Table of Contents Author Guidelines Submit a Manuscript
Mathematical Problems in Engineering
Volume 2017, Article ID 6492081, 33 pages
https://doi.org/10.1155/2017/6492081
Research Article

A Refined Higher-Order Hybrid Stress Quadrilateral Element for Free Vibration and Buckling Analyses of Reissner-Mindlin Plates

1School of Science, Yanshan University, Qinhuangdao 066004, China
2Key Laboratory of Liaoning Province for Composite Structural Analysis of Aerocraft and Simulation, Shenyang Aerospace University, Shenyang 110136, China

Correspondence should be addressed to Xu Ma; nc.ude.usy@428uxam

Received 3 July 2017; Revised 20 September 2017; Accepted 6 November 2017; Published 27 November 2017

Academic Editor: Giovanni Garcea

Copyright © 2017 Tan Li et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. M. Wang, “On the necessity and sufficiency of the patch test for convergence of nonconforming finite elements,” SIAM Journal on Numerical Analysis, vol. 39, no. 2, pp. 363–384, 2001. View at Publisher · View at Google Scholar · View at MathSciNet · View at Scopus
  2. S. Cen and Y. Shang, “Developments of Mindlin-Reissner plate elements,” Mathematical Problems in Engineering, vol. 2015, Article ID 456740, 2015. View at Publisher · View at Google Scholar · View at Scopus
  3. J. Robinson and G. W. Haggenmacher, “LORA-an accurate four node stress plate bending element,” International Journal for Numerical Methods in Engineering, vol. 14, no. 2, pp. 296–306, 1979. View at Publisher · View at Google Scholar · View at Scopus
  4. E. Hinton and H. C. Huang, “A family of quadrilateral Mindlin plate elements with substitute shear strain fields,” Computers & Structures, vol. 23, no. 3, pp. 409–431, 1986. View at Publisher · View at Google Scholar · View at Scopus
  5. O. C. Zienkiewicz, R. L. Taylor, and J. M. Too, “Reduced integration technique in general analysis of plates and shells,” International Journal for Numerical Methods in Engineering, vol. 3, no. 2, pp. 275–290, 1971. View at Publisher · View at Google Scholar · View at Scopus
  6. E. D. L. Pugh, E. Hinton, and O. C. Zienkiewicz, “A study of quadrilateral plate bending elements with ‘reduced’ integration,” International Journal for Numerical Methods in Engineering, vol. 12, no. 7, pp. 1059–1079, 1978. View at Publisher · View at Google Scholar · View at Scopus
  7. T. J. R. Hughes, M. Cohen, and M. Haroun, “Reduced and selective integration techniques in the finite element analysis of plates,” Nuclear Engineering and Design, vol. 46, no. 1, pp. 203–222, 1978. View at Publisher · View at Google Scholar · View at Scopus
  8. T. J. R. Hughes and T. E. Tezduyar, “Finite elements based upon Mindlin plate theory with particular reference to the four-node bilinear isoparametric element,” Transactions ASME—Journal of Applied Mechanics, vol. 48, no. 3, pp. 587–596, 1981. View at Publisher · View at Google Scholar · View at Scopus
  9. T. Belytschko, C. S. Tsay, and W. K. Liu, “A stabilization matrix for the bilinear Mindlin plate element,” Computer Methods Applied Mechanics and Engineering, vol. 29, no. 3, pp. 313–327, 1981. View at Publisher · View at Google Scholar · View at MathSciNet · View at Scopus
  10. J.-L. Batoz and P. Lardeur, “A discrete shear triangular nine d.o.f. element for the analysis of thick to very thin plates,” International Journal for Numerical Methods in Engineering, vol. 28, no. 3, pp. 533–560, 1989. View at Publisher · View at Google Scholar · View at MathSciNet
  11. J.-L. Batoz and I. Katili, “On a simple triangular reissner/mindlin plate element based on incompatible modes and discrete constraints,” International Journal for Numerical Methods in Engineering, vol. 35, no. 8, pp. 1603–1632, 1992. View at Publisher · View at Google Scholar · View at Scopus
  12. K.-J. Bathe, A. Iosilevich, and D. Chapelle, “Evaluation of the MITC shell elements,” Computers & Structures, vol. 75, no. 1, pp. 1–30, 2000. View at Publisher · View at Google Scholar · View at Scopus
  13. A. K. Soh, Z. F. Long, and S. Cen, “A new nine dof triangular element for analysis of thick and thin plates,” Computational Mechanics, vol. 24, no. 5, pp. 408–417, 1999. View at Publisher · View at Google Scholar · View at Scopus
  14. A.-K. Soh, S. Cen, Y.-Q. Long, and Z.-F. Long, “A new twelve {DOF} quadrilateral element for analysis of thick and thin plates,” European Journal of Mechanics - A/Solids, vol. 20, no. 2, pp. 299–326, 2001. View at Publisher · View at Google Scholar · View at MathSciNet · View at Scopus
  15. C. Wanji and Y. K. Cheung, “Refined quadrilateral element based on Mindlin/Reissner plate theory,” International Journal for Numerical Methods in Engineering, vol. 47, no. 1-3, pp. 605–627, 2000. View at Publisher · View at Google Scholar · View at MathSciNet · View at Scopus
  16. C. Wanji and Y. K. Cheung, “Refined 9-Dof triangular Mindlin plate elements,” International Journal for Numerical Methods in Engineering, vol. 51, no. 11, pp. 1259–1282, 2001. View at Publisher · View at Google Scholar · View at Scopus
  17. S. Cen, Y.-Q. Long, Z.-H. Yao, and S.-P. Chiew, “Application of the quadrilateral area co-ordinate method: a new element for Mindlin-Reissner plate,” International Journal for Numerical Methods in Engineering, vol. 66, no. 1, pp. 1–45, 2006. View at Publisher · View at Google Scholar · View at Scopus
  18. C. Wang, X. Wang, X. Zhang, and P. Hu, “Assumed stress quasi-conforming technique for static and free vibration analysis of Reissner-Mindlin plates,” International Journal for Numerical Methods in Engineering, 2017. View at Publisher · View at Google Scholar · View at Scopus
  19. W. Chen, “Enhanced patch test of finite element methods,” Science China Physics, Mechanics & Astronomy, vol. 49, no. 2, pp. 213–227, 2006. View at Publisher · View at Google Scholar · View at Scopus
  20. W. Chen, J. Wang, and J. Zhao, “Functions for patch test in finite element analysis of the Mindlin plate and the thin cylindrical shell,” Science China Physics, Mechanics & Astronomy, vol. 52, no. 5, pp. 762–767, 2009. View at Publisher · View at Google Scholar · View at Scopus
  21. G. Jelenić and E. Papa, “Exact solution of 3D Timoshenko beam problem using linked interpolation of arbitrary order,” Archive of Applied Mechanics, vol. 81, no. 2, pp. 171–183, 2011. View at Publisher · View at Google Scholar · View at Scopus
  22. T. Li, X. Ma, J. Xili, and W. Chen, “Higher-order hybrid stress triangular Mindlin plate element,” Computational Mechanics, vol. 58, no. 6, pp. 911–928, 2016. View at Publisher · View at Google Scholar · View at MathSciNet · View at Scopus
  23. T. Li, Z. Qi, X. Ma, and W. Chen, “Higher-order assumed stress quadrilateral element for the Mindlin plate bending problem,” Structural Engineering and Mechanics, vol. 54, no. 3, pp. 393–417, 2015. View at Publisher · View at Google Scholar · View at Scopus
  24. W. J. Chen and Y. K. Cheung, “The Non-Conforming Nine-Parameters Triangular Element for Thin Plate Bending and Vibration Analysis,” in Proc. COCMSGE, P. K. K. Lee, L. G. Than, and Y. K. Cheung, Eds., pp. 1580–1583, Hong Kong, December 1994. View at Google Scholar
  25. Y. K. Cheung and W. J. Chen, “Refined nine-parameter triangular thin plate bending element by using refined direct stiffness method,” International Journal for Numerical Methods in Engineering, vol. 38, no. 2, pp. 283–298, 1995. View at Publisher · View at Google Scholar · View at MathSciNet · View at Scopus
  26. X. Ma and W. Chen, “Refined 18-DOF triangular hybrid stress element for couple stress theory,” Finite Elements in Analysis and Design, vol. 75, pp. 8–18, 2013. View at Publisher · View at Google Scholar · View at MathSciNet
  27. K. M. Liew, K. C. Hung, and M. K. Lim, “Vibration of mindlin plates using boundary characteristic orthogonal polynomials,” Journal of Sound and Vibration, vol. 182, no. 1, pp. 77–90, 1995. View at Publisher · View at Google Scholar · View at Scopus
  28. T. H. H. Pian, “Derivation of element stiffness matrices by assumed stress distributions,” AIAA Journal, vol. 2, no. 7, pp. 1333–1336, 1964. View at Publisher · View at Google Scholar
  29. T. H. H. Pian, “Element stiffness matrices for boundary compatibility and for prescribed boundary stresses,” in Proceedings of the 1st Conf. on Matrix Methods in Struct, pp. 457–477, 1965.
  30. D. S. Malkus and T. J. R. Hughes, “Mixed finite element methods—reduced and selective integration techniques: a unification of concepts,” Computer Methods Applied Mechanics and Engineering, vol. 15, no. 1, pp. 63–81, 1978. View at Publisher · View at Google Scholar · View at Scopus
  31. P. Tong, “A family of hybrid plate elements,” International Journal for Numerical Methods in Engineering, vol. 18, no. 10, pp. 1455–1468, 1982. View at Publisher · View at Google Scholar · View at Scopus
  32. K. Y. Sze, Q. H. Zhang, and G. H. Liu, “Hybrid quadrilateral finite element models for axial symmetric Helmholtz problem,” Finite Elements in Analysis and Design, vol. 52, pp. 1–10, 2012. View at Publisher · View at Google Scholar · View at MathSciNet · View at Scopus
  33. H. A. Santos and J. P. Moitinho de Almeida, “A family of Piola-Kirchhoff hybrid stress finite elements for two-dimensional linear elasticity,” Finite Elements in Analysis and Design, vol. 85, pp. 33–49, 2014. View at Publisher · View at Google Scholar · View at MathSciNet · View at Scopus
  34. R. E. Erkmen, “Shear deformable hybrid finite-element formulation for buckling analysis of thin-walled members,” Finite Elements in Analysis and Design, vol. 82, pp. 32–45, 2014. View at Publisher · View at Google Scholar · View at MathSciNet · View at Scopus
  35. T. Nishioka and S. N. Atluri, “Assumed stress finite element analysis of through-cracks in angle-ply laminates,” AIAA Journal, vol. 18, no. 9, pp. 1125–1132, 1980. View at Publisher · View at Google Scholar · View at Scopus
  36. J. P. Wolf, “Structural averaging of stresses in the hybrid stress model,” Aiaa Journal, vol. 10, no. 6, pp. 843–845, 2015. View at Google Scholar
  37. P. Tong, “New displacement hybrid finite element models for solid continua,” International Journal for Numerical Methods in Engineering, vol. 2, no. 1, pp. 73–83, 1970. View at Publisher · View at Google Scholar · View at Scopus
  38. K.-J. Bathe and E. N. Dvorkin, “A four-node plate bending element based on Mindlin/Reissner plate theory and a mixed interpolation,” International Journal for Numerical Methods in Engineering, vol. 21, no. 2, pp. 367–383, 1985. View at Publisher · View at Google Scholar · View at Scopus
  39. R. Ayad, G. Dhatt, and J. L. Batoz, “A new hybrid-mixed variational approach for Reissner-Mindlin plates, The MISP model,” International Journal for Numerical Methods in Engineering, vol. 42, no. 7, pp. 1149–1179, 1998. View at Publisher · View at Google Scholar · View at MathSciNet
  40. S. Brasile, “An isostatic assumed stress triangular element for the Reissner-Mindlin plate-bending problem,” International Journal for Numerical Methods in Engineering, vol. 74, no. 6, pp. 971–995, 2008. View at Publisher · View at Google Scholar · View at Scopus
  41. A. K. Soh, L. Zhifei, and C. Song, “A Mindlin plate triangular element with improved interpolation based on Timoshenko's beam theory,” Communications in Numerical Methods in Engineering, vol. 15, no. 7, pp. 527–532, 1999. View at Publisher · View at Google Scholar · View at Scopus
  42. A. W. Leissa, Vibration of Plates, National Aeronautics and Space Administration, Washington DC, Wash, USA, 1969.
  43. T. Irie, G. Yamada, and S. Aomura, “Natural frequencies of mindlin circular plates,” Journal of Applied Mechanics, vol. 47, no. 3, pp. 652–655, 1980. View at Publisher · View at Google Scholar · View at Scopus
  44. S. P. Timoshenko and J. M. Gere, Theory of Elastic Stability, McGraw-Hill, New York, NY, USA, 1970. View at MathSciNet
  45. S. Hosseini-Hashemi, K. Khorshidi, and M. Amabili, “Exact solution for linear buckling of rectangular Mindlin plates,” Journal of Sound and Vibration, vol. 315, no. 1-2, pp. 318–342, 2008. View at Publisher · View at Google Scholar · View at Scopus
  46. S. Kitipornchai, Y. Xiang, C. M. Wang, and K. M. Liew, “Buckling of thick skew plates,” International Journal for Numerical Methods in Engineering, vol. 36, no. 8, pp. 1299–1310, 1993. View at Publisher · View at Google Scholar · View at Scopus
  47. H. Nguyen-Xuan, G. R. Liu, C. Thai-Hoang, and T. Nguyen-Thoi, “An edge-based smoothed finite element method ({ES}-{FEM}) with stabilized discrete shear gap technique for analysis of Reissner-Mindlin plates,” Computer Methods Applied Mechanics and Engineering, vol. 199, no. 9-12, pp. 471–489, 2010. View at Publisher · View at Google Scholar · View at MathSciNet · View at Scopus
  48. K. M. Liew, J. Wang, T. Y. Ng, and M. J. Tan, “Free vibration and buckling analyses of shear-deformable plates based on FSDT meshfree method,” Journal of Sound and Vibration, vol. 276, no. 3-5, pp. 997–1017, 2004. View at Publisher · View at Google Scholar · View at Scopus
  49. H. Sofuoglu and H. Gedikli, “A refined 5-node plate bending element based on Reissner-Mindlin theory,” Communications in Numerical Methods in Engineering, vol. 23, no. 5, pp. 385–403, 2007. View at Publisher · View at Google Scholar · View at Scopus
  50. E. Hinton, T. Rock, and O. C. Zienkiewicz, “A note on mass lumping and related processes in the finite element method,” Earthquake Engineering & Structural Dynamics, vol. 4, no. 3, pp. 245–249, 1976. View at Publisher · View at Google Scholar · View at Scopus
  51. F. Wu, G. R. Liu, G. Y. Li, A. G. Cheng, and Z. C. He, “A new hybrid smoothed FEM for static and free vibration analyses of Reissner-Mindlin Plates,” Computational Mechanics, 2014. View at Publisher · View at Google Scholar · View at Scopus
  52. S. J. Lee, “Free vibration analysis of plates by using a four-node finite element formulated with assumed natural transverse shear strain,” Journal of Sound and Vibration, vol. 278, no. 3, pp. 657–684, 2004. View at Publisher · View at Google Scholar · View at Scopus
  53. O. G. McGee, A. W. Leissa, and C. S. Huang, “Vibrations of cantilevered skewed trapezoidal and triangular plates with corner stress singularities,” International Journal of Mechanical Sciences, vol. 34, no. 1, pp. 63–84, 1992. View at Publisher · View at Google Scholar · View at Scopus
  54. T. Mlzusawa, “Vibration of rectangular mindlin plates with tapered thickness by the spline strip method,” Computers & Structures, vol. 46, no. 3, pp. 451–463, 1993. View at Publisher · View at Google Scholar · View at Scopus
  55. T. Q. Bui, M. N. Nguyen, and C. Zhang, “Buckling analysis of Reissner-Mindlin plates subjected to in-plane edge loads using a shear-locking-free and meshfree method,” Engineering Analysis with Boundary Elements, vol. 35, no. 9, pp. 1038–1053, 2011. View at Publisher · View at Google Scholar · View at MathSciNet · View at Scopus
  56. C. M. Wang, S. Kitipornchai, Y. Xiang, and K. M. Liew, “Stability of skew mindlin plates under isotropic in-plane pressure,” Journal of Engineering Mechanics, vol. 119, no. 2, pp. 393–401, 1993. View at Publisher · View at Google Scholar · View at Scopus
  57. S. F. Li and W. K. Liu, Meshfree Particle Method, Springer, Berlin, Heidelberg, NY, 2004.