Table of Contents Author Guidelines Submit a Manuscript
International Journal of Dentistry
Volume 2016, Article ID 8590971, 9 pages
http://dx.doi.org/10.1155/2016/8590971
Clinical Study

3D Printing/Additive Manufacturing Single Titanium Dental Implants: A Prospective Multicenter Study with 3 Years of Follow-Up

1Private Practice, Rua Asia 173, Cerqueira Cesar, 05413-030 Sao Paulo, SP, Brazil
2Private Practice, Rua Inacio Pereira da Rocha 147, 05432-010 Sao Paulo, SP, Brazil
3Department of Periodontology, The Maurice and Gabriela Goldschleger School of Dental Medicine, University of Tel Aviv, Ramat-Aviv, 6997801 Tel Aviv, Israel
4Department of Oral Rehabilitation, The Maurice and Gabriela Goldschleger School of Dental Medicine, University of Tel Aviv, Ramat-Aviv, 6997801 Tel Aviv, Israel
5Department of Periodontology and Oral Implantology, Dental Research Division, Guarulhos University, Praca Teresa Cristina 229, 07023070 Guarulhos, SP, Brazil

Received 20 February 2016; Revised 14 April 2016; Accepted 5 May 2016

Academic Editor: Spiros Zinelis

Copyright © 2016 Samy Tunchel et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Citations to this Article [16 citations]

The following is the list of published articles that have cited the current article.

  • Shafia Tabassum, Ahmar Murtaza, Hasan Ali, Zia Mohy Uddin, and Syedah Sadaf Zehra, “Finite element analysis (FEA) of dental implant fixture for mechanical stability and rapid osseointegration,” vol. 1892, pp. 040016, . View at Publisher · View at Google Scholar
  • Aishwarya Bhargav, Vijayavenkatraman Sanjairaj, Vinicius Rosa, Lu Wen Feng, and Jerry Fuh YH, “Applications of additive manufacturing in dentistry: A review,” Journal of Biomedical Materials Research Part B: Applied Biomaterials, 2017. View at Publisher · View at Google Scholar
  • Karthika Prasad, Olha Bazaka, Ming Chua, Madison Rochford, Liam Fedrick, Jordan Spoor, Richard Symes, Marcus Tieppo, Cameron Collins, Alex Cao, David Markwell, Kostya (Ken) Ostrikov, and Kateryna Bazaka, “Metallic Biomaterials: Current Challenges and Opportunities,” Materials, vol. 10, no. 8, pp. 884, 2017. View at Publisher · View at Google Scholar
  • Jiang Wu, Yan Li, and Yumei Zhang, “Use of intraoral scanning and 3-dimensional printing in the fabrication of a removable partial denture for a patient with limited mouth opening,” The Journal of the American Dental Association, 2017. View at Publisher · View at Google Scholar
  • S.A. Shevchik, C. Kenel, C. Leinenbach, and K. Wasmer, “Acoustic emission for in situ quality monitoring in additive manufacturing using spectral convolutional neural networks,” Additive Manufacturing, 2017. View at Publisher · View at Google Scholar
  • Po-Chuan Chang, “Computer-Assisted Planning and 3D Printing-Assisted Modeling for Chin Augmentation,” Aesthetic surgery journal, vol. 38, no. 1, pp. 1–10, 2017. View at Publisher · View at Google Scholar
  • Sang-Mo Park, Seong-Kyun Kim, Ji-Man Park, Jang-Hyun Kim, Yoon-Tae Jeon, and Jai-Young Koak, “Flexural strength of various kinds of the resin bridges fabricated with 3D printing,” Journal of Dental Rehabilitation and Applied Science, vol. 33, no. 4, pp. 260–268, 2017. View at Publisher · View at Google Scholar
  • Amirmohammad Rahimizadeh, Zahra Nourmohammadi, Sajad Arabnejad, Michael Tanzer, and Damiano Pasini, “Porous architected biomaterial for a tibial-knee implant with minimum bone resorption and bone-implant interface micromotion,” Journal of the Mechanical Behavior of Biomedical Materials, 2017. View at Publisher · View at Google Scholar
  • Richard J. van Arkel, Shaaz Ghouse, Piers E. Milner, and Jonathan R. T. Jeffers, “Additive manufactured push-fit implant fixation with screw-strength pull out,” Journal of Orthopaedic Research, 2017. View at Publisher · View at Google Scholar
  • HaiMing Zhao, FeiFei Yang, JianZhong Fu, Qing Gao, An Liu, Miao Sun, and Yong He, “Printing@Clinic: From Medical Models to Organ Implants,” ACS Biomaterials Science & Engineering, 2017. View at Publisher · View at Google Scholar
  • Xiaokang Li, Peng Gao, Peng Wan, Yifeng Pei, Lei Shi, Bo Fan, Chao Shen, Xin Xiao, Ke Yang, and Zheng Guo, “Novel Bio-functional Magnesium Coating on Porous Ti6Al4V Orthopaedic Implants: In vitro and In vivo Study,” Scientific Reports, vol. 7, pp. 40755, 2017. View at Publisher · View at Google Scholar
  • Hong-Pu Wei, and Xu-Dong Wang, “Advances in titanium bone implants made by rapid prototyping technology,” Chinese Journal of Tissue Engineering Research, vol. 21, no. 22, pp. 3583–3588, 2017. View at Publisher · View at Google Scholar
  • Yifan Dong, Haibo Duan, Naru Zhao, Xiao Liu, Yijuan Ma, and Xuetao Shi, “Three-dimensional printing of $$\varvec{\upbeta }$$β-tricalcium phosphate/calcium silicate composite scaffolds for bone tissue engineering,” Bio-Design and Manufacturing, 2018. View at Publisher · View at Google Scholar
  • Bartłomiej Wysocki, Joanna Idaszek, Joanna Zdunek, Krzysztof Rożniatowski, Marcin Pisarek, Akiko Yamamoto, and Wojciech Święszkowski, “The Influence of Selective Laser Melting (SLM) Process Parameters on In-Vitro Cell Response,” International Journal of Molecular Sciences, vol. 19, no. 6, pp. 1619, 2018. View at Publisher · View at Google Scholar
  • Jan Stieghorst, and Theodor Doll, “Rheological Behavior of PDMS Silicone Rubber for 3D Printing of Medical Implants,” Additive Manufacturing, 2018. View at Publisher · View at Google Scholar
  • Vincent C. F. Li, Arie Mulyadi, Conner K. Dunn, Yulin Deng, and H. Jerry Qi, “Direct Ink Write 3D Printed Cellulose Nanofiber Aerogel Structures with Highly Deformable, Shape Recoverable, and Functionalizable Properties,” ACS Sustainable Chemistry & Engineering, 2018. View at Publisher · View at Google Scholar