Synthesis of Carbon Nanomaterials-CdSe Composites and Their Photocatalytic Activity for Degradation of Methylene Blue

Chen, Ming-Liang; Meng, Ze-Da; Zhu, Lei; Park, Chong-Yeon; Choi, Jong-Geun; Ghosh, Trisha; Cho, Kwang-Youn; Oh, Won-Chun

doi:https://doi.org/10.1155/2012/964872

Journal of Nanomaterials

On this page

Abstract Introduction Experimental Results Conclusions References Copyright Related Articles

Research Article | Open Access

Volume 2012 | Article ID 964872 | https://doi.org/10.1155/2012/964872

Synthesis of Carbon Nanomaterials-CdSe Composites and Their Photocatalytic Activity for Degradation of Methylene Blue

Ming-Liang Chen,^1,2Ze-Da Meng,¹Lei Zhu,¹Chong-Yeon Park,¹Jong-Geun Choi,¹Trisha Ghosh,¹Kwang-Youn Cho,³and Won-Chun Oh¹

Academic Editor: Chunyi Zhi

Received08 Oct 2011

Accepted07 Nov 2011

Published27 Feb 2012

Abstract

We use multi-walled carbon nanotube (MWCNT) and graphene as carbon nanomaterials to obtain carbon nanomaterilas-CdSe composites using a facile hydrothermal method. The intrinsic characteristics of resulting composites were studied by X-ray diffraction (XRD), Scanning electron microscopy (SEM) with energy dispersive X-ray (EDX) analysis, transmission electron microscopy (TEM) and UV-vis diffuse reflectance spectrophotometer. The as-prepared carbon nanomaterilas-CdSe composites possessed great adsorptivity of dyes, extended light absorption range, and efficient charge separation properties simultaneously. Hence, in the photodegradation of methylene blue, a significant enhancement in the reaction rate was observed with carbon nanomaterilas-CdSe composites, compared to the CdSe compound.

1. Introduction

Carbon nanotube (CNT) was discovered in 1991 by Iijima [1] it has received considerable attention from many researchers [2–4] due to its interesting properties and wide applications. In addition to its outstanding mechanical characteristics, CNT exhibits excellent electrical, mechanical, magnetic, and thermal properties. These superior properties provide exciting opportunities to produce advanced materials for new applications [5–8]. A common use of CNT is to disperse it in other media as a reinforcement to enhance and modify their original characteristics. Graphene is considered a 2-dimensional carbon with a one-atom-thick planar sheet of sp² bonded carbon atoms that are densely packed in a honeycomb crystal lattice. Graphene is predicted to have remarkable properties, such as high thermal conductivity, superior mechanical properties, and excellent electronic transport properties [9–12]. These intrinsic properties of graphene have generated enormous interest for its possible implementation in a myriad of devices [13].

Recently, semiconductor nanoparticles such as TiO₂, ZnO, and CdSe quantum dot have been utilized to decorate CNT or graphene nanosheets to prepare carbon nanomaterials-based materials with remarkable optical and photovoltaic properties [14, 15]. Cadmium selenide (CdSe) is a kind of semiconductor with forbidden zone of 1.7 eV, and its valence electrons can be easily evoked to conduction band when the light wavelength of evoking light is less than or equal to 730 nm. In addition, CdSe is good photocatalyst because of the rapid generation of electron-hole pairs by photo-excitation and the highly negative reduction potentials of excited electrons [16, 17]. Functionalizing CNT and graphene nanosheets with CdSe not only can combine these advantages of CdSe and CNT and graphene nanosheets but also may result in new properties.

Hence, we used multiwalled carbon nanotube (MWCNT) and graphene as carbon nanomaterials for the synthesis of carbon-nanomaterials-CdSe composites. The intrinsic characteristics of resulting composites were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM) with energy dispersive X-ray (EDX) analysis, transmission electron microscopy (TEM), and UV-vis diffuse reflectance spectrophotometer. The photocatalytic activity of the as-synthesized samples was evaluated by degrading methylene blue (MB) under irradiation of visible light.

2. Experimental

2.1. Materials

Crystalline MWCNT powder (diameter: 20 nm, length: 5 μm) of 95.9 wt. % purity from Carbon Nano-material Technology Co., Ltd., Korea, was used as one of carbon nanomaterials. Graphene oxide which was prepared by a Hummers-Offeman method in our previous works [18–20] was used as another carbon nanomaterial. For the oxidization of MWCNT, m-chloroperbenzoic acid (MCPBA) chosen as the oxidizing agent was purchased from Acros Organics, New Jersey, USA. Benzene (99.5%) was used as the organic solvent which is purchased from the Samchun Pure Chemical Co., Ltd, Korea. Cadmium acetate dihydrate (Cd(CH₃COO)₂, 98%), selenium metal powder (Se), and ammonium hydroxide (NH₄OH, 28%) were purchased from Dae Jung Chemicals & Metal Co., Ltd, Korea. Anhydrous purified sodium sulfite (Na₂SO₃, 95%) was purchased from the Duksan Pharmaceutical Co., Ltd, Korea. The MB (C₁₆H₁₈N₃S·Cl, 99.99%) was used as model pollutant which is purchased from the Duksan Pure Chemical Co., Ltd, Korea. All chemicals were used without further purification, and all experiments were carried out using distilled water.

2.2. Synthesis of CdSe and Carbon-Nanomaterials-CdSe Composites

2.2.1. Synthesis of CdSe

For the synthesis of CdSe compound, the sodium selenosulfite (Na₂SeSO₃) solution and solution were prepared at first. Na₂SO₃ (5 g) and selenium metal powder (0.5 g) were dissolved in 30 mL distilled water and refluxed for 1 h to form Na₂SeSO₃ solution. Meanwhile, Cd(CH₃COO)₂ (0.5 g) was dissolved in 2 mL distilled water. NH₄OH (6 mL) was added to it, and the mixture was stirred till it dissolved completely to form solution. Finally, solution and Na₂SeSO₃ solution were mixed together, and the mixture was stirred and refluxed for at least 5 h. After the temperature of the mixture was brought down to room temperature and the mixture was filtered through the Whatman filter paper, the solid obtained was collected and washed with distilled water 5 times. After being dried in vacuum at 353 K for 8 h, the CdSe compound was obtained.

2.2.2. Synthesis of Carbon-Nanomaterials-CdSe Composite

MWCNT had to functionalize by MCPBA to introduce active function groups as it was very stable. 1 g MCPBA was melted in 60 mL benzene. And then 0.5 g MWCNT was put into the oxidizing agent. The mixture was stirred with a magnet for 6 h at 343 K. Then the MWCNT was dried at 373 K and spared.

The same amounts of graphene oxide and functionalized MWCNT were mixed with Cd solution and Na₂SeSO₃ solution which were prepared as above mentioned, and the mixtures were stirred and refluxed for at least 5 h, respectively. After the temperature of the mixtures was brought down to room temperature and the mixtures were filtered through What-man filter paper, the solids obtained were collected and washed with distilled water for 5 times. After being dried in vacuum at 353 K for 8 h, the graphene-CdSe composite and CNT-CdSe composite were obtained.

2.3. Characterization

X-ray diffraction (XRD, Shimadz XD-D1) result was used to identify the crystallinity with monochromatic high-intensity CuKα radiation (λ= 1.5406 Å). Scanning electron microscopy (SEM, JSM-5600) was used to observe the surface state and structure of prepared composite using an electron microscope. Transmission electron microscopy (TEM, Jeol, JEM- 2010, Japan) was used to determine the state and particle size of prepared composite. TEM at an acceleration voltage of 200 kV was used to investigate the number and the stacking state of graphene layers on various samples. TEM specimens were prepared by placing a few drops of sample solution on a carbon grid. The element mapping over the desired region of prepared composite was detected by an energy dispersive X-ray (EDX) analysis attached to SEM. UV-vis diffuse reflectance spectra (DRS) were obtained using an UV-vis spectrophotometer (Neosys-2000) by using BaSO₄ as a reference at room temperature and were converted from reflection to absorbance by the Kubelka-Munk method.

2.4. Photocatalytic Activity Measurements

The photocatalytic activity under visible light (KLD-08L, 220 V, 50–60 Hz, 8W, pure white, nm, Fawoo Tech) irradiation of the carbon-nanomaterials-CdSe composites was evaluated by using MB as the model substrate. In an ordinary photocatalytic test performed at room temperature, 0.05 g graphene-CdSe composite and CNT-CdSe composite were added to 50 mL of 5.0 × 10^-5mol/L MB solution, respectively. Before turning on the visible lamp, the solution mixed with composite was kept in the dark for at least 2 h, allowing the adsorption/desorption equilibrium to be reached. Then, the solutions were irradiated with visible lamp. The first sample was taken out at the end of the dark adsorption period (just before the light was turned on), in order to determine the MB concentration in solution after dark adsorption, which was hereafter considered as the initial concentration (c₀). Samples were then withdrawn regularly from the reactor by an order of 30 min, 60 min, 90 min, 120 min, 180 min, and 240 min, and immediately centrifuged to separate any suspended solid. The clean transparent solutions were analyzed by using a UV-vis spectrophotometer (Optizen POP) at wavelength of 665 nm [21].

3. Results and Discussions

3.1. Characterization

Figure 1 shows X-ray patterns of CdSe compound, graphene-CdSe composite, and CNT-CdSe composite. For CdSe compound, the XRD diffraction peaks around of 25.4°, 42°, and 49.6°, which can be indexed to the characteristic peaks (111), (220), and (311) plane reflections of cubic crystal structure CdSe with lattice constants of 6.05 Å according to the standard powder diffraction data (JCPDS No. 65–2891 for CdSe, cubic) [22, 23]. However, for graphene-CdSe composite and CNT-CdSe composite, only the typical peaks arosing from CdSe were detected. The (002) and (100) reflection around of 25.9° and 42.7° due to graphene overlaps the cubic (111) and (200) reflection around of 25.4° and 42° of CdSe. Therefore, the intensity of peaks at 25.4° and 42° in both of graphene-CdSe composite and CNT-CdSe composite is stronger than that in CdSe compound and the micromorphology of graphene-CdSe composite and CNT-CdSe composite is different from that of the mixture of Graphene or MWCNT and CdSe.

Figure 2 shows the SEM microphotographs of CdSe compound, graphene-CdSe composite, and CNT-CdSe composite. From Figures 2(a) and 2(b), very uniform spherical-shaped CdSe particles with agglomerate can together be observed. For graphene-CdSe composite (Figures 2(c) and 2(d)), spherical-shaped agglomerated CdSe particles are coated on the surface of graphene. For CNT-CdSe composite, as shown in Figures 2(e) and 2(f), spherical-shaped agglomerated CdSe particles are mixed with MWCNT. More detailed information of the surface state can be confirmed by the TEM. Figure 3 shows the TEM image of graphene-CdSe composite and CNT-CdSe composite, from which it can be clearly observed that the CdSe particles are homogenously coated on the surface of 2D structure grapheme for graphene-CdSe composite. For CNT-CdSe composite, the surface of MWCNTs has been coated with CdSe layers uniformly with particle size of about 10 nm.

(a)

(b)

(c)

(d)

(e)

(f)

(a)

(b)

To get information about change in elements and element weight%, the prepared CdSe compound, graphene-CdSe composite, and CNT-CdSe composite were examined by EDX. The weight % of main elements in CdSe compound, graphene-CdSe composite, and CNT-CdSe composite is shown in Table 1. Main elements, Cd and Se, were detected in all of CdSe compound, graphene-CdSe composite, and CNT-CdSe composite. Beside these two kinds of elements, Cd and Se, main element carbon was also exited in graphene-CdSe composite and CNT-CdSe composite. Some impurities such as Na, S, and O were also found in composites. The EDX results reveal the presence of CdSe and carbon with high content in prepared samples.

Figure 4 shows the UV-vis diffuse reflectance spectra of CdSe compound, graphene-CdSe composite, and CNT-CdSe composite at wavelength from 400 nm to 1100 nm. The reflectance characteristics of the CdSe compound were quite similar to those of the graphene-CdSe composite and CNT-CdSe composite except that the CdSe compound has an absorption edge at 830 nm. Substituting the critical wavelength of into the Planck equation , the band gap energy of CdSe is 1.74 eV, which is fairly close to literature value of 1.65 to 1.8 eV (CdSe) [16, 17]. Moreover, the prepared samples exhibit strong absorption in the visible light region with wavelength at 400–800 nm, assigned to the band adsorption of CdSe. And the absorption of graphene-CdSe composite and CNT-CdSe composite is higher than that of CdSe compound in visible light region, indicating the graphene-CdSe composite and CNT-CdSe composite would exhibit more excellent photoactivity than CdSe compound.

3.2. Photodegradation of MB Solution

The photocatalytic activities of the prepared samples were evaluated by the photodegradation of MB aqueous solution under visible light irradiation. The decreasing concentration of MB in the photocatalytic reaction was used to evaluate the activity of the composite. Figure 5 represents the degradation of MB over CdSe compound, graphene-CdSe composite, and CNT-CdSe composite under visible light irradiation, from which we can clearly see that the concentration of the MB solution gradually diminishes with increasing irradiation time for all of samples. After irradiation for 240 min, the CdSe compound has almost no photocatalytic activity toward the photodegradation of MB solution. The presumed reason is that a mass of visible light may be absorbed by the MB molecules in aqueous solution rather than the CdSe particles for high MB concentration, which can reduce the efficiency of the catalytic reaction. However, for graphene-CdSe composite and CNT-CdSe composite, a much excellent photocatalytic activity toward the photodegradation of MB solution can be observed and the MB concentration is removed 55% after irradiation under visible light for 240 min. The high activity can be attributed to the synergetic effects of high electron absorptivity and high charge mobility of carbon nanomaterials.

The scheme of excitation and charge transfer process between CdSe particles and graphene nanosheets or CNT under light irradiation is shown in Figure 6. Under irradiation by visible lamp, the graphene nanosheets and CNT acting as good electron acceptors [14, 24–26] can accept the electrons by light irradiation. Meanwhile, the CdSe can be also excited to produce the electrons and holes in the conduction band (CB) and valence band (VB) of CdSe. Then the electrons accepted by graphene nanosheets and CNT from light can transfer into the CB of CdSe, thereby increasing the number of electrons as well as the rate of electron-induced redox reactions. The generated electrons (e^–) probably react with dissolved oxygen molecules and produce oxygen peroxide radical , and the positively charged hole (h⁺) may react with the derived from H₂O to form hydroxyl radical . The MB molecule then can be photocatalytically degraded by oxygen peroxide radical and hydroxyl radical to CO₂, H₂O, and other mineralization.

4. Conclusions

High-purity carbon nanomaterials-CdSe composites were prepared by a simple hydrothermal method. Typical cubic CdSe structure can be observed in XRD patterns of all of carbon nanomaterials-CdSe composites. From the SEM and TEM results, for graphene-CdSe composite, spherical-shaped agglomerated CdSe particles are homogenously coated on the surface of 2D structure grapheme for graphene-CdSe composite. For CNT-CdSe composite, the surface of MWCNTs has been coated with CdSe layers uniformly with particle size of about 10 nm. The carbon nanomaterials-CdSe composites show a higher absorption under visible light region compared with CdSe compound. The MB degradation results suggest the carbon-nanomaterials-CdSe composites are much more effective photocatalyst than CdSe compound. The high activity can be attributed to the synergetic effects of high electron absorptivity and high charge mobility of carbon nanomaterials.

References

S. Iijima, “Helical microtubules of graphitic carbon,” Nature, vol. 354, no. 6348, pp. 56–58, 1991.
View at: Google Scholar
M. Hughes, G. Z. Chen, M. S. P. Shaffer, D. J. Fray, and A. H. Windle, “Electrochemical capacitance of a nanoporous composite of carbon nanotubes and polypyrrole,” Chemistry of Materials, vol. 14, no. 4, pp. 1610–1613, 2002.
View at: Publisher Site | Google Scholar
D. N. Futaba, J. Goto, S. Yasuda, T. Yamada, M. Yumura, and K. Hata, “A background level of oxygen-containing aromatics for synthetic control of carbon nanotube structure,” Journal of the American Chemical Society, vol. 131, no. 44, pp. 15992–15993, 2009.
View at: Publisher Site | Google Scholar
S. J. Pastine, D. Okawa, B. Kessler et al., “A facile and patternable method for the surface modification of carbon nanotube forests using perfluoroarylazides,” Journal of the American Chemical Society, vol. 130, no. 13, pp. 4238–4239, 2008.
View at: Publisher Site | Google Scholar
R. Hu, B. A. Cola, N. Haram et al., “Harvesting waste thermal energy using a carbon-nanotube-based thermo-electrochemical cell,” Nano letters, vol. 10, no. 3, pp. 838–846, 2010.
View at: Publisher Site | Google Scholar
M. S. Arnold, J. D. Zimmerman, C. K. Renshaw et al., “Broad spectral response using carbon nanotube/organic semiconductor/C 60 photodetectors,” Nano Letters, vol. 9, no. 9, pp. 3354–3358, 2009.
View at: Publisher Site | Google Scholar
K. P. Yung, J. Wei, and B. K. Tay, “Formation and assembly of carbon nanotube bumps for interconnection applications,” Diamond and Related Materials, vol. 18, no. 9, pp. 1109–1113, 2009.
View at: Publisher Site | Google Scholar
Y. C. Tsai, J. D. Huang, and C. C. Chiu, “Amperometric ethanol biosensor based on poly(vinyl alcohol)-multiwalled carbon nanotube-alcohol dehydrogenase biocomposite,” Biosensors and Bioelectronics, vol. 22, no. 12, pp. 3051–3056, 2007.
View at: Publisher Site | Google Scholar
D. R. Dreyer, S. Park, C. W. Bielawski, and R. S. Ruoff, “The chemistry of graphene oxide,” Chemical Society reviews, vol. 39, no. 1, pp. 228–240, 2010.
View at: Google Scholar
G. Wang, X. Shen, B. Wang, J. Yao, and J. Park, “Synthesis and characterisation of hydrophilic and organophilic graphene nanosheets,” Carbon, vol. 47, no. 5, pp. 1359–1364, 2009.
View at: Publisher Site | Google Scholar
X. Li, X. Wang, L. Zhang, S. Lee, and H. Dai, “Chemically derived, ultrasmooth graphene nanoribbon semiconductors,” Science, vol. 319, no. 5867, pp. 1229–1232, 2008.
View at: Publisher Site | Google Scholar
P. Blake, P. D. Brimicombe, R. R. Nair et al., “Graphene-based liquid crystal device,” Nano Letters, vol. 8, no. 6, pp. 1704–1708, 2008.
View at: Publisher Site | Google Scholar
M. J. Allen, V. C. Tung, and R. B. Kaner, “Honeycomb carbon: a review of graphene,” Chemical Reviews, vol. 110, no. 1, pp. 132–145, 2010.
View at: Publisher Site | Google Scholar
G. Williams, B. Seger, and P. V. Kamt, “TiO2-graphene nanocomposites. UV-assisted photocatalytic reduction of graphene oxide,” ACS Nano, vol. 2, no. 7, pp. 1487–1491, 2008.
View at: Publisher Site | Google Scholar
C. Nethravathi, T. Nisha, N. Ravishankar, C. Shivakumara, and M. Rajamathi, “Graphene-nanocrystalline metal sulphide composites produced by a one-pot reaction starting from graphite oxide,” Carbon, vol. 47, no. 8, pp. 2054–2059, 2009.
View at: Publisher Site | Google Scholar
I. Robel, V. Subramanian, M. Kuno, and P. V. Kamat, “Quantum dot solar cells. Harvesting light energy with CdSe nanocrystals molecularly linked to mesoscopic TiO₂ films,” Journal of the American Chemical Society, vol. 128, no. 7, pp. 2385–2393, 2006.
View at: Publisher Site | Google Scholar
R. Plass, S. Pelet, J. Krueger, M. Grätzel, and U. Bach, “Quantum dot sensitization of organic-inorganic hybrid solar cells,” Journal of Physical Chemistry B, vol. 106, no. 31, pp. 7578–7580, 2002.
View at: Publisher Site | Google Scholar
W. C. Oh, M. L. Chen, K. Zhang, F. J. Zhang, and W. K. Jang, “The effect of thermal and ultrasonic treatment on the formation of graphene-oxide nanosheets,” Journal of the Korean Physical Society, vol. 56, no. 4, pp. 1097–1102, 2010.
View at: Publisher Site | Google Scholar
W. C. Oh and F. J. Zhang, “Preparation and characterization of graphene oxide reduced from a mild chemical method,” Asian Journal of Chemistry, vol. 23, no. 2, pp. 875–879, 2011.
View at: Google Scholar
M. L. Chen, C. Y. Park, J. G. Choi, and W. C. Oh, “Synthesis of characterization of metal (Pt, Pd and Fe)-graphene composites,” Journal of the Korean Ceramic Society, vol. 48, p. 147, 2011.
View at: Google Scholar
M. L. Chen, F. J. Zhang, K. Zhang, Z. D. Meng, and W. C. Oh, “Photocatalytic degradation of methylene blue by CNT/TiO₂ composites prepared from MWCNT and titanium isopropoxide in tetrahydrofuran,” Journal of Photocatalysis, vol. 1, p. 19, 2010.
View at: Google Scholar
T. Wang, J. Wang, Y. Zhu, F. Xue, J. Cao, and Y. Qian, “Solvothermal synthesis and characterization of CdSe nanocrystals with controllable phase and morphology,” Journal of Physics and Chemistry of Solids, vol. 71, no. 7, pp. 940–945, 2010.
View at: Publisher Site | Google Scholar
A. E. Raevskaya, A. L. Stroyuk, S. Y. Kuchmiy et al., “Growth and spectroscopic characterization of CdSe nanoparticles synthesized from CdCl₂ and Na₂SeSO₃ in aqueous gelatine solutions,” Colloids and Surfaces A, vol. 290, no. 1–3, pp. 304–309, 2006.
View at: Publisher Site | Google Scholar
I. V. Lightcap, T. H. Kosel, and P. V. Kamat, “Anchoring semiconductor and metal nanoparticles on a two-dimensional catalyst mat. storing and shuttling electrons with reduced graphene oxide,” Nano Letters, vol. 10, no. 2, pp. 577–583, 2010.
View at: Publisher Site | Google Scholar
M. L. Chen, F. J. Zhang, and W. C. Oh, “Synthesis, characterization, and photocatalytic analysis of CNT/TiO₂ composites derived from MWCNTs and titanium sources,” Xinxing Tan Cailiao/ New Carbon Materials, vol. 24, no. 2, pp. 159–166, 2009.
View at: Google Scholar
W. C. Oh, F. J. Zhang, and M. L. Chen, “Preparation of MWCNT/TiO₂ composites by using MWCNTs and Titanium(IV) alkoxide precursors in Benzene and their photocatalytic effect and bactericidal activity,” Bulletin of the Korean Chemical Society, vol. 30, no. 11, pp. 2637–2642, 2009.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2012 Ming-Liang Chen et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

2131

Downloads

2010

Citations