Table of Contents Author Guidelines Submit a Manuscript
Journal of Engineering
Volume 2015 (2015), Article ID 178652, 10 pages
http://dx.doi.org/10.1155/2015/178652
Research Article

Experimental Thermal Analysis of Diesel Engine Piston and Cylinder Wall

1Department of Mechanical Engineering, Krishna Institute of Engineering & Technology, Ghaziabad 201206, India
2Department of Mechanical Engineering, National Institute of Technology Kurukshetra, Kurukshetra 136118, India
3Department of Mechanical Engineering, Banaras Hindu University, Varanasi 221002, India

Received 1 August 2014; Accepted 19 January 2015

Academic Editor: Mariatti Jaafar

Copyright © 2015 Subodh Kumar Sharma et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. J. B. Heywood, Internal Combustion Engines Fundamentals, McGraw-Hill, New York, NY, USA, 1989.
  2. R. Stone, Introduction to Internal Combustion Engines, Macmillan Press, 1999.
  3. C. F. Taylor and T. Y. Toong, “Heat transfer in internal-combustion engines,” ASME Paper 57-HT-17, 1957. View at Google Scholar
  4. G. A. Woschni, “Universally applicable equation for the instantaneous heat transfer coefficient in the internal combustion engine,” SAE 670931, 1967. View at Google Scholar
  5. G. F. Hohenberg, “Advanced approaches for heat transfer calculation,” SAE 790825, SAE International, 1979. View at Google Scholar
  6. J. Chang, O. Guralp, Z. Filipi et al., “New heat transfer correlation for an HCCI engine derived from measurements of instantaneous surface heat flux,” SAE 2004-01-2996, 2004. View at Google Scholar
  7. S. K. Sharma, P. K. Saini, and N. K. Samria, “Modelling and analysis of radial thermal stresses and temperature field in diesel engine valves with and without air cavity,” International Journal of Engineering, Science and Technology, vol. 5, no. 3, pp. 111–123, 2013. View at Publisher · View at Google Scholar
  8. G. Borman and K. Nishiwaki, “Internal-combustion engine heat transfer,” Progress in Energy and Combustion Science, vol. 13, no. 1, pp. 1–46, 1987. View at Publisher · View at Google Scholar · View at Scopus
  9. A. Kandil, A. A. El-Kady, and A. El-Kafrawy, “Transient thermal stress analysis of thick-walled cylinders,” International Journal of Mechanical Sciences, vol. 37, no. 7, pp. 721–732, 1995. View at Publisher · View at Google Scholar · View at Scopus
  10. I. Taymaz, “An analysis of residual stresses in thermal barrier coatings: a FE performance assessment,” Plasma Processes and Polymers, vol. 6, no. 1, pp. S599–S604, 2009. View at Publisher · View at Google Scholar · View at Scopus
  11. E. Buyukkaya and M. Cerit, “Thermal analysis of a ceramic coating diesel engine piston using 3-D finite element method,” Surface and Coatings Technology, vol. 202, no. 2, pp. 398–402, 2007. View at Publisher · View at Google Scholar · View at Scopus
  12. B. Zhao, “Thermal stress analysis of ceramic-coated diesel engine pistons based on the wavelet finite-element method,” Journal of Engineering Mechanics, vol. 138, no. 1, pp. 143–149, 2012. View at Publisher · View at Google Scholar · View at Scopus
  13. M. Cerit, “Thermo mechanical analysis of a partially ceramic coated piston used in an SI engine,” Surface & Coatings Technology, vol. 205, no. 11, pp. 3499–3505, 2011. View at Publisher · View at Google Scholar · View at Scopus
  14. Y. Y. Wu, B.-C. Chen, and F.-C. Hsieh, “Heat transfer model for small-scale air-cooled spark-ignition four-stroke engines,” International Journal of Heat and Mass Transfer, vol. 49, no. 21-22, pp. 3895–3905, 2006. View at Publisher · View at Google Scholar · View at Scopus
  15. Y.-Y. Wu, B.-C. Chen, F.-C. Hsieh, and C.-T. Ke, “Heat transfer model for small-scale spark-ignition engines,” International Journal of Heat and Mass Transfer, vol. 52, no. 7-8, pp. 1875–1886, 2009. View at Publisher · View at Google Scholar · View at Scopus
  16. C. D. Rakopoulos and G. C. Mavropoulos, “Study of the steady and transient temperature field and heat flow in the combustion chamber components of a medium speed diesel engine using finite element analyses,” International Journal of Energy Research, vol. 20, no. 5, pp. 437–464, 1996. View at Google Scholar · View at Scopus
  17. D. J. Thornhill, “Experimental investigation into the temperature and heat transfer distribution around air-cooled cylinders,” Tech. Rep. 2006-32-0039, SAE, 2006. View at Google Scholar
  18. C. D. Rakopoulos, K. A. Antonopoulos, D. C. Rakapoulos, and E. G. Giakoumis, “Investigation of the temperature oscillations in the cylinder walls of a diesel engine with special reference to the limited cooled case,” International Journal of Energy Research, vol. 28, no. 11, pp. 977–1002, 2004. View at Publisher · View at Google Scholar · View at Scopus
  19. D. Descieux and M. Feidt, “One zone thermodynamic model simulation of an ignition compression engine,” Applied Thermal Engineering, vol. 27, no. 8-9, pp. 1457–1466, 2007. View at Publisher · View at Google Scholar · View at Scopus
  20. Y. Zhaoda, F. Zheng, Y. Siaoli, Y. Zhixing, and S. Hongouan, “Calculation and prediction of thermal loading of the air cooled diesel engine,” SAE 881254, SAE International, 1988. View at Google Scholar
  21. R. Prasad and N. K. Samria, “Transient heat transfer analysis in an internal combustion engine piston,” Computers & Structures, vol. 34, no. 5, pp. 787–793, 1990. View at Publisher · View at Google Scholar · View at Scopus