Extraction and Physicochemical Characterization of Mucilage from<i> Opuntia cochenillifera</i> (L.) Miller

Monrroy, Mariel; García, Erick; Ríos, Katherine; García, José Renán

doi:https://doi.org/10.1155/2017/4301901

Journal of Chemistry

On this page

Abstract Introduction Experimental Results and Discussion Conclusion Conflicts of Interest Acknowledgments References Copyright Related Articles

Research Article | Open Access

Volume 2017 | Article ID 4301901 | https://doi.org/10.1155/2017/4301901

Extraction and Physicochemical Characterization of Mucilage from Opuntia cochenillifera (L.) Miller

Mariel Monrroy,^1,2Erick García,^1,2Katherine Ríos,^1,2and José Renán García^1,2

Academic Editor: Patricia Valentao

Received29 Dec 2016

Revised01 Apr 2017

Accepted10 Apr 2017

Published10 May 2017

Abstract

The aim of this study was to extract mucilage from O. cochenillifera (L.) cacti and determine its functional and physicochemical properties. The best mucilage yield (31%) was obtained by nonthermal extraction with hydration. The mucilage has appreciable carbohydrate and protein contents. The phytochemical analysis shown the presence of alkaloids and terpenes/steroids. The Fourier transformed infrared (FT-IR) spectrum of the mucilage exhibits typical bands for carbohydrates as O–H, C–H, and –COO⁻. The mucilage demonstrated water- and oil-holding capacities of 2.78 g water/g dry mucilage and 1.80 g oil/g dry mucilage, respectively, these properties can have a positive effect on the texture of the products when used as a stabilizer. The mildly acidic pH (4.8–5) contributes to its emulsifying capacity. The presence of electrolytes in the mucilage can be of great value in flocculation processes. The mucilage forms low viscosity solutions in the same manner as gum Arabic. Finally, its potential for use as a textile dye remover was evaluated, achieving a 70% removal rate from aqueous solutions. The prepared mucilage exhibits properties that recommend it as a natural material that can be used as an additive in the chemical, food, pharmaceuticals and cosmetics industries, as well as in decontamination processes.

1. Introduction

Opuntia spp. are flowering plants belonging to the Cactaceae family. They grow naturally in tropical and semitropical regions [1], and their cultivation is well known, especially in Mexico, Argentina, Peru, Bolivia, Brazil, Chile, the United States (Texas), Spain, Italy, Africa (Morocco, Tunisia, Eritrea, and Ethiopia), Israel, and South Africa [2]. Traditionally, the Opuntia have been used for both medicinal and edible purposes. Research has shown that extracts from their pads can reduce cholesterol levels [3] and exhibit hypoglycemic effects [4], antiulcer activity [5], neuroprotective effects [6], and anti-inflammatory and analgesic properties [5, 7]. Furthermore, these Cactaceae are characterized by their hydrocolloid properties, having a high capacity to retain water under adverse weather conditions due largely to one of their main functional components, mucilage [1, 2].

Mucilage is a complex polymeric substance composed mainly of carbohydrates with highly branched structures, which include L-arabinose, D-galactose, L-rhamnose, D-xylose, and galacturonic acid in various proportions [8]. It also contains glycoproteins [9] and other substances such as tannins, alkaloids, and steroids [1]. The mucilage composition differs among the various Opuntia spp. and the regions in which they grow [1, 2]. In addition to the aforementioned medicinal activities for these cacti, which are associated with this complex material, the ability of mucilage to form molecular networks and retain large amounts of water makes it a potential source of hydrocolloids for the chemical and cosmetics industries. Several studies have evaluated its uses in water purification/filtration [2, 9], as an adhesive lime [Ca(OH)₂] [3], emulsifying agent [10], or flocculant [11], and as an enhancer of water infiltration in soils, due to its physical properties (viscosity, elasticity, texture, and emulsifier) [12]. Other mucilage applications include its use in foods as a stabilizer, flavoring agent, fat substitute [2], and edible coating to extend the useful life of fruit [13].

Most studies on the physical and chemical properties of Opuntia mucilage have focused on O. ficus-indica, and there is little scientific information on the characteristics of other Opuntia spp. such as O. cochenillifera. Among the meritorious attributes of O. cochenillifera are its hypoglycemic effects [4] and the ability to decolorize water [14]. Consequently, this research will focus on optimizing the extraction of the mucilage from O. cochenillifera (L.) Miller and its physicochemical characterization. The mucilage thus obtained could be a natural, economical alternative functional material for use in many industrial processes.

2. Experimental

2.1. Raw Material

Fresh cladodes of O. cochenillifera were harvested from Universidad Autónoma de Chiriquí-Panamá (8°25′49.51′′N y 82°26′53.36′′W). The cladodes had an average size of 7.67 cm × 18.15 cm. Moisture content was determined after drying at 105°C for 24 h. The specimen was identified by Professor Rafael Rincón at the Herbarium of Universidad Autónoma de Chiriquí (code: UCH). A voucher specimen (number: 006757) was deposited in the Herbarium.

2.2. Extraction of Mucilage

2.2.1. Thermal Extraction of Fresh Cladodes

The cladodes were peeled, cut into pieces (2 × 2 cm²), crushed, and homogenized in a ratio of 7.5 g in 15 ml distilled water. This ratio was equivalent to suspending 100 mg dry basis in 5 ml water. Samples were placed in a water bath at different temperatures for various reaction times (Table 1) and then filtered. The mucilage was precipitated by adding 45 mL ethanol and dried in an oven at 60°C.

2.2.2. Thermal Extraction of Dried Cladodes

The cladodes were cut into pieces (2 × 2 cm²), dried at 60°C for 48 h, and milled. Then, the mucilage was extracted by mixing 100 mg of the milled sample with 5 mL water for different temperatures (44–86°C, ) and times (54–96 min, ) (Table 1). The mucilage was precipitated by adding 15 mL ethanol and dried in an oven at 60°C.

The influence of the variables and for both types of extraction was determined using response surface methodology (RSM) and multiple linear regression methods. The optimum conditions for extracting the mucilage were obtained as the maximum values of the response surface by the SIMPLEX method. The generation and evaluation of the experimental designs were carried out with the program Modde 7.0.0.1 (Umetrics, USA). Statistical validation was performed using one-way analysis of variance ANOVA with a confidence level of 95%. The models obtained were based on a circumscribed central composite design made of a factorial design and star points.

2.2.3. Extraction by Hydration

A solution was prepared by mixing the milled sample (100 mg) with water (5 mL) and allowing it to stand for 24 h. Then, the solution was filtered and the mucilage was precipitated by adding 15 mL ethanol and dried in an oven at 60°C.

2.2.4. Extraction by Agitation

A solution was prepared as described in the preceding section, stirred for 30 min using a magnetic stirrer, and then filtered. The mucilage was precipitated by adding 15 mL ethanol for 30 min and dried in an oven at 60°C.

2.2.5. Extraction by Agitation and Hydration

In this extraction, the sample was hydrated and agitated as in the previous sections.

All extractions were performed in triplicate. The results were analyzed using ANOVA and Tukey’s honest significant difference (HSD) multiple comparison test ().

2.3. Chemical Characterization of the Mucilage

The total carbohydrate content was determined by the phenol-sulfuric acid method, and the visible absorption of the resulting solution was measured at 490 nm (modified method of Bartkiene [15]). For the quantitative carbohydrate determination, mucilage powder (100 mg) and 2.5 N HCl (5 mL) were mixed in a test tube and placed in a water bath at 95°C for 3 h. The solution was neutralized with sodium carbonate, diluted with water (5 mL), and centrifuged. The supernatant was brought to a volume of 100 mL. Then, a portion of the sample (0.1 mL) was added to 5% phenol (1 mL) and concentrated sulfuric acid (5 mL), vortexed for 1 min, and placed in a water bath at 30°C for 20 min. Finally, the total carbohydrate content was determined by visible spectrophotometry (Vis) at a wavelength of 490 nm and quantified against a calibration curve using glucose. The total nitrogen concentration in the mucilage was determined by the Kjeldahl method. The mineral contents were quantified by atomic absorption spectroscopy. All analyses were performed in triplicate.

The mucilage was subjected to a phytochemical screening using the following tests: the Salkowski test for sterols; the Shinoda and sodium hydroxide tests for flavonoids; the Dragendorff, Wagner, and Mayer tests for alkaloids; the ferric chloride test for tannins; the Rosenthaler test for saponins; and the Dimroth test for 5-hydroxy flavones. A thin-layer chromatography (TLC) was used in the analysis of alkaloids. TLC was performed on 10 × 3 cm silica gel plates with a fluorescent indicator at 254 nm (Applichem, USA). Chloroform/methanol (9 : 1), chloroform (100%), and ethyl acetate/methanol/chloroform/hexane (6 : 1 : 2 : 1) were used as mobile phases. Mucilage sample was dissolved in methanol/chloroform (1 : 1), macerated for 24 hours, and then centrifuged. Solution (25 μL) was carefully layered at 1 cm from the bottom of the plate. After the separation, plates were dried at 60°C for 5 min. Then drying, the spots on the developed plates were visualized at 254 nm and also revealed with Dragendorff and Wagner reagents. A meter rule was used to measure the distance moved by the solvent and distance moved by spot, from which the retention factor (Rf values) of the spots was calculated.

Infrared spectra of the mucilage were measured by direct transmittance using the KBr pellet technique. Spectra were recorded between 4000 and 500 cm⁻¹, using a Shimadzu IRAffinity-1 Fourier-transform infrared spectrometer (FT-IR) equipped with a deuterated L-alanine doped triglycine sulfate (DLATGS) detector. The background used for the FT-IR measurements was a KBr pellet that contained no sample. All spectra were measured at a spectral resolution of 2 nm and 32 scans were taken per sample.

2.4. Physical Characterization of the Mucilage

The conductivity, pH, density, and viscosity were determined in mucilage solutions of 1, 4, and 6% (w/v), prepared by dissolving the mucilage powder in distilled water. Conductivity was determined using a conductometer and the pH with a pH meter (Mettler–Toledo, USA). The density was determined using a glass pycnometer. The viscosity of the samples, measured with a calibrated Cannon-Fenske glass capillary viscometer (Cannon Instrument Co., State College, PA, USA), was determined as the time required for the sample to flow under gravity through the device. All tests were performed in triplicate.

The water-holding capacity (WHC) and oil-holding capacity (OHC) were determined according to the methods of Chau et al. [16] and Thanatcha and Pranee [17]. A mucilage powder sample (0.2 g) was mixed in 10 mL distilled water or olive oil by vortexing for 1 min and centrifuged at 2200 rpm for 30 min. Then, the supernatant was removed and weighed. The WHC was expressed as the grams water held per gram sample, and the OHC as the grams oil held per gram sample.

2.5. Decolorization of a Textile Dye Solution

Different amounts of mucilage (0.1, 0.2, or 0.3 g) were mixed with separate green and blue dye solutions (10 mL, 100 ppm, Dylon Fabric Dye) by vortexing for 3 min and then centrifuged at 3000 rpm for 5 min. The supernatants were removed and subjected to absorbance measurements by Vis spectrophotometry at 586 nm (green) and 400 nm (blue). The percentage removal of the dye solution was then determined.

3. Results and Discussion

The mucilage content in a cladode is directly related to the moisture content because its heteropolysaccharide components have the ability to absorb water. In this work, the moisture content in young cladodes was higher than in older cladodes; thus, young cladodes with an average size of 7.67 cm × 18.15 cm were employed. The moisture content in the fresh cladodes of O. cochenillifera is 92%.

As mentioned earlier, mucilage could be a natural, economical alternative material for many industrial processes; therefore, an investigation of extraction process efficiency is relevant. Different extraction processes were examined, such as thermal and nonthermal extraction (hydration and agitation).

3.1. Mucilage Extraction

The mucilage yields obtained from fresh and dried cladodes using thermal extraction varied from 22 to 25% and 20 to 33% on a dry matter basis (Table 2), respectively. From the experimental design data and mucilage percentage obtained under each condition (Table 4), quadratic polynomials were determined (see (1)) for the fresh and dried cladodes, respectively, and validated by the ANOVA test.where is time and temperature.

In the case of the fresh cladodes, the linear term for time has a positive coefficient, meaning that the mucilage extraction increases with time. The positive quadratic terms indicates that large variation of time in either direction will result in extraction yield increase (the response surface shows a minimum). However, the linear term for temperature has no effect on mucilage yield, but considering the confidence intervals, the interaction between both variables has a significant effect on mucilage extraction. For the dried cladodes, the linear term for the temperature has a negative coefficient, meaning that the extraction yield increased as the temperature declined. The positive quadratic terms indicates that large variation of temperature in either direction will result in extraction yield increase. Time appears to have no significant effect on mucilage extraction for the range studied (50–80 min). Considering the confidence intervals, the interactions between variables have no significant effect on mucilage extraction.

Error values corresponded to a 95% confidence level. The effects of the extraction conditions on the mucilage yield are shown in the response surface graph for the polynomials (within the studied variable ranges) (Figures 1(a) and 1(b)). The responses are close to the experimental values, with correlation coefficients () of 0.93 and 0.89 for the fresh and dry cladodes, respectively.

(a)

(b)

The optimum values of the variables for the maximal mucilage yields were determined by the SIMPLEX method using the maximum values of the response surface. The maximum mucilage yields predicted for the fresh and dried cladodes are % and %. The predicted values of the best extraction variables are 54 min and 80°C for the fresh cladodes and 86 min and 44°C for the dried cladodes. The experimental mucilage yields for the fresh and dried cladodes obtained under these conditions are % and %, respectively, which agree well with the predicted values. Mucilage extraction from the dried cladodes was better than from the fresh cladodes, which may be related to the larger surface area of the former, which would improve the extraction process.

The nonthermal methods of extraction from the cladodes were based on hydration, agitation, and hydration and agitation processes. Table 3 shows the mucilage yields obtained for the three approaches. Increased performance is observed for the samples subjected to the hydration and hydration/agitation processes, compared to agitation alone. This indicates that the hydration process is very important when mucilage extraction is performed with previously dried and powdered cladode samples. The results obtained were analyzed using ANOVA and Tukey’s HSD multiple comparison test (), which showed that there is a significant difference between the mean of the agitation process with the other two processes at the 95% confidence level.

The maximum mucilage extraction yields obtained from cladodes under the thermal and nonthermal extraction methods in this study are similar and/or higher than those reported for other Opuntia such as O. streptacantha (7.2%), O. megacantha (7.4%), O. albicarpa (6.9%), O. milpa alta (7%), O. dillenii (16%), and O. ficus-indica (4–25%) [8, 18–20].

3.2. Chemical Characterization of the Mucilage

The total carbohydrate content was 40%, which is higher than that reported for O. dillenii, with 12 to 15% as polysaccharides [20], but within the range given for O. ficus-indica (13–64%) [21, 22]. In addition, the mucilage is an excellent source of essential minerals such as calcium, phosphorus, magnesium, iron, potassium, zinc, and copper (Table 4). Calcium is the most abundant mineral in the mucilage, which agrees with other studies of cactus pads [23–25]. For example, O. ficus-indica was a better source of calcium than spinach, soy, and grains, suggesting that Opuntia spp. may have potential in the prevention and treatment of diseases such as osteoporosis [26]. Because of their excellent nutritional qualities, Opuntia (especially O. indica) have been used as food sources in countries such as Mexico. As the O. cochenillifera mucilage is a rich source of carbohydrates and essential minerals, it has good potential for use as a nutritional supplement.

The crude protein content was determined as 7.4%. This value is comparable to those reported for O. ficus-indica cladodes (5–9%) but higher than those in O. stricta (5%) and guar gum (3–5%) [1, 27, 28]. The interactions that occur through the specific (hydrophilic) functional groups of polysaccharides and proteins are an important factor in the study of mucilage proteins; these form a three-dimensional network that can improve the stability and uniformity of the system matrix and suggest potential application in the industry [29]. Usually, proteins and polysaccharides are safe food additives that can form physically stable emulsions [30].

The phytochemical analysis shown in Table 5 reveals the presence of alkaloids by the Dragendorff, Mayer, and Wagner tests, which identify quaternary alkaloids and/or amine-oxides. The TLC analysis also revealed the presence of alkaloids; two spots were visualized at 254 nm (Figure 2), using different mixtures of eluents. Ethyl acetate/methanol/chloroform/hexane (6 : 1 : 2 : 1) is the best eluent employed, showing Rf values 0.88 and 0.63, respectively (Table 6). Likewise, two spots were observed with Dragendorff and Wagner reagents. The presence of terpenes/steroids was also found using the Salkowski test. Although the presence of saponins, flavonoids, and tannins was not found in this study, Tomás Ch et al. [31] reported the presence of saponins, flavonoids, and alkaloids in the pulp of O. ficus-indica. The chemical composition of the Opuntia spp. is quite variable, depending on a number of factors such as the chemical characteristics of the soil, geographical location, environmental conditions, age, and species [8, 22, 27].

The FT-IR spectrum of the mucilage exhibits typical bands for Opuntia spp. The functional group bands found in the O. cochenillifera mucilage (Figure 3) are characteristic for proteins and polysaccharides. The bands at 3420, 2931, and 1623 cm⁻¹ represent the stretching vibrations of O–H, C–H, and –COO⁻ (asymmetric vibrations) groups, respectively, in carbohydrate and uronic acid molecules. Further, the bands at 2931 and 1623 cm⁻¹ appear to be associated with the N–H stretching and bending motions, respectively, of proteins. Han et al. [20] and Contreras-Padilla et al. [18] reported bands at 3500–3200 cm⁻¹ corresponding to carbohydrate O–H bonds in O. dillenii and O. ficus-indica mucilage. Also, they assigned a band around 2920 cm⁻¹ to the C–H stretching vibration of the pyranose group. Zhao et al. [32] attributed the bands at 1620, 1596, and 1420 cm⁻¹ to deprotonated carboxylic acid groups (–COO⁻) in uronic acid in O. monacantha. Similar bands are observed at 1623, 1582, and 1431 cm⁻¹ in our spectrum. The bands found at ~1431–1264 cm⁻¹ can be assigned to C–O stretching and O–H deformation vibrations, according to Han et al. [20] and the bands at 1431–1393 cm⁻¹ indicate C–N stretching modes [33]. The bands at 1085 and 1045 cm⁻¹ indicate the presence of monosaccharides such as mannose and glucose in pyranose ring conformations [20, 34]. The absorption band at 893 cm⁻¹ corresponds to β-D-glucose [32]. The bands at 774 and 608 cm⁻¹ are attributed to N–H and O–H out-of-plane vibrations, respectively [32, 33].

3.3. Physical Characterization of the Mucilage

3.3.1. pH, Conductivity, Density, and Viscosity Measurements

The functional properties of mucilage can be affected by its chemical composition. The mucilage densities at concentrations of 1, 4, and 6% are 1.03, 1.03, and 1.05 g·mL⁻¹, respectively. These values are higher than those reported for O. ficus-indica (0.85 g·mL⁻¹) and O. stricta (0.81 g·mL⁻¹) at concentrations of 8% [1]. However, the density obtained for the O. cochenillifera mucilage is comparable to those reported for gum arabic (1.00–1.02 g mL⁻¹) at the same concentrations [35]. Gum arabic is the most utilized type of gum in food and other industrial applications because of its good emulsifying and stabilizing properties.

The conductivities of the obtained mucilage solutions are lower than those reported in the literature for O. ficus-indica but comparable to O. stricta [1]. The conductivity values for samples prepared at concentrations of 1, 4, and 6% are 2.3, 4.9, and 6.4 mS cm⁻¹, respectively. Variations in the conductivity at different concentrations may be attributed to the presence of greater numbers of divalent and monovalent ions, which increase the conductivity, as has been reported for the O. ficus-indica mucilage [1]. According to Gebresamuel and Gebre-Mariam [1], the presence of electrolytes in the mucilage can be of value in the flocculation of suspension formulations.

The pH measurements reveal that the mucilage at different concentrations is slightly acidic (4.8–5.0). This acidic nature indicates that the mucilage contains uronic acids in its structure. The pH values are lower than those found by Contreras-Padilla et al. [18] for O. ficus-indica (5.5–6) but comparable to those reported for gum arabic (4.5–5.6) [36, 37]. The pH is also a critical factor in coagulation/flocculation processes, wherein the optimal pH should be between 5 and 7.5 [38].

The mucilage viscosities for solutions of 1 and 4% are 1.6 and 4.6 mPa·s, respectively. These values are comparable to those for 1 and 4% solutions of pure gum arabic (1.3 and 2.4 mPa·s, resp.) [35]. This ability of mucilage to form low viscosity solutions at low concentrations in the same manner as gum arabic should enable it to form solutions in a wide range of concentrations with excellent properties as an emulsifier and stabilizer.

3.3.2. Water- and Oil-Holding Capacities

O. cochenillifera mucilage presents a better WHC (2.78 g water/g dry mucilage) than OHC (1.80 g oil/g dry mucilage). The WHC influences the formation of viscous solutions that can facilitate industrial processes. Mucilage forms a three-dimensional network in contact with water, trapping it and resulting in highly viscous solutions. Mucilage is primarily composed of galactose, mannose, xylose, and other sugars, and, thus, has a high capacity to bind or retain water, similarly to pectins, gums, and some algal polysaccharides. Because of this large water absorption capacity, mucilage may find applications in foods, cosmetics, and pharmaceuticals, in which it can dissolve, be dispersed, and form colloids [13]. Similarly, mucilage can be used to modify the rheological properties of soil, acting as a binding agent in soil aggregation [2, 12]. The OHC would allow its use in combination with other products to collect petroleum and various oils in case of spills on water. In addition, the good OHC value suggests that mucilage could improve the texture of food products.

3.4. Removal of Textile Dyes as a Sample Application

Mucilage has the potential to be used in the clarification of water due to its ability to retain different types of particles that are dispersed therein [9]. Additionally, as a negatively charged polyelectrolytic molecule due mainly to its sugar composition, mucilage has the ability to attract or retain certain types of positively charged substances. As demonstrated in this investigation, the capacity of the O. cochenillifera mucilage to remove textile dyes from aqueous solutions is considerable (Figures 4(a) and 4(b)). The removal percentage varied depending on the mucilage concentration and the dye, with maximum values of 73% and 49% for the green and blue dyes, respectively, at a concentration of 3% mucilage. These results agree with those reported by Peláez-Cid et al. [39] in which 5–95% of the textile dyes were removed from aqueous solutions using O. ficus-indica fruit waste as an adsorbent. According to Anjaneyulu et al. [40] adsorption methods for the removal of dyes are based on the high affinity of the dyes. Adsorptive bleaching is influenced by several factors, such as the physicochemical dye-adsorbent interactions, adsorbent surface area, particle size, temperature, and contact time.

(a)

(b)

O. cochenillifera mucilage can be considered a low-cost biosorbent and environmentally friendly alternative for water clarification. For example, the textile industry worldwide consumes tremendous amounts of water in dyeing processes, and wastewaters from this industry are some of the most polluted across all industrial sectors. Some dyes and byproducts are carcinogens or mutagens and aesthetically deteriorate water bodies and impact flora and fauna. Zhang et al. [41] compared the ability of a mucilage clarifier with other traditional agents such as aluminum sulfate, reporting that the mucilage of O. ficus-indica demonstrated similar behavior to aluminum sulfate.

4. Conclusion

O. cochenillifera mucilage is a functional plant-derived material that has potential applications in the pharmaceutical and chemical industries. It is a rich source of carbohydrates, proteins, and minerals and can be considered nontoxic and safe for humans. Indeed, several cultures have traditionally used the cladodes of the Opuntia spp. as food. Its density, viscosity, pH, and conductivity characteristics recommend its use as an additive in the formulation of food and drugs. O. cochenillifera mucilage could be a good alternative emulsifier and stabilizing agent. Finally, the mucilage from O. cochenillifera could be considered a natural technological alternative in many processes of decontamination for its ability to remove dyes.

Conflicts of Interest

The authors declare that they have no conflicts of interest.

Acknowledgments

Financial support was received from National Secretariat of Science, Technology, and Innovation (SENACYT) as member of the Panamá Research National System (SNI). The authors would like to thank staff at the Herbarium of Universidad Autónoma de Chiriquí (UNACHI) for the identification of the Opuntia sp. and Dr. Viviana Morales of the Research Center for Natural Products and Biotechnology of UNACHI for her support with the analysis of alkaloids.

References

N. Gebresamuel and T. Gebre-Mariam, “Comparative physico-chemical characterization of the mucilages of two cactus pears (Opuntia spp.) obtained from Mekelle, Northern Ethiopia,” Journal of Biomaterials and Nanobiotechnology, vol. 3, pp. 79–86, 2012.
View at: Google Scholar
C. Sáenz, E. Sepúlveda, and B. Matsuhiro, “Opuntia spp. mucilage's: a functional component with industrial perspectives,” Journal of Arid Environments, vol. 57, no. 3, pp. 275–290, 2004.
View at: Publisher Site | Google Scholar
A. Cárdenas, W. M. Arguelles, and F. M. Goycoolea, “On the possible role of opuntia ficus-indica mucilage in lime mortar performance in the protection of historical buildings,” Journal of the Professional Association for Cactus Development, vol. 3, 1998.
View at: Google Scholar
A. Andrade-Cetto and M. Heinrich, “Mexican plants with hypoglycaemic effect used in the treatment of diabetes,” Journal of Ethnopharmacology, vol. 99, no. 3, pp. 325–348, 2005.
View at: Publisher Site | Google Scholar
E. M. Galati, M. T. Monforte, M. M. Tripodo, A. D'Aquino, and M. R. Mondello, “Antiulcer activity of Opuntia ficus indica (L.) Mill. (Cactaceae): ultrastructural study,” Journal of Ethnopharmacology, vol. 76, no. 1, pp. 1–9, 2001.
View at: Publisher Site | Google Scholar
H. Dok-Go, K. H. Lee, H. J. Kim et al., “Neuroprotective effects of antioxidative flavonoids, quercetin, (+)-dihydroquercetin and quercetin 3-methyl ether, isolated from Opuntia ficus-indica var. saboten,” Brain Research, vol. 965, no. 1-2, pp. 130–136, 2003.
View at: Publisher Site | Google Scholar
J. F. Loro, I. Del Rio, and L. Pérez-Santana, “Preliminary studies of analgesic and anti-inflammatory properties of Opuntia dillenii aqueous extract,” Journal of Ethnopharmacology, vol. 67, no. 2, pp. 213–218, 1999.
View at: Publisher Site | Google Scholar
E. Sepúlveda, C. Sáenz, E. Aliaga, and C. Aceituno, “Extraction and characterization of mucilage in Opuntia spp.,” Journal of Arid Environments, vol. 68, no. 4, pp. 534–545, 2007.
View at: Publisher Site | Google Scholar
T. Pichler, K. Young, and N. Alcantar, “Eliminating turbidity in drinking water using the mucilage of a common cactus,” Water Science & Technology, vol. 12, no. 2, pp. 179–186, 2012.
View at: Google Scholar
N. Garti, “Hydrocolloids as emulsifying agents for oil-in-water emulsions,” Journal of Dispersion Science and Technology, vol. 20, no. 1-2, pp. 327–355, 1999.
View at: Publisher Site | Google Scholar
K. A. Young, A. Anzalone, T. Pichler, M. Picquart, and N. A. Alcantar, “The mexican cactus as a new environmentally benign material for the removal of contaminants in drinking water,” MRS Online Proceedings Library, vol. 930, 2006.
View at: Google Scholar
D. Gardiner, P. Felker, and T. Carr, “Cactus extract increases water infiltration rates in two soils,” Communications in Soil Science and Plant Analysis, vol. 30, no. 11-12, pp. 1707–1712, 1999.
View at: Publisher Site | Google Scholar
V. Del-Valle, P. Hernández-Muñoz, A. Guarda, and M. J. Galotto, “Development of a cactus-mucilage edible coating (Opuntia ficus indica) and its application to extend strawberry (Fragaria ananassa) shelf-life,” Food Chemistry, vol. 91, no. 4, pp. 751–756, 2005.
View at: Publisher Site | Google Scholar
J. Jiménez, M. Vargas, and N. Quirós, “Estimation of the nopal cactus (Opuntia cochenillifera) for color removal in drinking water,” Tecnología en Marcha, vol. 25, no. 4, pp. 55–62, 2012.
View at: Google Scholar
E. Bartkiene, Método Fenol-Ácido Sulfúrico Plant Food Analysis Methods Kaunas, Lituania, Unión Europea, Kaunas, Lituania, 2012.
C.-F. Chau, P. C. K. Cheung, and Y.-S. Wong, “Functional properties of protein concentrates from three chinese indigenous legume seeds,” Journal of Agricultural and Food Chemistry, vol. 45, no. 7, pp. 2500–2503, 1997.
View at: Publisher Site | Google Scholar
R. Thanatcha and A. Pranee, “Extraction and characterization of mucilage in ziziphus mauritiana lam,” International Food Research Journal, vol. 18, pp. 201–212, 2011.
View at: Google Scholar
M. Contreras-Padilla, M. E. Rodríguez-García, E. Gutiérrez-Cortez, M. d. C. Valderrama-Bravo, J. I. Rojas-Molina, and E. M. Rivera-Muñoz, “Physicochemical and rheological characterization of Opuntia ficus mucilage at three different maturity stages of cladode,” European Polymer Journal, vol. 78, pp. 226–234, 2016.
View at: Google Scholar
L. Felkai-Haddache, F. Dahmoune, H. Remini, K. Lefsih, L. Mouni, and K. Madani, “Microwave optimization of mucilage extraction from Opuntia ficus indica Cladodes,” International Journal of Biological Macromolecules, vol. 84, pp. 24–30, 2016.
View at: Publisher Site | Google Scholar
Y.-L. Han, J. Gao, Y.-Y. Yin, Z.-Y. Jin, X.-M. Xu, and H.-Q. Chen, “Extraction optimization by response surface methodology of mucilage polysaccharide from the peel of Opuntia dillenii haw. fruits and their physicochemical properties,” Carbohydrate Polymers, vol. 151, pp. 381–391, 2016.
View at: Publisher Site | Google Scholar
J. H. Cota-Sánchez, “Nutritional composition of the prickly pear (Opuntia ficus-indica) fruit,” in Nutritional Composition of Fruit Cultivars, M. S. J. Simmonds and V. R. Preedy, Eds., chapter 28, pp. 691–712, Academic Press, San Diego, Calif, USA, 2016.
View at: Google Scholar
T. Nharingo and M. Moyo, “Application of Opuntia ficus-indica in bioremediation of wastewaters. A critical review,” Journal of Environmental Management, vol. 166, pp. 55–72, 2016.
View at: Publisher Site | Google Scholar
L. P. Méndez, F. T. Flores, J. D. Martín, E. M. Rodríguez Rodríguez, and C. Díaz Romero, “Physicochemical characterization of cactus pads from Opuntia dillenii and Opuntia ficus indica,” Food Chemistry, vol. 188, pp. 393–398, 2015.
View at: Publisher Site | Google Scholar
M. E. Rodríguez-García, C. de Lira, E. Hernández-Becerra et al., “Physicochemical characterization of nopal pads (Opuntia ficus indica) and dry vacuum nopal powders as a function of the maturation,” Plant Foods for Human Nutrition, vol. 62, no. 3, pp. 107–112, 2007.
View at: Publisher Site | Google Scholar
C. Sáenz, E. Sepúlveda, N. Pak, and M. Lecaros, “Chemical and physical characterization of cactus cladode (Opuntia ficus-indica) powder,” Italian Journal of Food Science, vol. 22, no. 4, pp. 416–422, 2010.
View at: Google Scholar
M. I. Hernández-Urbiola, M. Contreras-Padilla, E. Pérez-Torrero et al., “Study of nutritional composition of nopal (Opuntia ficus indica cv. Redonda) at different maturity stages,” The Open Nutrition Journal, vol. 4, pp. 11–16, 2010.
View at: Google Scholar
M. I. Hernández-Urbiola, E. Pérez-Torrero, and M. E. Rodríguez-García, “Chemical analysis of nutritional content of prickly pads (Opuntia ficus indica) at varied ages in an organic harvest,” International Journal of Environmental Research and Public Health, vol. 8, no. 5, pp. 1287–1295, 2011.
View at: Publisher Site | Google Scholar
S. Murwan, A. Abdelwahab, and N. Sulafa, “Quality assessment of guar gum (endosperm) of guar (Cyamopsis tetragonoloba),” ISCA Journal of Biological Sciences, vol. 1, no. 1, pp. 67–70, 2012.
View at: Google Scholar
F. Rincón, G. León de Pinto, O. Beltrán, C. Clamens, and R. Guerrero, “Funcionalidad de una mezcla de gomas de acacia glomerosa, enterolobium cyclocarpum e hymenaea courbaril en la preparación de helados de bajo contenido calórico,” Revista Científica, vol. 18, pp. 87–92, 2008.
View at: Google Scholar
P. K. Chityala, H. Khouryieh, K. Williams, and E. Conte, “Effect of xanthan/enzyme-modified guar gum mixtures on the stability of whey protein isolate stabilized fish oil-in-water emulsions,” Food Chemistry, vol. 212, pp. 332–340, 2016.
View at: Publisher Site | Google Scholar
G. Tomás Ch, J. Huamán M, R. Aguirre M et al., “Estudio qímico y fitoquímico de la Opuntia ficus-indica “tuna”, y elaboración de un alimento funcional,” Revista Peruana de Química e Ingeniería Química, vol. 15, no. 1, article 5, 2012.
View at: Google Scholar
M. M. Zhao, N. Yang, B. Yang, Y. Jiang, and G. Zhang, “Structural characterization of water-soluble polysaccharides from Opuntia monacantha cladodes in relation to their anti-glycated activities,” Food Chemistry, vol. 105, no. 4, pp. 1480–1486, 2007.
View at: Publisher Site | Google Scholar
B. Smith, Infrared Spectral Interpretation: A Systematic Approach, CRS Press LLC, Boca Raton, Fla, USA, 1999.
F. Nejatzadeh-Barandozi and S. T. Enferadi, “FT-IR study of the polysaccharides isolated from the skin juice, gel juice, and flower of Aloe vera tissues affected by fertilizer treatment,” Organic and Medicinal Chemistry Letters, vol. 2, no. 1, article 33, 2012.
View at: Publisher Site | Google Scholar
R. L. Whistler, Industrial Gums, Polysaccharides and Their Derivatives, Academic Press Inc, New York, NY, USA, 2nd edition, 1973.
A. Abu Baker, A. Tahir, and M. K. Sabah Elkheir, “Effect of tree and nodule age on some physicochemical properties of gum from acacia senegal (l.) wild., Sudan,” Research Journal of Agriculture and Biological Sciences, vol. 3, no. 6, pp. 866–870, 2007.
View at: Google Scholar
R. M. A. Daoub, A. H. Elmubarak, M. Misran, E. A. Hassan, and M. E. Osman, “Characterization and functional properties of some natural Acacia gums,” Journal of the Saudi Society of Agricultural Sciences, 2016.
View at: Google Scholar
M. Libhaber and A. Orozco, Sustainable Treatment and Reuse of Municipal Wastewater, IWA Publishing, London, UK, 2012.
A. A. Peláez-Cid, I. Velázquez-Ugalde, A. M. Herrera-González, and J. García-Serrano, “Textile dyes removal from aqueous solution using Opuntia ficus-indica fruit waste as adsorbent and its characterization,” Journal of Environmental Management, vol. 130, pp. 90–97, 2013.
View at: Publisher Site | Google Scholar
Y. Anjaneyulu, N. Sreedhara Chary, and D. Samuel Suman Raj, “Decolourization of industrial effluents —Available methods and emerging technologies—A review,” Reviews in Environmental Science and Biotechnology, vol. 4, no. 4, pp. 245–273, 2005.
View at: Publisher Site | Google Scholar
J. Zhang, F. Zhang, Y. Luo, and H. Yang, “A preliminary study on cactus as coagulant in water treatment,” Process Biochemistry, vol. 41, no. 3, pp. 730–733, 2006.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2017 Mariel Monrroy et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

16078

Downloads

4382

Citations