Table of Contents Author Guidelines Submit a Manuscript
Mathematical Problems in Engineering
Volume 2015, Article ID 982785, 12 pages
http://dx.doi.org/10.1155/2015/982785
Research Article

Thermomechanical-Phase Transformation Simulation of High-Strength Steel in Hot Stamping

State Key Laboratory of Structural Analysis for Industrial Equipment, Faculty of Vehicle and Mechanics, Dalian University of Technology, Dalian 116024, China

Received 18 September 2014; Accepted 1 December 2014

Academic Editor: Chenfeng Li

Copyright © 2015 Wenhua Wu et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. N. Ma, P. Hu, and W. Guo, “Technology and equipment of hot forming for ultra high strength steel,” Automobile & Parts, no. 45, pp. 28–30, 2009. View at Google Scholar
  2. A. Makinouchi, “Sheet metal forming simulation in industry,” Journal of Materials Processing Technology, vol. 60, no. 1–4, pp. 19–26, 1996. View at Publisher · View at Google Scholar · View at Scopus
  3. P. Hu, “Rate-dependent quasi-flow corner theory for elastic/visco-plastic materials,” International Journal of Solids and Structures, vol. 41, no. 5-6, pp. 1263–1284, 2004. View at Publisher · View at Google Scholar · View at Scopus
  4. Y. Lin, D. Wen, J. Deng, G. Liu, and J. Chen, “Constitutive models for high-temperature flow behaviors of a Ni-based superalloy,” Materials & Design, vol. 59, pp. 115–123, 2014. View at Publisher · View at Google Scholar
  5. Z.-X. Gui, W.-K. Liang, Y. Liu, and Y.-S. Zhang, “Thermo-mechanical behavior of the Al-Si alloy coated hot stamping boron steel,” Materials and Design, vol. 60, pp. 26–33, 2014. View at Publisher · View at Google Scholar · View at Scopus
  6. E. J. F. R. Caron, K. J. Daun, and M. A. Wells, “Experimental heat transfer coefficient measurements during hot forming die quenching of boron steel at high temperatures,” International Journal of Heat and Mass Transfer, vol. 71, pp. 396–404, 2014. View at Publisher · View at Google Scholar · View at Scopus
  7. M. Raugei, O. El Fakir, L. Wang, J. Lin, and D. Morrey, “Life cycle assessment of the potential environmental benefits of a novel hot forming process in automotive manufacturing,” Journal of Cleaner Production, vol. 83, pp. 80–86, 2014. View at Publisher · View at Google Scholar
  8. G. Bergman and M. Oldenburg, “A finite element model for thermomechanical analysis of sheet metal forming,” International Journal for Numerical Methods in Engineering, vol. 59, no. 9, pp. 1167–1186, 2004. View at Publisher · View at Google Scholar · View at Scopus
  9. M. Eriksson, M. Oldenburg, M. C. Somani, and L. P. Karjalainen, “Testing and evaluation of material data for analysis of forming and hardening of boron steel components,” Modelling and Simulation in Materials Science and Engineering, vol. 10, no. 3, pp. 277–294, 2002. View at Publisher · View at Google Scholar · View at Scopus
  10. M. Naderi, V. Uthaisangsuk, U. Prahl, and W. Bleck, “A numerical and experimental investigation into hot stamping of boron alloyed heat treated steels,” Steel Research International, vol. 79, no. 2, pp. 77–84, 2008. View at Publisher · View at Google Scholar · View at Scopus
  11. M. Merklein and J. Lechler, “Investigation of the thermo-mechanical properties of hot stamping steels,” Journal of Materials Processing Technology, vol. 177, no. 1–3, pp. 452–455, 2006. View at Publisher · View at Google Scholar · View at Scopus
  12. Y. Chang, X. H. Tang, K. M. Zhao, P. Hu, and Y. C. Wu, “Investigation of the factors influencing the interfacial heat transfer coefficient in hot stamping,” Journal of Materials Processing Technology, 2014. View at Publisher · View at Google Scholar
  13. N. Ma, P. Hu, W. Guo et al., “Feasible methods applied to the design and manufacturing process of hot forming,” in Proceedings of the International Deep Drawing Research Group Conference (IDDRG '09), pp. 835–843, Golden, Colo, USA, 2009.
  14. N. Ma, W.-H. Wu, G.-Z. Shen, and P. Hu, “Study of hot forming for high strength steel: numerical simulation-static explicit algorithm,” Chinese Journal of Computational Mechanics, vol. 28, no. 3, pp. 371–376, 2011. View at Google Scholar · View at Scopus
  15. D.-X. Jiang, W.-H. Wu, and P. Hu, “Research on temperature numerical simulation of hot stamping process of high strength steel,” Engineering Mechanics, vol. 30, no. 1, pp. 419–424, 2013. View at Publisher · View at Google Scholar · View at Scopus
  16. N. Ma, P. Hu, and K. K. Yan, “Research on boron steel for hot forming and its application,” Chinese Journal of Mechanical Engineering, no. 46, pp. 68–72, 2010. View at Google Scholar
  17. P. Hu, H. P. Liu, and Y. Q. Liu, “Numerical study on flanging and spring-back of stamped thick metal plate,” Acta Mechanica Solida Sinica, vol. 14, no. 4, pp. 290–298, 2001. View at Google Scholar · View at Scopus
  18. X. C. Wang and Y. J. Tang, “A finite element analysis of temperature fields in general shells,” Journal of Tsinghua University. Science and Technology, vol. 29, no. 5, pp. 103–112, 1989. View at Google Scholar · View at MathSciNet
  19. O. C. Zienkiewicz, R. L. Taylor, and J. Z. Zhu, The Finite Element Method: Its Basis and Fundamentals, Butterworth-Heinemann, 2005.
  20. P. Hu and Y. Tomita, “Deformation localization for plane strain tension of polymers,” Acta Mechanica Sinica, vol. 12, no. 5, pp. 564–574, 1996. View at Google Scholar