Table of Contents Author Guidelines Submit a Manuscript
Journal of Engineering
Volume 2016 (2016), Article ID 8487976, 5 pages
http://dx.doi.org/10.1155/2016/8487976
Research Article

Composition Design and Fatigue Curves of Hardfacing Materials for Cold Roll

1School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300132, China
2Tianjin Key Laboratory of Materials Laminating Fabrication and Interface Control Technology, Tianjin 300132, China

Received 30 November 2015; Revised 4 February 2016; Accepted 7 February 2016

Academic Editor: Sheng-Rui Jian

Copyright © 2016 C. L. Chen et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. G. Pantazopoulos and A. Vazdirvanidis, “Fractographic and metallographic study of spalling failure of steel straightener rolls,” Journal of Failure Analysis and Prevention, vol. 8, no. 6, pp. 509–514, 2008. View at Publisher · View at Google Scholar · View at Scopus
  2. H. R. B. Rad, A. Monshi, M. H. Idris, M. R. A. Kadir, and H. Jafari, “Premature failure analysis of forged cold back-up roll in a continuous tandem mill,” Materials and Design, vol. 32, no. 8-9, pp. 4376–4384, 2011. View at Publisher · View at Google Scholar · View at Scopus
  3. X.-F. Qin, D.-L. Sun, L.-Y. Xie, and Q. Wu, “Hardening mechanism of Cr5 backup roll material induced by rolling contact fatigue,” Materials Science & Engineering A, vol. 600, pp. 195–199, 2014. View at Publisher · View at Google Scholar · View at Scopus
  4. C. K. Kim, S. Lee, J.-Y. Jung, and S. Ahn, “Effects of complex carbide fraction on high-temperature wear properties of hardfacing alloys reinforced with complex carbides,” Materials Science and Engineering A, vol. 349, no. 1-2, pp. 1–11, 2003. View at Publisher · View at Google Scholar · View at Scopus
  5. D. J. Branagan, M. C. Marshall, and B. E. Meacham, “High toughness high hardness iron based PTAW weld materials,” Materials Science and Engineering A, vol. 428, no. 1-2, pp. 116–123, 2006. View at Publisher · View at Google Scholar · View at Scopus
  6. B. Venkatesh, K. Sriker, and V. S. V. Prabhakar, “Wear characteristics of hardfacing alloys: state-of-the-art,” Procedia Materials Science, vol. 10, pp. 527–532, 2015. View at Publisher · View at Google Scholar
  7. X. H. Wang, F. Han, X. M. Liu, S. Y. Qu, and Z. D. Zou, “Microstructure and wear properties of the Fe-Ti-V-Mo-C hardfacing alloy,” Wear, vol. 265, no. 5-6, pp. 583–589, 2008. View at Publisher · View at Google Scholar · View at Scopus
  8. E. O. Correa, N. G. Alcântara, L. C. Valeriano, N. D. Barbedo, and R. R. Chaves, “The effect of microstructure on abrasive wear of a Fe-Cr-C-Nb hardfacing alloy deposited by the open arc welding process,” Surface & Coatings Technology, vol. 276, pp. 479–484, 2015. View at Publisher · View at Google Scholar
  9. A. V. Khvan, B. Hallstedt, and K. Chang, “Thermodynamic assessment of Cr-Nb-C and Mn-Nb-C systems,” Calphad, vol. 39, pp. 54–61, 2012. View at Publisher · View at Google Scholar · View at Scopus
  10. Q. B. Wang, Z. X. Li, Y. W. Shi, L. Z. Wang, and F. Liu, “Interior crack and its formation mechanism in overlaying weld of back-up rolls,” Engineering Failure Analysis, vol. 34, pp. 268–277, 2013. View at Publisher · View at Google Scholar · View at Scopus
  11. C. S. Bandara, S. C. Siriwardane, U. I. Dissanayake, and R. Dissanayake, “Full range S-N curves for fatigue life evaluation of steels using hardness measurements,” International Journal of Fatigue, vol. 82, part 2, pp. 325–331, 2016. View at Publisher · View at Google Scholar
  12. Z. L. Guo, N. Saunders, P. Miodownik, and J.-P. Schille, “Modelling the strain-life relationship of commercial alloys,” in Proceedings of the ASME Pressure Vessels and Piping Conference, pp. 281–287, San Antonio, Tex, USA, July 2007. View at Publisher · View at Google Scholar