Table of Contents Author Guidelines Submit a Manuscript
Journal of Applied Mathematics
Volume 2014, Article ID 192891, 7 pages
http://dx.doi.org/10.1155/2014/192891
Research Article

Improving the Validity of Squeeze Film Air-Damping Model of MEMS Devices with Border Effect

Cheng Bai1,2 and Jin Huang1,3

1Research Institute on Mechatronics, Xidian University, Xi’an 710071, China
2Xi’an Communication Institute, Xi’an 710106, China
3Key Laboratory of Electronic Equipment Structure Design, Xidian University, Ministry of Education, Xi’an 710071, China

Received 21 February 2014; Revised 6 May 2014; Accepted 14 May 2014; Published 26 May 2014

Academic Editor: Ricardo Perera

Copyright © 2014 Cheng Bai and Jin Huang. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. M. Bao and H. Yang, “Squeeze film air damping in MEMS,” Sensors and Actuators A: Physical, vol. 136, no. 1, pp. 3–27, 2007. View at Publisher · View at Google Scholar · View at Scopus
  2. G. Schrag and G. Wachutka, “Physically based modeling of squeeze film damping by mixed-level system simulation,” Sensors and Actuators A: Physical, vol. 97-98, pp. 193–200, 2002. View at Publisher · View at Google Scholar · View at Scopus
  3. M. Andrews, I. Harris, and G. Turner, “A comparison of squeeze-film theory with measurements on a microstructure,” Sensors and Actuators A: Physical, vol. 36, no. 1, pp. 79–87, 1993. View at Google Scholar · View at Scopus
  4. F. Pan, J. Kubby, E. Peeters, A. T. Tran, and S. Mukherjee, “Squeeze film damping effect on the dynamic response of a MEMS torsion mirror,” Journal of Micromechanics and Microengineering, vol. 8, no. 3, pp. 200–208, 1998. View at Publisher · View at Google Scholar · View at Scopus
  5. A. Minikes, I. Bucher, and G. Avivi, “Damping of a micro-resonator torsion mirror in rarefied gas ambient,” Journal of Micromechanics and Microengineering, vol. 15, no. 9, pp. 1762–1769, 2005. View at Publisher · View at Google Scholar · View at Scopus
  6. A. K. Pandey, R. Pratap, and F. S. Chau, “Analytical solution of the modified Reynolds equation for squeeze film damping in perforated MEMS structures,” Sensors and Actuators A: Physical, vol. 135, no. 2, pp. 839–848, 2007. View at Publisher · View at Google Scholar · View at Scopus
  7. S. S. Mohite, H. Kesari, V. R. Sonti, and R. Pratap, “Analytical solutions for the stiffness and damping coefficients of squeeze films in MEMS devices with perforated back plates,” Journal of Micromechanics and Microengineering, vol. 15, no. 11, pp. 2083–2092, 2005. View at Publisher · View at Google Scholar · View at Scopus
  8. Z. Hao, R. Clark, J. Hammer, M. Whitley, and B. Wingfield, “Modeling air-damping effect in a bulk micromachined 2D tilt mirror,” Sensors and Actuators A: Physical, vol. 102, no. 1-2, pp. 42–48, 2002. View at Publisher · View at Google Scholar · View at Scopus
  9. T. Veijola, A. Pursula, and P. Råback, “Extending the validity of squeezed-film damper models with elongations of surface dimensions,” Journal of Micromechanics and Microengineering, vol. 15, no. 9, pp. 1624–1636, 2005. View at Publisher · View at Google Scholar · View at Scopus
  10. R. B. Darling, C. Hivick, and J. Xu, “Compact analytical modeling of squeeze film damping with arbitrary venting conditions using a Green's function approach,” Sensors and Actuators A: Physical, vol. 70, no. 1-2, pp. 32–41, 1998. View at Google Scholar · View at Scopus
  11. T. Veijola, K. Ruokonen, and I. Tittonen, “Compact model for the squeezed-film damping including the open border effects,” in Proceedings of the 4th International Conference on Modeling and Simulation of Microsystems (MSM '01), pp. 76–79, Hilton Head Island, SC, USA, March 2001. View at Scopus
  12. P. K. Kundu and I. M. Cohen, Fluid Mechanice, Academic Press, Waltham, Mass, USA, 4th edition, 2012.