Table of Contents
International Journal of Manufacturing Engineering
Volume 2016 (2016), Article ID 4680380, 9 pages
http://dx.doi.org/10.1155/2016/4680380
Research Article

Analyzing the Effect of Machining Parameters Setting to the Surface Roughness during End Milling of CFRP-Aluminium Composite Laminates

1Department of Mechanical and Manufacturing Engineering, Universiti Putra Malaysia, 43400 Serdang, Selangor, Malaysia
2Department of Aerospace Engineering, Universiti Putra Malaysia, 43400 Serdang, Selangor, Malaysia

Received 19 September 2015; Revised 18 January 2016; Accepted 8 February 2016

Academic Editor: Thomas R. Kurfess

Copyright © 2016 M. Nurhaniza et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. J. Y. Sheikh-Ahmad, Machining of Polymer Composites, Springer, New York, NY, USA, 2009.
  2. S. Jahanmir, M. Ramulu, and P. Koshy, Machining of Ceramics and Composites, Marcel Dekker, New York, NY, USA, 2000.
  3. M. Ramulu, C. W. Wern, and J. L. Garbini, “Effect of fibre direction on surface roughness measurements of machined graphite/epoxy composite,” Composites Manufacturing, vol. 4, no. 1, pp. 39–51, 1993. View at Publisher · View at Google Scholar · View at Scopus
  4. M. T. Hayajneh, M. S. Tahat, and J. Bluhm, “A study of the effects of machining parameters on the surface roughness in the end-milling process,” Jordan Journal of Mechanical and Industrial Engineering, vol. 1, no. 1, pp. 1–5, 2007. View at Google Scholar
  5. J. Z. Zhang, J. C. Chen, and E. D. Kirby, “Surface roughness optimization in an end-milling operation using the Taguchi design method,” Journal of Materials Processing Technology, vol. 184, no. 1–3, pp. 233–239, 2007. View at Publisher · View at Google Scholar · View at Scopus
  6. A. A. Sequeira, R. Prabhu, N. S. Sriram, and T. Bhat, “Effect of cutting parameters on cutting force and surface roughness of aluminium components using face milling process—a Taguchi approach,” IOSR Journal of Mechanical and Civil Engineering, vol. 3, no. 4, pp. 7–13, 2012. View at Google Scholar
  7. N. S. K. Reddy and P. V. Rao, “Selection of optimum tool geometry and cutting conditions using a surface roughness prediction model for end milling,” International Journal of Advanced Manufacturing Technology, vol. 26, no. 11-12, pp. 1202–1210, 2005. View at Publisher · View at Google Scholar · View at Scopus
  8. A. Hamdan, A. A. D. Sarhan, and M. Hamdi, “An optimization method of the machining parameters in high-speed machining of stainless steel using coated carbide tool for best surface finish,” International Journal of Advanced Manufacturing Technology, vol. 58, no. 1–4, pp. 81–91, 2012. View at Publisher · View at Google Scholar · View at Scopus
  9. G. Santhanakrishnan, R. Krishnamurthy, and S. K. Malhotra, “Machinability characteristics of fiber reinforced plastics composites,” Journal of Mechanical Working Technology, vol. 17, pp. 195–204, 1988. View at Publisher · View at Google Scholar · View at Scopus
  10. A. Koplev, A. Lystrup, and T. Vorm, “The cutting process, chips, and cutting forces in machining CFRP,” Composites, vol. 14, no. 4, pp. 371–376, 1983. View at Publisher · View at Google Scholar · View at Scopus
  11. G. C. Everstine and T. G. Rogers, “A theory of machining of fiber-reinforced materials,” Journal of Composite Materials, vol. 5, no. 1, pp. 94–106, 1971. View at Publisher · View at Google Scholar
  12. H. Gökkaya, “The effects of machining parameters on cutting forces, surface roughness, built-up edge (BUE) and built-up layer (BUL) during machining AA2014 (T4) alloy,” Journal of Mechanical Engineering, vol. 56, no. 9, pp. 584–593, 2010. View at Google Scholar
  13. B. A. Khidhir and B. Mohamed, “Study of cutting speed on surface roughness and chip formation when machining nickel-based alloy,” Journal of Mechanical Science and Technology, vol. 24, no. 5, pp. 1053–1059, 2010. View at Publisher · View at Google Scholar · View at Scopus
  14. A. I. Azmi, R. J. T. Lin, and D. Bhattacharyya, “Machinability study of glass fibre-reinforced polymer composites during end milling,” International Journal of Advanced Manufacturing Technology, vol. 64, no. 1–4, pp. 247–261, 2013. View at Publisher · View at Google Scholar · View at Scopus
  15. M. H. F. Al Hazza and E. Y. T. Adesta, “Investigation of the effect of cutting speed on the surface roughness parameters in CNC end milling using artificial neural network,” IOP Conference Series Materials Science and Engineering, vol. 53, no. 1, Article ID 012089, 2013. View at Publisher · View at Google Scholar
  16. D. K. Baek, T. J. Ko, and H. S. Kim, “Optimization of feedrate in a face milling operation using a surface roughness model,” International Journal of Machine Tools and Manufacture, vol. 41, no. 3, pp. 451–462, 2001. View at Publisher · View at Google Scholar · View at Scopus
  17. K. Palanikumar, L. Karunamoorthy, and R. Karthikeyan, “Assessment of factors influencing surface roughness on the machining of glass fiber-reinforced polymer composites,” Materials and Design, vol. 27, no. 10, pp. 862–871, 2006. View at Publisher · View at Google Scholar · View at Scopus
  18. N. S. Kumar, A. Shetty, A. Shetty, K. Ananth, and H. Shetty, “Effect of spindle speed and feed rate on surface roughness of carbon steels in CNC turning,” Procedia Engineering, vol. 38, pp. 691–697, 2012, Proceedings of the International Conference on Modelling, Optimisation and Computing (ICMOC '12). View at Publisher · View at Google Scholar
  19. J. A. Ghani, I. A. Choudhury, and H. H. Hassan, “Application of Taguchi method in the optimization of end milling parameters,” Journal of Materials Processing Technology, vol. 145, no. 1, pp. 84–92, 2004. View at Publisher · View at Google Scholar · View at Scopus