Abstract

It is noteworthy that ammoniacal nitrogen contamination in wastewater has reportedly posed a great threat to the environment. Although there are several conventional technologies being employed to remediate ammoniacal nitrogen contamination in wastewater, they are not sustainable and cost-effective. Along this line, the present study aims to highlight the significance of green chemistry characteristics of phytoremediation in nitrogen for wastewater treatment. Notably, ammoniacal nitrogen can be found in many types of sources and it brings harmful effects to the environment. Hence, the present study also reviews the phytoremediation of nitrogen and describes its green chemistry characteristics. Additionally, the different types of wastewater contaminants and their effects on phytoremediation and the phytoremediation consideration in wastewater treatment application and sustainable waste management of harvested aquatic macrophytes were reviewed. Finally, the present study explicates the future perspectives of phytoremediation. Based on the reviews, it can be concluded that green chemistry characteristics of phytoremediation in nitrogen have proved that it is sustainable and cost-effective in relation to other existing ammoniacal nitrogen remediation technologies. Therefore, it can be deduced that a cheaper and more environmental friendly ammoniacal nitrogen technology can be achieved with the utilization of phytoremediation in wastewater treatment.

1. Introduction

Ammoniacal nitrogen is one of the wastewater contaminants, which can be found in many types of wastewater. Excessive ammoniacal nitrogen in water body may lead to eutrophication, which induces the growth and decay of excessive plant and algal, and caused degradation of the water quality [1]. Notably, algal blooms may limit light penetration. On the other hand, eutrophication promotes anoxia in the water body, which leads to unpleasant and injurious gases, and endangers fish and invertebrates [1]. To date, there are several current methods being employed for the removal of ammoniacal nitrogen in wastewater. Ammoniacal nitrogen may be removed by means of conventional air stripping tower, which can only remove around 60% to 90% ammoniacal nitrogen. However, it should be noted that this process requires the use of chemicals for pH value control, therefore imposing higher treatment cost and lime-related operating and maintenance problems. Apart from the conventional air stripping tower, ammoniacal nitrogen can also be removed with break-point chlorination. This process is able to remove 90% to 100% of ammoniacal nitrogen, but it generates high chlorine residual and can be detrimental to the aquatic life. In addition, it requires careful control of the pH value in order to prevent the formation of nitrogen trichloride gas.

To date, phytoremediation is regarded as one of the most economically viable, sustainable, and affordable technologies. This is due to the fact that plants-based systems and microbiological processes were utilized in phytoremediation to reduce pollutants in nature [2]. It is an in situ remediation technology, which is ecologically friendly and solar dependent clean-up technology [2]. It is noteworthy that phytoremediation is a green chemistry process which offers a sustainable alternative and cost-effective technology in relation to conventional ammoniacal nitrogen clean-up technology for industrial tertiary wastewater treatment. Consequently, the present study aims to highlight the significance of green chemistry characteristics and the sustainability of phytoremediation in nitrogen remediation for wastewater treatment.

2. Ammoniacal Nitrogen: Sources and Effect in the Environment

Ammonia is colourless gas and exhibits a pungent smell at ambient temperature and pressure. It is the main constituent of domestic wastewater concentrations. It is very soluble in water and exists in equilibrium between ionized ammonia (NH3) and ionized ammonia (NH4+) species in water [3]. A number of studies indicated that the total ammonia toxicity is caused by the effect of unionized NH3 [3]. Total ammonia is usually referred to as the summation of ammonia and ammonium concentrations [4]. The ammonium ions is an important element, which is needed in plants for growth. Notably, ammonia enters the environment by means of the municipal, agricultural, industrial, and also natural activities [5]. Also, ammonia enters the environment from natural sources due to the degradation of organic waste matter, gas exchange with atmosphere, animal waste, and nitrogen fixation [6]. There are two types of sources on how ammonia enters the environment, namely, point and nonpoint sources. Point sources of ammonia derive from the emissions and effluent from various types of industrial plants. On the other hand, the nonpoint sources of ammonia are from agricultural, residential, municipal, and atmospheric releases [6].

The presence of ammoniacal nitrogen in water leads to environmental problems, such as eutrophication of surface water, changes in ecosystems, and acidifications [43]. In aquatic eutrophication, the ammoniacal nitrogen works as a source of nitrogen, which is needed for the production of nitrates. The high concentration of nitrates and ammonia in water body may result in a toxic environment and may cause oxygen deficiency environments resulting from the nitrification process. Severe eutrophication may lead to a hypoxic condition, which is a dead zone where no aquatic life can survive [43].

3. Phytoremediation of Ammoniacal Nitrogen

The plant utilization of nitrogen involves few steps including the uptake, assimilation, and translocation [44]. Plants take up mainly three forms of nitrogen, namely, nitrate ions, urea, and ammonium ions. Once ammonia is present in the plant cell, it is incorporated into proteins and other organic combinations through a biochemical reaction. However, only the ammonium ion is assimilated into the organic molecules in the plant tissues by means of enzymatic process [44]. Ammonium and nitrate ions are the principal sources of nitrogen for plant growth and are necessary in larger amount than the other mineral nutrients. In comparison to nitrate, ammonium is absorbed by the plants more quickly [45]. This is due to the lower energy requirement for the uptake and assimilation of ammonium ions in relation to the nitrate ions [46]. It should be noted that the ammonium ions can be directly absorbed by the roots of the plants or as a result of nitrate ion reduction, it is further assimilated into the amide amino group of glutamine by the glutamine synthetase and subsequently, into glutamic acid by the glutamate synthase. These two enzymes resulted in the assimilation of most of the ammonium ions [44]. Notably, the ammonium ions are toxic and not permitted to be stored in plants. Hence, the ammonium ions are either oxidized nitrates ions, assimilated to produce amino acids, or converted to amides [47].

When the plants take up ammonium ions, they release one hydrogen ion in the medium solutions. Over time, the uptake of ammoniacal nitrogen may increase the hydrogen ions concentration, hence decreasing the growing medium pH value. However, an increase of ammonium uptake in plants and storage may result in cell damage and further leads to cell death [48]. The ammonium ions are taken up by the plants from the root uptake. The nitrogen uptake by the root system depends on the nitrogen demand of the entire plant and is dependent on the nitrogen requirement for growth. Nitrogen starvation of plants for several days may lead to the increased capacity for ammonium uptake [48].

4. Green Chemistry Characteristics of Phytoremediation

Green chemistry is defined as the chemical products and processes that lessen or prevent the production of hazardous substances. The application of green chemistry does not only bring benefits to the environment, but also lead to innovation and enhanced economy [49]. In phytoremediation, only plants were needed for the remediation process. It should be noted that phytoremediation of ammoniacal nitrogen process possessed green chemistry characteristics, such as no chemical usage, energy efficient, and safer reaction condition in relation to the conventional ammoniacal remediation technology.

4.1. No Chemical Usage

In comparison to conventional ammoniacal nitrogen remediation technology, the phytoremediation process requires no chemical usage. The chemicals required for the conventional ammoniacal remediation technology may add up additional operational cost. This cost is considered as a loss as it does not add up to the company’s profit. Notably, no chemical is needed for phytoremediation process. The plants naturally take up ammonium ions from the wastewater to support its growth. Besides that, the plants used in phytoremediation are renewable feedstock that aids in the reduction on climate change by the fixation of carbon dioxide [50]. The existing ammoniacal nitrogen remediation technology and phytoremediation with the chemical required for each process are presented in Table 1.

Ferraz et al. (2013) employed lime and powdered calcium hydroxide to increase the pH value to 11 of the leachate for ammonia stripping, in which the ammonia stripping tower reduces at 88% of the initial TAN concentration in the pH value of 11 leachate [7]. However, the formation of calcium carbonate scale resulted in the reduction of ammonia stripping performance [51]. Viotti and Gavasci (2014) revealed that progressive scaling reduces the ammonia removal efficiency by 18% of the ammonia stripper [51]. It is noteworthy that ion exchange for the removal of ammoniacal nitrogen utilized regenerant for the regeneration of the clinoptilolite. Interestingly, the costs of chemicals, which are required for regeneration made up a major fraction of the cost of ion exchange process [8]. As regards the removal ammoniacal nitrogen using break-point chlorination, chlorine gas and lime are used. The total costs of the chemicals for break-point chlorination for 300 MGD with 15 mg/L of ammoniacal nitrogen influent plant are 1.47 cents/1000 L of wastewater [9]. Mondor et al. (2007) used sodium sulphate and potassium chloride as the electrolytes for the electrodialysis of swine manure for ammonia recovery [10]. Notably, phytoremediation requires no chemical usage during the remediation process and this can save up the company’s operational cost. It is easy for aquatic macrophytes to be cultured for stock due to its fast growth and reproduction.

4.2. Reduction of Energy Consumption

As regards wastewater treatment plant, energy consumption is often associated with the amount of type and load of the pollutant. On average, nutrient removal technology has higher energy intensity [52]. Notably, phytoremediation is a solar-driven technology and hence, only the energy from sunlight is required for the phytoremediation process. The sunlight energy can be found in abundance all year round, especially in the countries with tropical climate. It should be noted that phytoremediation offers a relatively lower energy usage than the other existing ammoniacal nitrogen remediation technologies. Table 2 indicates the comparison on the energy consumption of the different types of ammoniacal nitrogen technology.

4.3. Inherently Safer Process

In comparison to some conventional ammoniacal nitrogen clean-up technologies, phytoremediation has safer reactions and lower risks. Phytoremediation provides an alternative to remediate ammoniacal nitrogen by means of using eco-friendly biomass rather than chemicals, which caused potential risks such as health hazards, chemical reaction hazards, fire and explosion hazards, and environmental hazards. Table 3 indicates the potential risk arising from the utilization of conventional ammoniacal nitrogen clean-up technology.

Many risk assessment studies have reported accidents involving ammonia with many subjects [53]. Campos et al. (2013) in their study of the evaluation of pH value, alkalinity, and temperature during the air stripping process for ammonia removal from landfill leachate bubbled the ammonia gas generated from ammonia stripping in acid for neutralizations [15]. Besides that, break-point chlorination may result in the generation of nitrogen trichloride, which is an explosive gas. Okado et al. (2014) reported in their study of analysis of an explosion accident of nitrogen trichloride in waste liquid containing ammonium ion and platinum black that the explosion of the liquid waste was due to the generation of nitrogen chloride [16]. Notably, there were no potential risks associated with phytoremediation, biological nitrification, and ion exchange process.

5. Wastewater Contaminants and Effects to Phytoremediation Performance

It is worth highlighting that the success of phytoremediation application for the industrial tertiary wastewater treatment, especially for nitrogen removal, is highly dependent on the characteristics of tertiary wastewater effluent. The industrial wastewater is comprised of a wide range of contaminants, which may cause toxicity to the aquatic macrophytes. Toxic contaminants that are present in the wastewater may inhibit the growth of the plants, which may affect the performance of the aquatic macrophytes in remediating the wastewater. According to Clarke and Baldwin (2002), different tolerance on ammonia concentrations was exhibited with different types of aquatic macrophytes and they concluded that the effectiveness of phytoremediation can be improved by choosing the aquatic macrophytes which have high tolerance of ammonia level in the wastewater [54]. Besides that, the tolerance of aquatic macrophytes on different types of contaminants present on the wastewater may also affect the ammoniacal nitrogen removal efficiency. According to Lu et al. (2004), reduced growth can be observed on the plants under heavy metal stress [18]. Apart from that, exposure to heavy metals in wastewater may also inhibit plant’s growth [55]. It is worth noting that the level of tolerance in different types of aquatic macrophytes with different ammoniacal nitrogen concentrations and other common wastewater contaminants were studied by several researchers. Table 4 displays some research carried out on tolerances of several aquatic macrophytes used for phytoremediation with different types of contaminants.

As shown in Table 4, different types of aquatic macrophytes have different tolerance with different types of wastewater contaminants. Eichhornia crassipes appears to be one of the most promising aquatic plants for tertiary industrial wastewater treatment due to its high tolerance with wide range of wastewater contaminants. Notably, it has high tolerance to most of the heavy metals and higher tolerance to higher ammoniacal nitrogen concentrations.

6. Phytoremediation Wastewater Treatment Application Consideration

The important parameters of phytoremediation must be considered to ensure the efficiency of the phytoremediation process. Among the important parameters are aquatic macrophytes species, salinity, temperature, and pH.

6.1. Aquatic Macrophytes Species

To date, a number of studies have been carried out on ammoniacal nitrogen uptake with different type of macrophyte species for wastewater treatment. In determining the suitability of macrophyte species to be utilized for phytoremediation, the rate of ammonium uptake by plants and the assimilation of these nutrients into the plant biomass are of utmost importance. The generated plant biomass may be utilized as an indicator to estimate the nutrient uptake capacity of the plants [56]. Table 4 indicates the list of macrophytes used by different researchers for the phytoremediation of ammoniacal nitrogen. However, the suitability of the aquatic macrophytes for different types of wastewater depends on the aquatic macrophytes tolerance on different types of contaminants in the wastewater as shown in Table 4.

6.2. Salinity

The effect of salinity stress on aquatic macrophytes may greatly affect the growth and reproduction of aquatic plants. Different types of aquatic macrophytes species have different tolerance range. According to Haller et al. (1974), the tolerance of aquatic macrophytes towards salinity may affect their performance in water treatment due to the reduction of transpiration and total dry weight with higher level of salinity and death [57]. According to Haller et al. (1974), large-leaved floating species is the most vulnerable to salinity, whereas submerged species may tolerate high level of salinity in comparison to large-leaved ones, and small-leaved species is the least vulnerable [57]. According to a study carried out by Lu (2009), salinity has a significant effect on plants dry biomass [58]. This is due to the fact that more new individuals of small size plant may not compensate for the biomass reduction due to the inhibited vegetative growth at high salinity level [58]. Notably, this high salinity level inhibits aquatic macrophytes water uptake by reducing the osmotic potential of the water. Haller et al. (1994) observed that Pistia stratiotes and Eichhornia crassipes may be significantly affected by lower salinities, which are around 10% and 13.32%, respectively [57]. Moreover, Lu (2009) observed that the Pistia stratiotes dry matter yield was reduced by approximately 30% in the 1766 μS cm−1 [58]. On the other hand, Pascale et al. (1997) observed that biomass production is inhibited at higher salinity [59].

6.3. Temperature

The performance of aquatic macrophytes in phytoremediation varies with temperature [60]. This is due to the fact that the phytoremediation performance of plants is dependent on the plants’ growth. Temperature is one of the most crucial ecological factors, which influence the productivity of a particular macrophyte species. Most of aquatic macrophytes are able to grow well between the temperatures of 20°C and 30°C and inhibited growth at the temperature of 10°C and below [61]. Shah et al. (2013) studied the performance of three aquatic macrophytes, which include Eichhornia crassipes, Lemna minor, and Pistia stratiotes regarding BOD5 removal. It was found that the optimum temperature for the three aquatic macrophytes’ growth ranges between 15°C and 38°C [60]. Nevertheless, different species of aquatic macrophytes may be used for cooler weather conditions. Reddy and Tucker (1985) stated that Centella asiatica can be successfully grown during cooler months and may be used to replace Eichhornia crassipes-based nitrogen wastewater treatment system [62].

6.4. pH

Wastewater pH value may influence the performance of aquatic macrophytes in remediating the ammoniacal nitrogen. Shah et al. (2014) reported that a pH value of 6–9 is the most favourable for the treatment of wastewater using aquatic macrophytes [60]. El-Gendy et al. (2004) in their study use Eichhornia crassipes, Pistia stratiotes, and Lemna minor to remediate municipal wastewater and reported that the optimal growth for Eichhornia crassipes is 7 [63]. However, it can withstand pH values ranging from 4 to 10 [63].

7. Harvesting Aquatic Macrophytes

It should be noted that the major issue with regard to phytoremediation is the large amount of biomass generated from this process. The most effective ammoniacal nitrogen removal deals with the harvested aquatic at the end of each vegetation cycle. Failure to harvest the aquatic macrophytes at its harvesting period may lead to the release of the stored ammoniacal nitrogen back into the wastewater.

7.1. Aquatic Macrophytes Biomass Yield

Aquatic macrophytes generated a large amount of biomass under nutrient-rich conditions [64]. To anticipate the amount of waste that will be generated, the amount of biomass-generated data is crucial. Also, this preliminary data is important in selecting the most appropriate waste management technique for phytoremediation. Notably, different types of aquatic macrophytes have different biomass yield as exhibited in Table 5.

Based on Table 5, Eichhornia crassipes has the highest maximum annual biomass yield at 0.0106 t dry wt m2 yr−1 and Lemna minor has the lowest maximum annual biomass yield at 0.0008 t dry wt m2 yr−1. It is worth noting that the success of wastewater treatment systems by means of using aquatic macrophytes is also determined by its growth rate. According to Greenway (2002), at low to medium nutrient concentrations, the biomass generation is proportional to nutrient supply [56].

7.2. Harvesting Period

It is worth highlighting that regular aquatic macrophytes harvesting is crucial in order to prevent the release of stored ammoniacal nitrogen back into the wastewater. Hence, a well-planned harvesting schedule is of utmost importance in order to ensure an efficient ammoniacal nitrogen removal. Table 6 displays the leaf lifespan of the different types of aquatic macrophytes.

Some of the leaf lifespan of aquatic macrophytes is affected by the dissolved inorganic nitrogen concentrations. Tsuchiya and Iwakuma (1993) discerned that the nutrient level may affect the leaf lifespan of Hydrocharis dubia L. [40]. The results of their study showed that the leaf lifespan is relatively longer in lower concentration of nutrients [40]. Tsuchiya (1989) revealed that the leaf lifespan of Trapa natans is shortened at higher nutrient concentrations (i.e., at 30 mg N/L) [41]. Notably, Chabot and Hicks (1982) echoed that leaf lifespan is related to nutrient availability [65]. Eichhorna crassipes has the longest leaf lifespan, which is 35 days. Both Spirodela polyrhiza and Wolffia borealis have the lowest leaf lifespan, which is 12 days. It should be noted that the shorter the leaf lifespan of the aquatic macrophyte is, the more frequent it is to harvest the aquatic macrophytes. However, the leaf lifespan of aquatic macrophytes also depends on the characteristics of the wastewater, which is very sensitive heavy metal exposure (shown in Table 4).

8. Sustainable Management of Harvested Aquatic Macrophytes

Seadon (2010) posits that a sustainable waste management integrates feedback loops and avoid wastes from disposal [66]. Aquatic macrophytes is an organic matter, which can be broken down and can be converted into value-added products.

8.1. Biogas

Biogas is an environmentally clean fuel, which is generated from the anaerobic digestion of organic waste [67]. To generate biogas, aquatic macrophytes may be used due to its high carbon to nitrogen ratio and high content of fermentable matter [68]. Aquatic macrophytes, such as Eichhornia crassipes, Trapa natans, Typha latifolia, Salvinia molesta, Lemna minor, and Pistia stratiotes, can generate high biogas yield and be decomposed easily ([6973]). Ngoju et al. (2015) stated that Eichhornia crassipes can be a potential feedstock for biogas generation. Also, they found that the biogas generated from Eichhornia crassipes feedstock comprised 49–53% of methane, 30–34% of carbon dioxide, 5-6% nitrogen, and relatively small amount of hydrogen sulphide [74]. On the other hand, factors affecting biogas yield from the aquatic macrophytes biomass include particle size, volatile solid content, plant composition (i.e., nitrogen, carbon, and phosphorus), trace nutrients, and inoculum volume [74]. According to Kathusi (2016), biogas generated from harvested aquatic macrophytes has the potential to be an effective strategy in reducing environmental problems with regard to top climate change, phytoremediation, eutrophication, acidification, and water pollution [75]. Besides that, Kathusi (2016) also concluded that biogas production from harvested aquatic macrophytes is commercially potential and sustainable [76]. Verma et al. (2007) discerned that the biogas generated from an Eichhornia crassipes and Trapa natans grown in brass and electroplating industry effluent was relatively higher due to the presence of various pollutants acting as a micronutrients for the aquatic macrophytes. They found that aquatic macrophytes grown in polluted wastewater increase the economic success of the energy generation from waste [77].

8.2. Vermicompost

The product of microbial degeneration of organic waste by using earthworms is known as vermicompost. Vermicompost is found to be rich with nutrients [78]. Bernal and Hernandez (2016) revealed that vermicompost from Eichhornia crassipes can be used as organic fertilizer or soil enhancer as it is rich in nutrients [79]. Furthermore, vermicompost from Eichhornia crassipes can be economical; it can be used to produce vermicompost in bulk by means of using the “high-rate method” and subjecting the vermicomposting in reactors with higher amount of earthworm than suggested hitherto [78]. Kostecka and Kaniuczak (2008) found that Lemna minor vermicompost is odourless with a good granular structure [80]. An efficient vermicomposting of Salvinia molesta with “high-rate” vermicompost technology using Eudrilus eugeniae developed by Gajalakshmi et al. (2014) may be employed for vermicomposting as it is faster and economical [78]. Mishra et al. (2016) discovered that phytoremediated aquatic macrophytes biomass into vermicompost is effective and environmentally friendly for sustainable agriculture [81]. Among the aquatic macrophytes used by Mishra et al. (2016) are Azolla microphylla, Pistia stratiotes, Salvinia cucullata, and Salvinia molesta [81]. According to Tereshchenko and Akimova (2014), the employment of Eichhornia crassipes in vermicomposting helps improve the biometric parameters in a 14-day experiment, even the trial with water hyacinth biomass grown in wastewater contaminated with heavy metals [82]. Moreover, they suggested that vermicompost from heavy metal laden Eichhornia crassipes may be used as soil for urban landscaping and rehabilitation of technologically disturbed sites [82]. Hence, vermicomposting can be a sustainable tool for sustainable management of the harvested aquatic macrophytes.

8.3. Papermaking

It is noteworthy that aquatic macrophytes are suitable with the aqueous characteristics of paper pulp due to their high moisture content [83]. Bidin et al. (2015) reported that aquatic macrophytes, namely, Scirpus grossus, Cyperus rotundus, and Typha angustifolia can be used in papermaking due to their fiber characteristics, chemical composition, and physical properties [84]. Goswami and Saikia (1994) concluded that Eichhornia crassipes pulp can be an ideal raw material for greaseproof paper production, when it is mixed with bamboo pulp [85]. Moreover, Thomas and Room (1986) reported that Salvinia molesta is suitable for the papermaking [86]. Nevertheless, the researchers deem that more research is needed with regard to the industrial application in order to ensure the sustainability of this process.

8.4. Biochar

Biochar is comprised of carbon-rich material generated from organic waste [87]. Miranda et al. (2014) investigated the potential of the harvested biomass of L. punctata, Elodea, and Marsilea from Selenium-rich wastewater as a feedstock for the production of biochar by means of using pyrolysis technology [88]. They found that the pyrolysis product of Lemna minor can be converted into gasoline and diesel [88]. Apart from that, Masto et al. (2013) reported that biochar from Eichhornia crassipes can be utilized as soil quality amendment [89]. By converting harvested aquatic macrophytes biomass grown in wastewater contaminated with heavy metals by pyrolysis, the accumulated heavy metal can be enclosed safely in the solid fraction of the char. The summarizations of sustainable waste management of the harvested aquatic macrophytes can be summarized in Figure 1.

9. Future Perspective

As regards the conventional ammoniacal nitrogen clean-up technology, phytoremediation offers a sustainable option for tertiary industrial wastewater treatment. Hence, a greater need for improving its efficiency for industrial application is of utmost importance due to the fact that it is environmentally friendly and cost-effective. However, phytoremediation is both time and space consuming because large surface area is required in order to retain the wastewater. Consequently, studies focusing on the development of phytoremediation reactor, which may reduce the surface area for larger volumes of wastewater and its longer retention time, are deemed necessary. Apart from that, it should be noted that phytoremediation standalone system is a less efficient and time-consuming process. Thus, the researchers deem that hybrid system of phytoremediation has the potential to increase the efficiency of phytoremediation. Putra et al. (2015) in their study of “Removal of Lead and Copper from Contaminated Water Using EAPR System and Uptake by Water Lettuce (Pistia Stratiotes L.)” reported that the overall metal uptake in plant system was higher under EAPR system compared to phytoremediation process [90]. Putra et al. (2015) concluded that the preliminary outcome of the experiment showed promising results in creating an inexpensive, eco-friendly hybrid system of electroassisted and phytoremediation system for the remediation of lead and copper contaminated wastewater [90]. Hence, more research and innovation on the different types of phytoremediation hybrid system in improving the efficiency and reliability of this green remediation technology for different types of wastewater contaminants are needed.

10. Conclusion

Based on the findings of the present study, it can be concluded that phytoremediation of nitrogen by means of using aquatic macrophytes possessed green chemistry characteristics. Moreover, it has been proven that the green chemistry characteristics of phytoremediation is sustainable and cost-effective in relation to other existing ammoniacal nitrogen remediation technology. Apart from that, Eichhornia crassipes appeared to be one of the most promising aquatic macrophytes for wastewater treatment due to its high tolerance with wide range of wastewater contaminants. Nevertheless, several parameters are deemed necessary to be taken into consideration in order to ensure the efficiency of the phytoremediation of ammoniacal nitrogen. Besides that, appropriate method for the removal of the harvested macrophytes must also be considered to ensure the sustainability of the phytoremediation process. Converting the harvested aquatic macrophytes into biogas and vermicompost can be a promising technique for a sustainable waste management for the phytoremediation process as proved by several researchers. However, more research is still needed for the conversion of the aquatic macrophytes into papermaking material and biochar. Notably, the hybrid system of phytoremediation for wastewater treatment may be a popular trend in the near future due to its cost effectiveness and increased efficiency in remediating wastewater.

Conflicts of Interest

The authors declare that there are no conflicts of interest regarding the publication of this article.