectively, and is the gap between them. According to Formula (1), the calculated is 6.8 GHz, which corresponds to the center frequency of an UWB band. The dimensions of the initial monopole antenna structure have been chosen to obtain a resonant frequency of 6.8 GHz which represents the center frequency of an UWB since our purpose is to design a MIMO antenna for UWB applications. Figure 2 shows the single element of our proposed MIMO antenna.The simulated || is less than −10 dB across the whole band which is due to the compact size of the antenna elements and the ground plane. Therefore, in order to shift the resonant frequency to get it lower and improve the impedance matching, a modification is applied on the ground plane by changing its length . The obtained results in || implies that the partial ground plane has a significant effect on the input impedance matching, as shown in Figure 3(a), which represents the ||with varying the length of the ground plane.
(a)
(b)
(c)
(a)
(b)
(c)
(d)
On the other hand, by placing the two antenna elements close to each other, the bandwidth still cannot cover the entire UWB, so to shift the resonant frequency of the low band to a lower one, three small rectangular slots are cut on the ground plane, as well as by changing from 3 to 1 mm, the lower frequency is shifted from more than 4 GHz to about 3 GHz as shown in Figure 3(b).
Moreover, by forming an arc structure on the two corners of the two antenna elements as well as by applying a semicircle with an open-end slot on them, a good impedance matching is obtained across the whole UWB frequency band as it is shown in Figure 3(c).
Finally, by decreasing the value of the length of the radiating elements () from 10 to 8.3 mm, a bandwidth of 3.1–11.12 is covered.
4. Isolation Improvement
The described MIMO antenna in Figure 4(a) is constructed by joining two UWB monopole antenna elements, which are placed side by side, a distance from each other, with a common ground plane. Since the ground plane is very compact, the surface current and the near-field radiation cause strong mutual coupling between the UWB antennas, which leads to a signal interference that limits the MIMO system efficiency.
(a)
(b)
In order to improve isolation, several simulations and parametric studies were performed to obtain the optimum distance between the antenna elements. Figure 4(b) illustrates a parametric study of as a function of .
Results show that with , the antenna elements achieve better isolation. As shown above, isolation can be easily improved by increasing the distance between the antenna elements, but the compact size of the wireless devices limits this approach.
Therefore, a good challenge has appeared, meaning, in order to enhance isolation or to reduce the mutual coupling by using some other technique. Among these techniques, we can find the implementation of a decoupling structure between the antenna elements.
Figure 1 depicts our proposed antenna with a decoupling structure that is well known in the literature by a protruded ground branch.
As shown in Figures 5(a) and 5(b), as increases and decreases, the isolation is improved significantly while a good impedance matching is maintained across the UWB frequency band. Figure 5 represents the -parameters of the proposed MIMO antenna with a variation in the length () and the width () of the decoupling structure.
(a)
(b)
(c)
(d)
The main objective of introducing the stub on the ground plane of the antenna is to enhance the isolation between the ports of the constituent radiating elements; therefore, its significance can be evaluated by observing the -parameters of the proposed UWB MIMO antenna, comparing them with those that are without a stub.
Figure 6 shows the simulated -parameters of the developed UWB MIMO antenna with and without the decoupling structure.
The final step when the final antenna is designed with the optimized dimensions is to simulate the input impedance of our proposed antenna, in order to check the adaptation. Figure 7 illustrates the -parameters of our proposed antenna. So, as we can see in Figure 7, the adaptation is attained over the whole UWB band.
To further understand the effects of the decoupling structure on the mutual coupling between the antenna elements, Figure 8 shows the current distribution of our proposed antenna with and without using the decoupling structure which is obtained by exciting port 1.
(a) Without the decoupling structure (4.95 GHz)
(b) With the decoupling structure (4.95 GHz)
(c) Without the decoupling structure (8.52 GHz)
(d) With the decoupling structure (8.52 GHz)
The current is mainly concentrated on the feed line of the excited element, while a significant amount of current is flowing through the decoupling structure between the two elements of our proposed antenna which nullifies radiation. So the coupling between the antennas is minimized.
5. Results and Discussions
The Rohde and Schwarz ZVB 20 vector network analyzer is used to measure the proposed antenna -parameters by connecting port 1 and port 2 with two SMA female connectors. The photographs of the fabricated UWB MIMO antenna are shown in Figure 9.
The results indicate that our antenna is giving a good impedance bandwidth with both measured and simulated -parameters; < −15 dB from 3.1–11.12 GHz and are less than −20 dB throughout the ultra-wideband. Figure 10 illustrates the simulated and measured -parameters.
5.1. Radiation Patterns
It is clear that the -plane corresponds to the -plane and the -plane corresponds to the -plane. The radiation patterns are obtained by using an active element pattern. It means the radiation patterns of a single element, when the other one is presented but is not excited. It is also known as an embedded element pattern. The simulated and measured -plane and -plane radiation patterns of the proposed antenna are illustrated in Figure 11.
(a)
(b)
As we can see, as the frequency increases, the radiation pattern gets distorted. Note that the radiation patterns in the -plane as well as in the -plane are omnidirectional to receive the signals from all directions.
The difference between the simulated and the measured radiation patterns of the -plane occurs because the measurement is not carried out an anechoic chamber.
5.2. Envelope Correlation Coefficient
The envelope correlation coefficient presents an important factor for the comparison of MIMO capabilities of coupled antennas.
In general, there are three methods to calculate the envelope correlation coefficient. The first one consists of using far-field pattern data, which is considered to be a method that consumes much time because of its computational complexity.
The second method is based on Clarke’s formula, while the third one employs the scattering parameter formulation which can reduce the calculation complexity using the other methods. The last method can easily be generalized to the envelope correlation of a system with N-antenna [21].
So in order to have a better evaluation of MIMO diversity characteristic, an easy formula to compute ECC is provided:
Based on the measured -parameters, using Formula (2), and comparing it with the simulated one depicted in Figure 12, we obtained a result that showed that the ECC is less than 0.002 from 3.1–11.2 GHz which demonstrates the diversity good performance.
As it is shown in Figure 13, the value of the simulated gain of the proposed MIMO antenna has ranged from 2.5 to 5.54 over the UWB frequency band.
6. Conclusion
A novel compact owl-shaped UWB MIMO antenna is presented in this paper. Three slots were etched on the ground plane to improve impedance matching of the radiating elements to better than −15 dB. An arc structure as well as an open-end slot were applied on the radiating elements in order to cover the whole UWB band. A protruded ground branch was introduced in between the antenna elements to decrease the mutual coupling; a high isolation of less than −20 dB across the whole band was achieved.
Good radiation performances were also obtained. An envelope correlation coefficient of less than 0.002 was achieved, and a good gain value which is restricted to an average between 2.5 and 5.54 dB was obtained.
These results prove that the proposed owl-shaped MIMO antenna is very adequate for UWB applications.
Data Availability
The data used to support the findings of this study are included in the article.
Conflicts of Interest
The authors declare that there is no conflict of interests regarding the publication of this paper.
Acknowledgments
This research was partially supported by the National School of Applied Sciences, under Sciences and Advanced Technologies Laboratory, Abdelmalek Essaadi University, Tetouan, Morocco, supervised by Professor Alia Zekriti.