Table of Contents Author Guidelines Submit a Manuscript
Journal of Engineering
Volume 2014, Article ID 124247, 8 pages
http://dx.doi.org/10.1155/2014/124247
Research Article

Influence of Ultrasonic Burnishing Technique on Surface Quality and Change in the Dimensions of Metal Shafts

1Engineering Design and Production, Production Engineering, School of Science and Technology, Aalto University, Puumiehenkuja 3, 02150 Espoo, Finland
2School of Science and Technology, Aalto University, Puumiehenkuja 3, 02150 Espoo, Finland

Received 19 August 2014; Accepted 21 October 2014; Published 12 November 2014

Academic Editor: Sheng-Rui Jian

Copyright © 2014 Juha Huuki et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. A. Rodríguez, L. N. L. de Lacalle, A. Celaya, A. Lamikiz, and J. Albizuri, “Surface improvement of shafts by the deep ball-burnishing technique,” Surface and Coatings Technology, vol. 206, no. 11-12, pp. 2817–2824, 2012. View at Publisher · View at Google Scholar · View at Scopus
  2. J. Huuki and S. V. A. Laakso, “Integrity of surfaces finished with ultrasonic burnishing,” Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, vol. 227, no. 1, pp. 45–53, 2013. View at Publisher · View at Google Scholar · View at Scopus
  3. M. Hokkanen, “Ultra burnishing,” The Hiqusa Report, Tampere University of Technology, 2006, http://www.hiqusa.com/hiqusa_report.pdf. View at Google Scholar
  4. L. N. L. de Lacalle, A. Lamikiz, J. Muñoa, and J. A. Sánchez, “Quality improvement of ball-end milled sculptured surfaces by ball burnishing,” International Journal of Machine Tools and Manufacture, vol. 45, no. 15, pp. 1659–1668, 2005. View at Publisher · View at Google Scholar · View at Scopus
  5. A. M. Hassan and A. S. Al-Bsharat, “Influence of burnishing process on surface roughness, hardness, and microstructure of some non-ferrous metals,” Wear, vol. 199, no. 1, pp. 1–8, 1996. View at Publisher · View at Google Scholar · View at Scopus
  6. A. T. Bozdana, N. Gindy, and H. Li, “Deep cold rolling with ultrasonic vibrations—a new mechanical surface enhancement technique,” International Journal of Machine Tools and Manufacture, vol. 45, no. 6, pp. 713–718, 2004. View at Publisher · View at Google Scholar · View at Scopus
  7. G. D. Revankar, R. Shetty, S. S. Rao, and V. N. Gaitonde, “Selection of optimal process parameters in ball burnishing of titanium alloy,” Machining Science and Technology, vol. 18, no. 3, pp. 464–483, 2014. View at Google Scholar
  8. G. Schuetz, “Four methods of measuring out-of-roundness,” Modern Machine Shop, vol. 70, no. 3, 1997, ProQuest pg. 156. View at Google Scholar
  9. D. Jianxin and L. Taichiu, “Ultrasonic machining of alumina-based ceramic composites,” Journal of the European Ceramic Society, vol. 22, no. 8, pp. 1235–1241, 2002. View at Publisher · View at Google Scholar · View at Scopus
  10. M. H. El-Axir, O. M. Othman, and A. M. Abodiena, “Improvements in out-of-roundness and microhardness of inner surfaces by internal ball burnishing process,” Journal of Materials Processing Technology, vol. 196, no. 1–3, pp. 120–128, 2008. View at Publisher · View at Google Scholar · View at Scopus
  11. V.-B. Le and D. T. Lee, “Out-of-roundness problem revisited,” IEEE Transactions on Pattern Analysis and Machine Intelligence, vol. 13, no. 3, pp. 217–223, 1991. View at Publisher · View at Google Scholar · View at Scopus
  12. Taylor Hobson Ltd, Exploring Roundness: A Fundamental Guide to the Measurement of Cylindrical Form, Taylor Hobson Limited, Leicester, UK, 2006.
  13. J. Huuki, The use of ultra burnishing in finishing planar surfaces [Licenciate’s Thesis], Helsinki University of Technology, Espoo, Finland, 2008, (Finnish).