Table of Contents Author Guidelines Submit a Manuscript
Mathematical Problems in Engineering
Volume 2013, Article ID 875929, 5 pages
http://dx.doi.org/10.1155/2013/875929
Research Article

Noise Source Identification of a Ring-Plate Cycloid Reducer Based on Coherence Analysis

1School of Mechanical Engineering, Dalian Jiaotong University, Dalian 116028, China
2School of Traffic and Transportation Engineering, Dalian Jiaotong University, Dalian 116028, China

Received 16 November 2012; Revised 8 March 2013; Accepted 8 March 2013

Academic Editor: Valentina E. Balas

Copyright © 2013 Bing Yang and Yan Liu. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. W. D. He, X. Li, and L. Li, “Study on double crank ringplate-type cycloid drive,” Journal of Mechanical Engineering, vol. 36, no. 5, pp. 84–88, 2000. View at Google Scholar · View at Scopus
  2. W. D. He, X. Li, L. Li, and B. Wen, “Optimum design and experiment for reducing vibration and noise of double crank ring-plate-type pin-cycloid planetary drive,” Jixie Gongcheng Xuebao/Journal of Mechanical Engineering, vol. 46, no. 23, pp. 53–60, 2010. View at Publisher · View at Google Scholar · View at Scopus
  3. W. D. He, Q. Lu et al., “Study on pin cycloid planetary gear reducer used in propeller pitch variator for 1.5 MW wind turbine,” Journal of Mechanical Transmission, vol. 36, no. 7, pp. 1–4, 2012. View at Google Scholar
  4. X. Li, W. D. He, L. Li, and L. C. Schmidt, “A new cycloid drive with high-load capacity and high efficiency,” ASME Journal of Mechanical Design, vol. 126, no. 4, pp. 683–686, 2004. View at Publisher · View at Google Scholar · View at Scopus
  5. N. B. Roozen, J. Van den Oetelaar, A. Geerlings, and T. Vliegenthart, “Source identification and noise reduction of a reciprocating compressor; A case history,” International Journal of Acoustics and Vibrations, vol. 14, no. 2, pp. 90–98, 2009. View at Google Scholar · View at Scopus
  6. F. Payri, A. Broatch, X. Margot, and L. Monelletta, “Sound quality assessment of Diesel combustion noise using in-cylinder pressure components,” Measurement Science and Technology, vol. 20, no. 1, Article ID 015107, 2009. View at Publisher · View at Google Scholar · View at Scopus
  7. P. Simon, “Retrieving the three-dimensional matter power spectrum and galaxy biasing parameters from lensing tomography,” Astronomy and Astrophysics, vol. 543, no. 1, p. 1, 2012. View at Google Scholar
  8. C. C. Zhu, D. T. Qin, and S. Hong, “Study on surface noise distribution of three-ring reducer,” Journal of Chongqing University, vol. 4, pp. 18–21, 2000. View at Google Scholar
  9. T. J. Lin, Y. J. Liao, R. F. Li, and W. Liu, “Numerical simulation and experimental study on radiation noise of double-ring gear reducer,” Journal of Vibration and Shock, vol. 29, no. 3, pp. 43–47, 2010. View at Google Scholar · View at Scopus
  10. J. Prezelj and M. Čudina, “Quantification of aerodynamically induced noise and vibration-induced noise in a suction unit,” Proceedings of the Institution of Mechanical Engineers C, vol. 225, no. 3, pp. 617–624, 2011. View at Publisher · View at Google Scholar · View at Scopus
  11. Z. Chu, W. Wang, and X. Xiao, “Noise source identification and noise abatement of truck under idle speed condition,” Transactions of the Chinese Society of Agricultural Engineering, vol. 26, no. 5, pp. 153–158, 2010. View at Publisher · View at Google Scholar · View at Scopus
  12. A. Ramachandran, M. C. Reddy, and R. Moodithaya, “Minimization and identification of conducted emission bearing current in variable speed induction motor drives using PWM inverter,” Indian Academy of Sciences, vol. 33, no. 5, pp. 615–628, 2008. View at Publisher · View at Google Scholar · View at Scopus
  13. R. S. Magalhães, C. H. O. Fontes, L. A. L. Almeida, and M. Embiruçu, “Identification of hybrid ARXneural network models for three-dimensional simulation of a vibroacoustic system,” Journal of Sound and Vibration, vol. 330, no. 21, pp. 5138–5150, 2011. View at Publisher · View at Google Scholar · View at Scopus
  14. X. D. Wu, S. G. Zuo, and Y. Lu, “Identifying noise source based on application to partial coherence analysis in fuel cell car,” Journal of Noise and Vibration, vol. 3, pp. 81–84, 2008. View at Google Scholar
  15. M. L. Chen and S. M. Li, “Coherence functions method for signal source identification,” China Mechanical Engineering, vol. 1, pp. 95–100, 2007. View at Google Scholar
  16. K. S. Oh, S. K. Lee, and S. J. Kim, “Identification and reduction of noise from axles in a passenger vehicle,” Noise Control Engineering Journal, vol. 56, no. 5, pp. 332–341, 2008. View at Publisher · View at Google Scholar · View at Scopus
  17. F. Deželak, “Effective noise control through identification and ranking of incoherent noise sources,” Noise Control Engineering Journal, vol. 58, no. 2, pp. 212–221, 2010. View at Publisher · View at Google Scholar · View at Scopus
  18. H. E. Camargo, P. A. Ravetta, R. A. Burdisso, and A. K. Smith, “Application of phased array technology for identification of low frequency noise sources,” Journal of Low Frequency Noise Vibration and Active Control, vol. 28, no. 4, pp. 237–244, 2009. View at Publisher · View at Google Scholar · View at Scopus