One-Step Synthesis of High-Quality Water-Soluble CdSe Quantum Dots Capped by <i>N</i>-Acetyl-L-cysteine <i>via</i> Hydrothermal Method and Their Characterization

Wei, Chunjin; Li, Jinyu; Gao, Fang; Guo, Shuxia; Zhou, Yongcui; Zhao, Dan

doi:https://doi.org/10.1155/2015/369145

Journal of Spectroscopy

On this page

Abstract Introduction Results and Discussion Conclusion Acknowledgments References Copyright Related Articles

Special Issue

Spectroscopy in Materials Chemistry

View this Special Issue

Research Article | Open Access

Volume 2015 | Article ID 369145 | https://doi.org/10.1155/2015/369145

One-Step Synthesis of High-Quality Water-Soluble CdSe Quantum Dots Capped by N-Acetyl-L-cysteine via Hydrothermal Method and Their Characterization

Chunjin Wei,¹Jinyu Li,¹Fang Gao,¹Shuxia Guo,¹Yongcui Zhou,¹and Dan Zhao¹

Academic Editor: Qingrui Zhang

Received11 Aug 2014

Revised24 Oct 2014

Accepted27 Oct 2014

Published03 Aug 2015

Abstract

Novel water-soluble CdSe quantum dots (QDs) have been prepared with N-acetyl-L-cysteine as new stabilizer through a one-step hydrothermal route. The influence of experimental conditions, including reaction time, molar ratio of reactants, and pH value, on the luminescent properties of the obtained CdSe QDs has been systematically investigated. The characterization of as-prepared QDs was carried out through different methods. In particular, we realized qualitative and semiquantitative studies on CdSe QDs through X-ray photoelectron spectroscopy and electron diffraction spectroscopy. The results show that the as-prepared CdSe QDs exhibit a high quantum yield (up to 26.7%), high stability, and monodispersity and might be widely used in biochemical detection and biochemical research.

1. Introduction

Quantum dots (QDs) are nanomaterials usually composed of II–VI or III–V elements [1]. The unique optical properties caused by their small diameters (1–10 nm) lead to their promising applications in biochemistry detections [2], biological labeling [3], cell imaging in vivo [4], solar battery [5], and electronic equipment [6].

Among QDs made up of II–VI group elements, CdSe QDs have attracted broad interests due to their fluorescence emission in visible light range [7]. Though selenium and telluride are both VI group elements, the spectra properties of the prepared CdSe QDs are much worse than those of CdTe QDs, because those CdSe QDs with sulphydryl compounds (such as thioglycolate and cysteine) as stabilizers possess low quantum yields (QYs) and wide emission full width at half maximum (FWHM) (>100 nm) [8]. Since synthesis method and the used stabilizer would greatly affect the optical properties of prepared QDs, the studies on the choice of stabilizer during the synthesis process of water-soluble QDs have been widely reported [8], including thiomalic acid, thioglycolate, N-(2-mercaptopropionyl)glycine, glutathione, and L-cysteine. The reports on N-acetyl-L-cysteine (NAC) as the stabilizer during the synthesis, however, have not been seen in literature. NAC is known as an antioxidant and impurity removal reagent and can be used to protect cells from oxidation and QDs induced cytotoxicity [9, 10]. Additionally, it possesses good water-solubility, is nonvolatile and inodorous, have excellent biocompatibility, and is friendly to the environment and its users. The commonly employed methods for direct synthesis of QDs in aqueous solution are reflux method [11–13] and microwave radiation method [14–16]. These methods, however, have obvious weaknesses: the reflux method requires long reaction time and the prepared QDs have low QYs and wide FWHM, while the microwave radiation method requires complex synthesis equipment, which greatly limits their practical applications. The hydrothermal route [17] is a newly developed hydrothermal route for direct synthesis of water-soluble QDs in an airtight reaction vessel (autoclave) under high pressure and temperature. The high temperature (usually supercritical temperature or close to critical temperature) speeds up the growth of QDs, decreases the surface defects, and thus reduces the probability of fluorescence quenching induced by irradiative decay and improves the fluorescence efficiency of prepared QDs [9]. Compared with core/shell CdSe/CdS QDs prepared by two-step method, the hydrothermal method allows rapid synthesis of QDs through one-step process with stabilizer simultaneously as the sulfur source. The simple synthesis process is thus an ideal method to improve the optical property of prepared QDs.

In this paper, we report the synthesis of high-quality water-soluble CdSe QDs through one-step hydrothermal method and discuss the impacts of important experiment parameters (reaction time, pH, feed ratio, etc.) on the optical properties of prepared QDs. The synthesized CdSe QDs have been characterized through fluorescence spectroscopy, UV absorption spectroscopy, high resolution transmission electron microscopy (HRTEM), X-ray powder diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and electron diffraction spectroscopy (EDS), and their morphology, crystal structure, optical properties, and element composition have been studied with these means. The prepared CdSe QDs meet the requirements for the fluorescence materials in biological labeling and will surely have promising applications in biochemical detection and biomedical researches.

2. Experimental Procedures

2.1. Chemicals

Selenium (reagent powder) was purchased from Shanghai Mei Xing Chemical Co., Ltd. CdCl₂, rhodamine 6G, and sodium borohydride (NaBH₄) were obtained from Sinopharm Chemical Reagent. NAC was purchased from Sigma. All chemicals used were of analytical grade or of the highest purity available. All solutions were prepared using Milli-Q water (Millipore) as the solvent.

2.2. Preparation of CdSe QDs

Sodium borohydride (0.0250 g) and selenium powder (0.0100 g) were dissolved in 3 mL ultrapure water in a 5 mL one-necked flask to produce sodium hydroselenide (NaHSe, 0.0422 mol/L). A small outlet connected to the flask was kept open to discharge the pressure from the resulting hydrogen. After approximately 30 min, the black selenium powder disappeared, and the small outlet was then completely shut. Fresh NaHSe solution was then kept in freezer for further use.

CdCl₂ (6.4 mmol/L) and a certain amount of NAC were dissolved in 50 mL of deionized water and stirred vigorously for 20 minutes. The precursor solution was adjusted to desired value (8.5 to 11) by stepwise addition of 1.0 mol/L of NaOH. Subsequently, the fresh NaHSe solution (0.0422 mol/L) was added to a N₂-saturated mixture of CdCl₂ and NAC with a certain percentage and stirred vigorously for 5 minutes. The Cd²⁺ concentration was 6.4 mmol/L in a total volume of 50 mL. The molar ratios of NAC/Cd²⁺ used in our experiment are 1.2 : 1, 2.0 : 1, 2.4 : 1, 3.0 : 1, and 3.6 : 1, in sequence. The molar ratios of Se²⁺/Cd²⁺ used in our experiment are 0.025 : 1, 0.05 : 1, 0.10 : 1, 0.15 : 1, and 0.20 : 1, in sequence. Finally, the resulting mixture was put into a 50 mL Teflon-lined stainless steel autoclave. It was loaded in an oven at 200°C for a specified time (50 to 70 min) and then cooled to the room temperature by a hydrocooling process.

To remove NAC-Cd complexes at the end of the synthesis, cold 2-propanol was added to the reaction mixture to precipitate NAC-capped CdSe QDs. The as-prepared products were dried overnight under vacuum at 40°C for further experiments.

2.3. Characterization

UV-visible absorption spectra were acquired with a Lambda-35 UV/visible spectrophotometer (PerkinElmer Company) to determine the absorption of QDs. Fluorescence spectra were recorded on a LS55 spectrofluorometer (PerkinElmer Company). All optical measurements were performed at room temperature under ambient conditions. The HRTEM sample was prepared by dropping an aqueous CdSe QDs solution onto an Agar carbon-coated copper grid (400 meshes) with the excess solvent evaporated. The HRTEM image was obtained via JEM-2100 (HR) transmission electron microscope (Japan Electron Optics Laboratory CO., Ltd.). XRD spectrum was recorded on a Shimadzu XRD-2000 X-ray diffractometer. EDS spectrum was captured with an FEI Quanta 200 scanning electron microscope equipped with an energy dispersive X-ray spectrometer. XPS measurements were acquired with a Leybold Heraeus SKL 12 X-ray photoelectron spectrometer. The QY of CdSe QDs was measured according to the literature [18]. Rhodamine 6G in ethanol was chosen as the reference standard (QY = 95%).

3. Results and Discussion

3.1. Influence of Reaction Time

Since the optical properties of the prepared CdSe QDs are greatly influenced by a series of experimental parameters, such as reaction time, feeding ratio of the reaction reagents, and the pH value, the optimizing experiments were carried out in order to acquire the high-quality QDs.

The reaction temperature is a very important factor that influences optical properties of the prepared QDs. The low temperature (<170°C) would decrease the reaction rate, prolong the reaction time, and consequently lead to the low QYs of the prepared QDs. The high reaction temperature, on the other hand, will produce white precipitates in the autoclave together with pungent odor, which may be the result of the decomposition of NAC under such high temperature, losing its ability as stabilizer. Therefore, the optimum reaction time is in the range of 170 to 210°C.

With other reaction parameters fixed ([Cd] = 6.4 mmol/L, (Cd) : (Se) : (NAC) = 1.0 : 0.05 : 3.0, pH = 9, and reaction temperature at 200°C), experiments were carried out to examine the impact of reaction time (50–70 min) upon the quality of prepared CdSe QDs. As shown in Figure 1, different from the obvious redshifts of the emission peak of NAC-capped CdTe QDs with the prolonged reaction time [17], the emission peaks of CdSe QDs show no obvious shift (540–555 nm) with the increase of reaction time, and their FWHM of fluorescence spectra (26–31 nm) as well as absorption peaks of UV spectra (516–532 nm) also generally stay stable. The QYs of the prepared QDs, however, are greatly influenced by the reaction time. The CdSe QDs prepared at 65 min possess the highest QY. The mechanism of this phenomenon is that at the initial stage of the reaction, NAC combines with the surface of CdSe QDs as the ligand, while with the reaction continuing, NAC decomposes under high temperature, releases S^2- into the solution, and forms CdS with the Cd ions on the surface of CdSe QDs. The formed CdS through alloying reaction can decrease the surface defects of the QDs and thus improves their QYs. When the reaction time is over 65 min, the overdecomposition of NAC would deprive its ability as stabilizer and thus fails to synthesize water-soluble QDs [9].

3.2. Influence of Molar Ratio of Se to Cd

The molar ratio of Se to Cd during the synthesis would greatly influence the element composition of the prepared QDs and thus impact the QYs of the prepared CdSe QDs. With other experiment parameters fixed ([Cd] = 6.4 mmol/L, (Cd) : (NAC) = 1.0 : 3.0, pH = 9, reaction temperature at 200°C, and reaction time at 65 min), the molar ratios of Se to Cd were gradually increased from 0.025 to 0.20. As shown in Figure 2, the change of molar ratio of Se to Cd does not produce obvious influence upon the emission peak of prepared CdSe QDs, with their emission peak mainly at approximately 554 nm, but it shows great impact on the QYs of prepared QDs. The QYs of QDs reach the maximum when (Se)/(Cd) is at 0.05. The high molar ratio of Se to Cd would increase Se content in the prepared CdSe QDs, and the easy oxidation of Se on the surface of QDs would produce many nonradioactive combination sites, leading to the degradation of QY.

3.3. Influence of pH of Precursor Solution

Since QDs are prone to aggregate under acid environment, the impacts of alkaline condition (pH = 8.5–11) of the precursor solution on the prepared CdSe QDs were the focus of our research. As shown in Figure 3, with other synthesis parameters fixed ([Cd] = 6.4 mmol/L, (Cd) : (Se) : (NAC) = 1.0 : 0.05 : 3.0, reaction time at 65 min, and reaction temperature at 200°C), the result shows that the pH also sets no obvious impact on the emission peak of fluorescence spectra (555 nm) and absorption peak of UV spectra (533 nm) when pH value is in the range of 8.5 to 9.5. However, when pH reaches the range of 9.5 to 11.0, the emission peak red-shifts to 589 nm and the UV absorption peak red-shifts to 566 nm, showing that the alkaline environment is beneficial to the reaction speed of the synthesis and further increases the particle diameter of the prepared QDs. The QY reaches the maximum when the pH is at 9.0.

(a)

(b)

3.4. Influence of Molar Ratio of NAC to Cd

With other experiment parameters fixed ([Cd] = 6.4 mmol/L, (Cd) : (Se) = 1 : 0.05, pH = 9, reaction time at 65 min, and reaction temperature at 200°C), the impacts of varied amount of the stabilizer NAC upon the prepared CdSe QDs have been studied. As shown in Figure 4, when the molar ratio of Cd to NAC reaches 1 : 3, the QY of prepared QDs is the highest, and the higher or lower molar ratio would both lead to decreased quantum yield. Since the effect of stabilizer is to inactivate the surface defects of QDs to decrease the nonradioactive recombination, the concentration of the stabilizer is of great significance for the optical properties of prepared QDs. The improper concentration of the stabilizer would greatly lead to debased fluorescence efficiency. The experiments showed that low molar ratio of NAC to Cd (1.2 : 1) led to weak fluorescence intensity, which may be the result of small amount of NAC capped on the surface of QDs caused by shortage of combination sites [8]. When the molar ratio of NAC to Cd rose to 3 : 1, the fluorescence intensity of prepared CdSe QDs is greatly improved with the emission peak red-shifting from 523 nm to 555 nm and the absorption peak red-shifting from 500 nm to 523 nm. This is because the high ratio of NAC would greatly lessen the surface defects on the surface of QDs [9, 10]. The S²⁻ ions released from the decomposition of NAC under high temperature dope with Cd and form CdS onto the surface of QDs, effectively inactivating the surface defects of QDs [9]. Moreover, the formation of CdS can increase the particle diameter of the QDs and decrease the band gap energy, leading to the red shift of the absorption peak. However, when the molar ratio is too high, the formation of more stable dithio complexes between NAC and Cd can lessen the concentration of free Cd ions, increase the molar ratio of Se in the prepared CdSe QDs, and lead to more surface defects and thus low QYs [17].

(a)

(b)

Through a series of optimal experiments, the optimum synthesis parameters for NAC-capped CdSe QDs have been acquired: [Cd] = 6.4 mmol/L, (Cd) : (Se) : (NAC) = 1 : 0.05 : 3.0, reaction temperature at 200°C, reaction time at 65 min, and . The QY of prepared CdSe QDs under such optimum condition is 26.7%. The properties of QDs have been examined via HRTEM, XRD, XPS, and EDS, and the mechanism of S ions doping on the surface of CdSe QDs has been further proven via these characterization methods.

3.5. Characterization via XRD and HRTEM

The morphology of the as-prepared NAC-capped CdSe QDs was studied by HRTEM. Figure 5 depicts the HRTEM image for as-prepared nanoparticles; the HRTEM image of single QD and electron diffraction pattern (SAED) are shown as insets, demonstrating the relatively narrow size distribution and spherical morphologies of the prepared QDs. The presence of lattice planes in the high resolution image confirms that the nanocrystals have better crystallinity which is further supported by the SAED pattern. In addition, it is noticed that the as-prepared nanoparticles possess good dispersivity. The HRTEM images of the prepared nanoparticles show the average particles sizes of 5.4 nm. The diameter of the prepared particles is in consistency with the already reported core/shell structure model for CdSe/CdS sample (5 nm) [19] and larger than that of the CdSe nanoparticles (3.5 nm) [20], which implies a core/shell structure.

The powder XRD patterns of NAC-capped CdSe QDs are shown in Figure 6. In the XRD pattern of prepared QDs, three characteristic diffraction peaks at , 43.56, and 50.38 degrees standing for the (111), (220), and (311) planes of cubic zinc blende CdSe/CdS could be recognized clearly. In comparison with the XRD pattern of the CdSe QDs [21], the three diffraction peaks only shifted slightly toward larger angles of the values for CdS [22], which demonstrated the formation of the CdS shell on the surface of the CdSe QD. This shows that NAC not only can combine onto the surface of QDs through the combination of its hydrosulfide group with Cd of QDs, but also can release S²⁻ under high temperature to form doped CdS on the surface of CdSe QDs [9, 10].

3.6. Characterization via XPS

XPS is a quantitative, surface analytical tool sensitive to the atomic composition of the outermost 100 Å of a sample surface. As shown in Figure 7, the Cd (3d) peak at a binding energy of 404.03 eV, Se (3d) at 53.2 eV, and S (3d) at 162.0 eV are the characteristic peaks of CdSe QDs, showing the existence of Cd, Se, and S elements.

(a)

(b)

(c)

(d)

3.7. Characterization via EDS

The EDS technique has been employed to probe a semiquantitative picture of the composition of the NAC-capped CdSe QDs. As shown in Figure 8, the atom percentages of Cd, Se, and S reach 45.98%, 3.96%, and 50.06%, respectively. The S element in QDs derives from the ligand NAC on the surface of QDs, and the high percentage of S is partly the result of the doped CdS on the surface of QDs, which also provides evidence for doping of S on QDs surface.

3.8. The Impact of pH of QDs Solution on Their Fluorescence Intensity

The pH value of the QDs solution would greatly influence its fluorescence intensity and thus its practical applications in biochemistry fields. As shown in Figure 9, the as-prepared QDs show excellent stability when the pH value of the solution is in the range of 4 to 9, better than MSA capped CdSe QDs [13]. The too low or too high pH value would lead to weakened fluorescence intensity. This is because the protonation of NAC under acid condition would cause the detachment of NAC from the surface of QDs, leading to the decrease of fluorescence intensity; when pH value of the solution surpasses 9, the fluorescence weakens because of the formation of the precipitant Cd(OH)₂ [13]. Since the prepared NAC-capped CdSe QDs possess good stability under common biochemical conditions, they will surely be suitable for the applications in the biochemical detections.

4. Conclusion

The high-quality NAC-capped CdSe QDs have been prepared via one-step hydrothermal method with NAC as the stabilizer. The optimum synthesis parameters have been found, and the prepared CdSe QDs have been characterized in morphology and crystal structure via HRTEM and XRD. It is found that the particle size of CdSe QDs is smaller than that of CdSe/CdS, and their crystal structure is not standard CdSe cubic crystal system but close to CdS cubic crystal system. The XPS image shows the existence of Cd, Se, and S elements, and S atomic percentage calculated by EDs is relatively high. All these evidences prove the doping of S on the surface of CdSe QDs. The prepared NAC-capped CdSe QDs are stable with good monodispersity and high QY, ensuring their promising application in biochemistry detections and biomedical researches.

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

Acknowledgments

This research was supported by the National Science Foundation of China (21105130) and Innovation Training Project for College Students (GXX14210).

References

F. H. Huang, C. Cheng, and C. Sun, “Synthesis and characterization of water-soluble citrate-capped CdSe quantum dots,” Chemical Research, vol. 24, p. 1, 2013.
View at: Google Scholar
Z. L. Xu, K. Y. Yi, Z. N. Ma, M. Wang, and X. F. Liu, “Synthesis of CdSe quantum dots and their applications for labeling of latent fingerprints,” Synthetic Materials Aging and Application, vol. 42, p. 15, 2013.
View at: Google Scholar
Q. Wang, F. Ye, T. Fang et al., “Bovine serum albumin-directed synthesis of biocompatible CdSe quantum dots and bacteria labeling,” Journal of Colloid and Interface Science, vol. 355, no. 1, pp. 9–14, 2011.
View at: Publisher Site | Google Scholar
A. C. A. Silva, S. L. V. D. Deus, M. J. B. Silva, and N. O. Dantas, “Highly stable luminescence of CdSe magic-sized quantum dots in HeLa cells,” Sensors and Actuators B: Chemical, vol. 191, pp. 108–114, 2014.
View at: Publisher Site | Google Scholar
X. D. Guo, B. B. Ma, L. D. Wang, R. Gao, H. P. Dong, and Y. Qiu, “Electron injection and photovoltaic properties in CdSe/ZnS quantum dot sensitized solar cells,” Acta Physico-Chimica Sinica, vol. 29, pp. 1240–1246, 2013.
View at: Google Scholar
L. Z. Du and Y. A. Lei, “Synthesis of high-quality Cl-doped CdSe nanobelts and their application in nanodevices,” Materials Letters, vol. 106, pp. 100–103, 2013.
View at: Publisher Site | Google Scholar
D.-W. Deng, J.-S. Yu, and Y. Pan, “Water-soluble CdSe and CdSe/CdS nanocrystals: a greener synthetic route,” Journal of Colloid and Interface Science, vol. 299, no. 1, pp. 225–232, 2006.
View at: Publisher Site | Google Scholar
K. Wang, H. Q. Pan, S. Y. Liu, X. M. Xu, and L. Y. Zhou, “Preparation and characterization of high quality CdSe quantum dots in aqueous solution,” Chemical Journal of Chinese Universities, vol. 33, no. 12, pp. 2604–2608, 2012.
View at: Publisher Site | Google Scholar
Z. K. Zhao, Z. K. He, and M. M. F. Chanand, “Synthesis and characterization of high-quality water-soluble near-infrared-emitting CdTe/CdS quantum dots capped by N-acetyl-L-cysteine via hydrothermal method,” The Journal of Physical Chemistry C, vol. 113, p. 1293, 2009.
View at: Publisher Site | Google Scholar
Q. Wang, X. Zhou, T. Fang, P. Liu, X. Li, and X. Min, “One-step growth of high-quality CdTe quantum dots via hydrothermal method and cytotoxicity evaluation,” Powder Technology, vol. 247, pp. 81–86, 2013.
View at: Publisher Site | Google Scholar
X. L. Rong, Q. Zhao, and G. H. Tao, “Aqueous synthesis of CdSe and CdSe/CdS quantum dots with controllable introduction of Se and S sources,” Chinese Chemical Letters, vol. 23, no. 8, pp. 961–964, 2012.
View at: Publisher Site | Google Scholar
Y. Li, L. Liu, X. Fang, J. Bao, M. Han, and Z. Dai, “Electrochemiluminescence biosensor based on CdSe quantum dots for the detection of thrombin,” Electrochimica Acta, vol. 65, pp. 1–6, 2012.
View at: Publisher Site | Google Scholar
S. T. Chen, X. L. Zhang, Q. H. Zhang et al., “CdSe quantum dots decorated by mercaptosuccinic acid as fluorescence probe for Cu²⁺,” Journal of Luminescence, vol. 131, no. 5, pp. 947–951, 2011.
View at: Publisher Site | Google Scholar
T. Xuan, X. Wang, G. Zhu, H. Li, L. Pan, and Z. Sun, “One-step microwave-assisted synthesis of water soluble CdSe quantum dots for white light-emitting diodes with excellent color rendering,” Journal of Alloys and Compounds, vol. 558, pp. 105–108, 2013.
View at: Publisher Site | Google Scholar
D. W. Ayele, H. M. Chen, W. N. Su et al., “Controlled synthesis of CdSe quantum dots by a microwave-enhanced process: a green approach for mass production,” Chemistry, vol. 17, no. 20, pp. 5737–5744, 2011.
View at: Publisher Site | Google Scholar
M. M. Moghaddam, M. Baghbanzadeh, A. Keilbach, and C. O. Kappe, “Microwave-assisted synthesis of CdSe quantum dots: Can the electromagnetic field influence the formation and quality of the resulting nanocrystals?” Nanoscale, vol. 4, no. 23, pp. 7435–7442, 2012.
View at: Publisher Site | Google Scholar
J. T. Li, T. M. Yang, W. H. Chan, M. M. F. Choi, and D. Zhao, “Synthesis of high-quality N-acetyl-L-cysteine-capped CdTe quantum dots by hydrothermal route and the characterization through MALDI-TOF mass spectrometry,” The Journal of Physical Chemistry C, vol. 117, p. 19175, 2013.
View at: Google Scholar
R. Xie, U. Kolb, J. Li, T. Basché, and A. Mews, “Synthesis and characterization of highly luminescent CdSe-core CdS/Zn_0.5Cd_0.5S/ZnS multishell nanocrystals,” Journal of the American Chemical Society, vol. 127, no. 20, pp. 7480–7488, 2005.
View at: Publisher Site | Google Scholar
A. R. B. Suganthi, A. G. Joshi, and P. Sagayaraj, “A novel two-phase thermal approach for synthesizing CdSe/CdS core/shell nanostructure,” Journal of Nanoparticle Research, vol. 14, no. 2, article 691, 2012.
View at: Publisher Site | Google Scholar
K. B. Subila, G. Kishore Kumar, S. M. Shivaprasad, and K. George Thomas, “Luminescence properties of CdSe quantum dots: Role of crystal structure and surface composition,” Journal of Physical Chemistry Letters, vol. 4, no. 16, pp. 2774–2779, 2013.
View at: Publisher Site | Google Scholar
R. M. Hodlur and M. K. Rabinal, “A new selenium precursor for the aqueous synthesis of luminescent CdSe quantum dots,” Chemical Engineering Journal, vol. 244, pp. 82–88, 2014.
View at: Publisher Site | Google Scholar
A. Samadi-maybodi, F. Abbasi, and R. Akhoondi, “Aqueous synthesis and characterization of CdS quantum dots capped with some amino acids and investigations of their photocatalytic activities,” Colloids and Surfaces A: Physicochemical and Engineering Aspects, vol. 447, pp. 111–119, 2014.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2015 Chunjin Wei et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

3683

Downloads

1497

Citations