Crack Prediction Based on Wavelet Correlation Analysis Least Squares Support Vector Machine for Stone Cultural Relics

Liu, Bao; Ye, Fei; Mu, Kun; Wang, Jingting; Zhang, Jinyu

doi:https://doi.org/10.1155/2021/6638521

Mathematical Problems in Engineering

On this page

Abstract Introduction Results and Discussion Conclusions Data Availability Conflicts of Interest Acknowledgments References Copyright Related Articles

Research Article | Open Access

Volume 2021 | Article ID 6638521 | https://doi.org/10.1155/2021/6638521

Crack Prediction Based on Wavelet Correlation Analysis Least Squares Support Vector Machine for Stone Cultural Relics

Bao Liu,¹Fei Ye,¹Kun Mu,¹Jingting Wang,²and Jinyu Zhang³

Academic Editor: Nhon Nguyen Thanh

Received06 Nov 2020

Revised20 Jan 2021

Accepted22 Jan 2021

Published31 Jan 2021

Abstract

Preventive protection of cultural relics is to make use of all the science and technology beneficial to the research and protection of archaeological heritage to predict the disease of cultural relics. The existing preventive cultural relics protection system has made some achievements in environmental monitoring, but the analysis and utilization of large data of cultural relics are still insufficient. In this paper, under the idea of multisource information fusion, a least squares support vector machine regression method based on multivariate time series wavelet correlation analysis is proposed to achieve accurate crack prediction of stone cultural relics. Firstly, the correlation of multivariate time series of stone cultural relics are quantitatively analyzed and the validity of characteristic variables of the crack is discriminated by wavelet correlation analysis; then, a least squares support vector machine prediction model is constructed based on the correlation obtained from the analysis; finally, the good performance of the method is verified by using the environmental monitoring data of the rock mass fracture in the North Qianfo Cliff of Dafo Temple in Binzhou City of Shaanxi Province. The experimental results show that the proposed method is more effective than the traditional backpropagation neural network, support vector machine, and relevance vector machine regression methods. This method is universal and easy to implement for multisource data prediction of nonmovable cultural relics diseases. It provides a scientific theoretical reference for the preventive protection of cultural relics.

1. Introduction

Immovable cultural relics refer to ancient cultural sites, ancient tombs, ancient buildings, cave temples, stone carvings, murals, important modern historical sites, and representative buildings. The protection of cultural heritage is not only the foundation of maintaining the world cultural diversity and inheriting human civilization but also the responsibility of mankind [1, 2].

Immovable cultural relics diseases are mainly influenced by natural and man-made environmental factors [3]. These datasets of environmental factors are monitored by sensors and usually stored in the form of multiple time series; these environmental factors include wind speed, temperature, humidity, and light, which are usually characterized by high dimensions, complex correlations, and nonlinearity. It is found that nonmovable cultural relics diseases have a specific correlation with the environment in which they live. However, at present, research studies usually start only from a single attribute and carry out the visual display of multiple time series and diseases of cultural relics, without in-depth research on correlation analysis and multiattribute fusion of a large number of multisource data collected, so the disease degree of cultural relics cannot be accurately predicted.

On the one hand, according to different disciplines, current correlation analysis research methods can be divided into data mining methods, statistical methods, wavelet correlation analysis (WCA), correlation analysis based on mutual information [4–9], and so forth. WCA is based on the wavelet transform with a finite length of attenuation [10–15]. In this way, not only the frequency can be obtained, but also the time can be located; that is, the time-frequency analysis of the signal can be carried out [16, 17]. Therefore, in view of the nonlinear and nonstationary characteristics of the immovable relic disease data series, the quantitative correlation between the independent variables of environmental characteristics and the dependent variables of the disease can be obtained by WCA. On the other hand, the disease prediction of immovable cultural relics is still in its infancy; then, the existing prediction methods are all based on the backpropagation neural network (BPNN) [18, 19], support vector machine (SVM) [20, 21], and relevance vector machine (RVM) [22, 23]. However, BPNN is of the gradient descent method to obtain the minimum value of the objective function, which is easy to fall into the local optimum. For SVM, the VC dimension theory of statistical learning theory and structural risk minimization is adopted to avoid the problem of local optimal [24], but when the sample data are too much, the training time of the prediction model will be too long. For RVM, the single kernel function results in the mutual exclusion of learning ability and generalization ability. Therefore, with the rapid development of artificial intelligence technology, it is urgent to introduce a multisource information fusion algorithm to quickly and efficiently predict diseases accurately [25–27].

This paper proposes a least squares support vector machine (LSSVM) regression method based on WCA of multiple time series, which predicts accurately the diseases of immovable cultural relics. The WCA was used to identify the validity of the characteristic variables of cultural relics in addition to realize the normalization of data and dimension reduction of independent variables. LSSVM transforms the quadratic convex optimization problem of SVM into solving linear equations, which greatly reduces the difficulty of training. Moreover, through the experiment proved the superiority of the method proposed by this paper, the precise prediction of stone cultural relics crack has been realized, and a solid theoretical guidance has been provided for the concept of cultural relics protection, which is both “rescue” and “preventive”.

Compared with the existing crack prediction methods of stone cultural relics, this paper has the following innovation points.(i)The main factors affecting stone cultural relics crack are obtained quantitatively by the WCA method, and the dimension reduction of data is realized without affecting the prediction accuracy of the model.(ii)A method of stone cultural relics crack prediction based on wavelet correlation analysis least squares support vector machine is proposed, and the prediction model is established to achieve accurate prediction of stone cultural relics crack degree.(iii)The proposed method in this paper is compared with the traditional immovable cultural relics disease prediction methods based on BPNN, SVM, and RVM. Experimental results show that this method not only reduces the consumption of prediction but also has higher prediction accuracy than other traditional machine learning models.

2. Preprocessing of Stone Cultural Relics Environment Data

The monitoring data of stone cultural relics can be divided into independent variable and dependent variable multivariate time series. The independent variable sequence refers to the environmental data, while the dependent variable sequence can be regarded as the prediction quantity based on the independent variable sequence (such as the degree and type of disease). In this paper, the disease refers to the crack. Due to the diversity, complexity, and redundancy of environmental data, as well as the different units and value ranges of each variable attribute, the preprocessing of environmental data of stone cultural relics can be divided into two steps: (I) data normalization [28] and (II) dimension reduction of independent variables.

2.1. Normalization of Environmental Data of Stone Cultural Relics

Let the independent variable matrix of the environmental data be ,where is the observed column variable of environmental attributes (see, e.g., temperature, humidity, and other parameters) and is an independent variable in the multivariate time series; is the time variable.

Similarly, let the dependent variable matrix of cultural relics disease be ,where is a column variable of relics disease data (see, e.g., crack) and a dependent variable in a multivariate time series.

The normalized processing formula of the data is as follows:

The normalized multivariate time series matrix is represented by and :

The normalized data not only maintain the diversity of its properties, but also eliminate differences in value range between different attributes.

2.2. Independent Variable Dimension Reduction Based on WCA

The diseases of immovable cultural relics are affected by a variety of environmental variables, and the multivariate time series composed of these environmental variables are characterized by nonlinearity, uncertainty, redundancy, and nonstationarity. In order to reduce the consumption of predictive modeling, it is necessary to determine the principal components related to diseases. Therefore, dimension reduction of independent variables based on WCA is required for environment variables.

2.2.1. Wavelet Correlation Analysis Method

is defined as the space of measurable and square-integrable functions on the real axis. For time series , the continuous wavelet transform formula [29] iswhere is obtained by continuous wavelet transformation of the wavelet coefficient of , is the time-scale factor, is the time-position factor, and is the complex conjugate function of . Among them,where is the wavelet function; that is, the wavelet basis function is scaled and shifted.

Wenyi Chen gave the definition of the mutual wavelet transform of two time series [30], and the formula iswhere represents the wavelet transform of time series in scale factor and time-position factor , represents the wavelet transform of time series in scale factor and time position factor , and is the complex conjugate of .

Scholars like Yanfang Sang and Dong Wang gave the definition of wavelet correlation number [10, 26, 28]:where is the cross covariance of wavelet, and the formula iswhere is the wavelet correlation coefficient of and at scale factor and hysteresis factor , is the mean value of variables in parentheses, and is the real part of results in parentheses.

The range of the above formula is between [−1, 1], which represents the correlation coefficient between the independent variable and the dependent variable . “−1” means completely negative correlation, “0” means noncorrelation, and “1” means completely positive correlation.

Based on the theoretical knowledge of wavelet correlation analysis and the collected multicharacteristic environmental variables, the variables of multitime series can be reduced. The reduced variables are the key factors affecting the diseases of cultural relics. Modeling on this basis can greatly reduce the consumption of prediction without significantly affecting the prediction results.

2.2.2. Data Dimensionality Reduction Based on WCA and Stepwise Regression Forward Algorithm

The wavelet correlation analysis method is adopted to calculate the correlation coefficient matrix between the normalized multivariate time series independent variable and the dependent variable using formula (8), denoted as , as follows [28]:where is a column vector, where each element represents, respectively, the correlation coefficients of each variable in and .

The dimensionality reduction process of the independent variables adopts the algorithm of stepwise regression forward, records as the set of normalized variables, is the number of input variables, and is the set of independent variables after dimension reduction. According to the theory of wavelet correlation analysis, the dimensionality reduction process of multivariate time series is as follows:(i)Initialization operation: set normalized as and H as empty set.(ii)Based on formula (8), the wavelet correlation coefficient between input and output variables is calculated, and is obtained.(iii)Take the maximum correlation coefficient variable attribute , .(iv)According to the prediction model, the root mean square error of the prediction results is obtained by calculating the set of independent variables as the input variable, where , in which refers to the number of test samples, is the real value, and is the predictive value.(v)Select one of the remaining variables in the set to be added to and calculate ,. If , then ; otherwise will not be updated.(vi)Repeat steps iv and v until all variables in are traversed to complete the dimension reduction operation. The set of independent variables after dimension reduction is obtained, and the variables are the input of the prediction model.

The purpose of dimensionality reduction of the independent variable is to reduce redundant variables, which improves the accuracy of the prediction model and provides scientific theoretical guidance for reducing equipment investment in data collection.

3. Stone Cultural Relics Crack Prediction

SVM, which originated from the new statistical theory [31–33] in the 1990s, is a commonly used model in machine learning. It can not only be used for the classification of nonlinear samples but also be applied to the field of regression prediction. It adopts the VC dimension theory of statistical learning theory and minimizes the structural risk, avoiding the problem of local optimization. However, the more the sample data is, the longer the training time of the prediction model becomes. Therefore, this paper proposes to use the LSSVM to accurately predict the crack of stone cultural relics [34–37]. The loss function is not only related to partial support vector samples, but also to learn all samples, so as to correct the fitting error, which greatly improves the prediction accuracy. LSSVM transforms the quadratic convex optimization problem of the support vector machine into solving linear equations, which greatly reduces the difficulty of training [38–43]. References [41, 42] discussed the use of the LSSVM model for power module fault prediction and short-term traffic flow prediction. The prediction accuracy and training efficiency of the LSSVM model are much higher than those of standard SVM and BPNN, and reference [43] compared the prediction performance of tunnel boring machine in rock tunnel construction with LSSVM and RVM. It is clear that the method proposed in this paper is also effective and feasible in fault prediction and engineering.

3.1. LSSVM Prediction Modeling

Under the condition that the learning samples are known, the LSSVM algorithm can map the nonlinearity samples to the high-dimensional feature space through the kernel function. The optimal decision function is constructed in high-dimensional feature space:where is the weight matrix, is the kernel function, is the displacement, is the relaxation factor, and is the input sample; the LSSVM model controls the error of all samples learning; and according to the principle of structural risk minimization, the regression problem is expressed as a constrained optimization problem:where is the regularization parameter, is the objective function, and the following Lagrangian functions are constructed:where is the Lagrange multiplier. Find the partial derivatives of for , set the partial derivatives equal to 0, and then obtain the linear equations:where , , , refers to the inner product of the kernel function, and . The kernel function is to map the nonlinear sample set in a low-dimensional space to a high-dimensional feature space, so as to transform the nonlinear problem in the low-dimensional space into a linear problem which is in a high-dimensional space [42]. The kernel function avoids the time-consuming inner product operation in a high-dimensional space [40]. At present, the kernel functions commonly used include linear kernel function, polynomial kernel function, and radial basis function (RBF). [40–42]. Among them, linear and polynomial kernel functions belong to global kernel functions, which have strong generalization ability, but its ability of nonlinear approximation is poor, and learning abilities are not strong. RBF kernel function belongs to the local kernel function, which has strong nonlinear approximation and learning abilities. Selecting the RBF kernel function to train the LSSVM model can obtain better overall performance than other types of the kernel function. Therefore, the RBF kernel function is used to train the LSSVM model in this paper. The specific form of the RBF kernel function is as follows:where is the parameter of the kernel function, according to formula (14):

Then, the analytical solution of LSSVM is

According to the above model theory, the process first maps nonlinear sample data to high-dimensional space through the nuclear functions and then by LSSVM regression model to forecast that the LSSVM not only has the advantages of SVM but also solves the inequality constraints of the standard SVM and the secondary planning problem into the solution of the linear equation system. This improves the speed of computation and can be applied to many engineering fields.

3.2. Wavelet Correlation Analysis LSSVM-Based Crack Prediction

The structure of the model for crack prediction of stone cultural relics based on wavelet correlation analysis least squares support vector machine is shown in Figure 1.

Firstly, WCA is used to obtain the main factors affecting the crack of stone cultural relics, and the training set and test set are divided according to the main factors. Then, the RBF kernel function is selected as the kernel function of LSSVM, and the prediction model is trained repeatedly with the training set, and the regularization parameter and kernel function parameter are obtained, which are 86.68 and 9.06, respectively. And the test set verifies the quality of the model.

4. Effect Analysis of Dimension Reduction of Independent Variables Based on WCA

In order to verify the effectiveness of the proposed wavelet correlation analysis LSSVM-based method for crack prediction (WCA-LSSVM-CP), it is compared with the existing method based on BPNN (WCA-BPNN-CP), standard SVM (WCA-SVM-CP), and RVM (WCA-RVM-CP). The case data set adopts the environmental monitoring data of rock mass fractures provided by Shaanxi PI Culture and Education Technology Co., LTD., including the temperature and humidity, rainfall, SO2, O3, NO2, organic volatile, light intensity, wind speed, wind direction, and crack disease data. Figure 2 shows the site map of North Qianfo Cliff of Dafo Temple, with the red box marked as the study area.

The monitoring data of rock fracture environment of Qianfo Cliff in the north of Dafo Temple is obtained through the knowledge cloud platform, which uses the Internet of things and big data technology to monitor the disease monitoring points of stone cultural relics, according to the sensors, the data collected by the acquisition instrument are uploaded to the knowledge cloud platform by wireless transmission, and the long-term monitoring data are stored in the cloud platform. The monitoring of rock crack data is collected by fracture meter sensor, as shown in Figure 3.

Table 1 shows the monitoring data of cultural relics, a total of 460 sets [28]. The value range of the monitoring data varies greatly and the units of the attributes of each variable are different. Therefore, in order to ensure the accuracy of the analysis, it is necessary to normalize the multivariate time series and and reduce the dimension.

After normalization of the cultural heritage monitoring data, by wavelet correlation analysis, the correlation coefficient matrix between environmental variable multivariate time series and heritage disease was obtained, and the results of wavelet correlation analysis are shown in Figure 4.

In Figure 4, the abscissa is the serial number of the attributes of 13 environmental variables, and the ordinate is the wavelet correlation coefficient between the environmental variables and the cracks in cultural relics [28]. Then, according to the algorithm of stepwise regression forward, the environment variable corresponding to the largest wavelet correlation coefficient is selected as the basic attribute, and all the environment variable attributes are traversed in turn according to the predicted root mean square error. Finally, the attributes of environmental variables corresponding to numbers 2, 4, 6, 11, and 13 were obtained, which corresponded to temperature, ultraviolet intensity, precipitation intensity, humidity, and dew point, respectively, and were composed into a multidimensional time series after dimension reduction, denoted as .

5. Results and Discussion

5.1. Crack Prediction Results and Discussion

The environment variable after dimension reduction was used as the input to LSSVM, BPNN, and the standard SVM and RVM prediction model. The first 405 sets of data were selected as the training samples, and the last 55 groups were the test samples. The prediction results are obtained by simulation, as shown in Figures 5 and 6.

As can be seen from Figures 5 and 6, after the dimension reduction of environmental variables is used as the input of the prediction model through wavelet correlation analysis, there are significant differences among the five methods. The error concentration of WCA-BPNN-CP is within 0.2 mm, and the absolute error of WCA-SVM-CP is less than 0.15 mm, and that of the maximum value of WCA-RVM-CP is about 0.05 mm. Although the LSSVM-CP and WCA-RVM-CP are close to WCA-LSSVM-CP, the absolute error median of WCA-LSSVM-CP is lower than that of LSSVM-CP and WCA-RVM-CP, which indicates that the prediction model after WCA not only obtains the main environmental factors affecting the crack opening disease of stone cultural relics but also improves the prediction accuracy.

5.2. Prediction Performance Evaluation

In order to further study the predictive performance of the model quantitatively, under the condition of keeping the training samples and test samples unchanged, root mean square error (RMSE), mean absolute error (MAE), mean absolute percentage error (MAPE), and determination coefficient () were used to evaluate the prediction performance of the above model:where is the predicted value, refers to the real value, and represents the average value; thus, Table 2 summarizes the comparison results of performance indexes of the five prediction models after dimension reduction of environmental variables in the wavelet correlation analysis.

Moreover, the coefficient of variation (CV) is used to analyze the stability of cultural relics crack data. The coefficient of variation is an index reflecting the degree of data dispersion [44–46]. By calculating and comparing the coefficient of variation of the machine learning prediction models in this paper, the performance of the prediction model is analyzed. The coefficient of variation is calculated as follows:where and represent the standard deviation and average value of the fracture sequence of the cultural relics disease, respectively. The CV of predicted values of each model is also shown in Table 2.

It can be seen from Table 2 that, under the same conditions, in terms of the determination coefficient , of WCA-LSSVM-CP is close to 1, and the effect is the best, of WCA-RVM-CP model is 0.9870, LSSVM-CP is 0.9823, and that of WCA-SVM-CP is 0.8583, followed by the WCA-BPNN-CP model. The RMSE, MAE, and MAPE of WCA-RVM-CP model are basically 1/4 of theirs, compared with BPNN model and SVM model; however, that of WCA-LSSVM-CP is less than WCA-RVM-CP. In other words, WCA-LSSVM-CP has the least error. From the four performance evaluation indexes, the predicted values of WCA-LSSVM-CP are closer to the real value. Finally, the CV of the proposed method is 21.72%, which is the closest to the true value of the CV; that is to say, the stability of WCA-LSSVM-CP predicted values can reflect the real stability of the cultural relics crack. Therefore, it shows that the WCA-LSSVM-CP model has better prediction performance and is more suitable for the prediction of the degree of stone cultural relics crack.

6. Conclusions

Aiming at the deficiency of analyzing the large data of stone cultural relics, this paper proposes the LSSVM method for predicting the crack of stone cultural relics based on multivariate time series WCA. Firstly, the cultural relics monitoring data is normalized, and then the WCA and stepwise regression forward algorithm are used to reduce the dimension of the environmental variables. On the premise that the prediction accuracy is not significantly affected, the independent variables and the prediction consumption are reduced. Secondly, the WCA-LSSVM-CP method is proposed to predict the crack of stone cultural relics. Finally, the real case is used for effect comparison, and the experimental results show that the method in this paper can predict the crack of stone cultural relics accurately.

The parameters values of the WCA-LSSVM-CP model presented in this paper are only for the case of the Dafo Temple. Like most machine learning methods, the model parameters of LSSVM are the key factors affecting the prediction effect of the model, which need to be determined through data experiments for specific scenarios.

Finally, the proposed method is suitable for disease prediction of immovable cultural relics by multivariate time series environmental variables. It is universal and easy to implement, which provides a scientific theoretical reference for the preventive protection of cultural relics and can be extended to other aspects of cultural relics protection.

Data Availability

The data that support the findings of this study are available from the corresponding author upon reasonable request.

Conflicts of Interest

The authors declare that there are no conflicts of interest regarding the publication of this paper.

Acknowledgments

This research was supported in part by a grant from the National Natural Science Foundation of China (61703329), Yulin Science and Technology Plan Project (CXY-2020-037), Xi’an Science and Technology Plan Project (2020KJRC0068), Scientific Research Program funded by Shaanxi Provincial Education Department (18JK1005), the 13th Five-Year Plan of Education Science in Shaanxi Province (SGH18H159), Key R & D projects of Shaanxi Province (2019GY-097), and Key Industrial Chain Projects Of Shaanxi Province (2019ZDLGY15-04-02).

References

T. B. Chen and L. J. Wang, “Ten years plan for the protection of immovable cultural relics,” Chinese Cultural Heritage, vol. 3, pp. 108–111, 2004.
View at: Google Scholar
M. Jennifer, “Relics, reinvention, and reform in Renaissance Venice: Catherine of Siena’s stigmata at the Basilica Dei Santi Giovanni e Paolo,” Renaissance Studies, vol. 34, no. 2, pp. 282–284, 2020.
View at: Google Scholar
X. Wang, “Study on the crisis and countermeasure of rural red cultural relics protection in northwest China,” in Proceedings of 2017 International Conference on Social Sciences, Arts and Humanities (SSAH 2017), pp. 198–202, Harbin, China, September 2017.
View at: Google Scholar
J. Y. Jong, C. H. Rim, M. S. Choi, and H. C. Om, “Comprehensive evaluation of marine waste heat recovery technologies based on Hierarchy-Grey correlation analysis,” Journal of Ocean Engineering and Science, vol. 4, no. 4, pp. 308–316, 2019.
View at: Google Scholar
H. Yamamoto, H. Yamaji, E. Fukusaki, H. Ohno, and H. Fukuda, “Canonical correlation analysis for multivariate regression and its application to metabolic fingerprinting,” Biochemical Engineering Journal, vol. 40, no. 2, pp. 199–204, 2008.
View at: Publisher Site | Google Scholar
K. He and S. F. Chen, “Comprehensive evaluation method based on one of causal diagram and its application,” Control and Decision, vol. 25, no. 10, pp. 1513–1518, 2010.
View at: Google Scholar
R. B. Nelsen, An introduction to Copulas, Springer, Berlin, Germany, 2006.
S. Okuno, K. Aihara, and Y. Hirata, “Combining multiple forecasts for multivariate time series via state-dependent weighting,” Chaos (Woodbury, N.Y.), vol. 29, no. 3, pp. 033–128, 2019.
View at: Publisher Site | Google Scholar
J. You, Y. Kim, W. Seok et al., “Multivariate time-frequency analysis of electrohysterogram for classification of term and preterm labor,” Journal of Electrical Engineering & Technology, vol. 14, no. 2, pp. 897–916, 2019.
View at: Publisher Site | Google Scholar
G. Turbelin, P. Ngae, and M. Grignon, “Wavelet cross-correlation analysis of wind speed series generated by ANN based models,” Renewable Energy, vol. 34, no. 4, pp. 1024–1032, 2009.
View at: Publisher Site | Google Scholar
S. Rehman and A. H. Siddiqi, “Wavelet based correlation coefficient of time series of Saudi Meteorological Data,” Chaos, Solitons & Fractals, vol. 39, no. 4, pp. 1764–1789, 2009.
View at: Publisher Site | Google Scholar
P. M. Josué, F. M. Javier, and M. E. Martín, “Dynamic wavelet correlation analysis for multivariate climate time series,” Scientific Reports, vol. 10, no. 1, 2020.
View at: Google Scholar
A. Tankanag, G. Krasnikov, and M. Irina, “A pilot study: wavelet cross-correlation of cardiovascular oscillations under controlled respiration in humans,” Microvascular Research, vol. 130, Article ID 103993, 2020.
View at: Google Scholar
R. Perna, M. Abela, M. Mameli et al., “Flow characterization of a pulsating heat pipe through the wavelet analysis of pressure signals,” Applied Thermal Engineering, vol. 171, Article ID 115128, 2020.
View at: Publisher Site | Google Scholar
Q. F. Li, P. F. He, Y. C. He et al., “Investigation to the relation between meteorological drought and hydrological drought in the upper Shaying River Basin using wavelet analysis,” Atmospheric Research, vol. 234, Article ID 104743, 2019.
View at: Google Scholar
L. Faes, A. Porta, and G. Nollo, “Testing frequency-domain causality in multivariate time series,” IEEE Transactions on Biomedical Engineering, vol. 57, no. 8, pp. 1897–1906, 2010.
View at: Publisher Site | Google Scholar
A. Aue, S. Hörmann, L. Horváth, and M. Reimherr, “Break detection in the covariance structure of multivariate time series models,” The Annals of Statistics, vol. 37, no. 6B, pp. 4046–4087, 2009.
View at: Publisher Site | Google Scholar
D. W. Cui, “Application of hidden multilayer BP neural network model in runoff prediction,” Hydrology, vol. 33, no. 1, pp. 68–73, 2013.
View at: Google Scholar
H. Y. Yao and T. F. Zhang, “SOC estimation of battery based on improved BP neural network with momentum factor,” Battery Bimonthly, vol. 49, no. 4, pp. 309–311, 2019.
View at: Google Scholar
J. Ru, Research on the Application of Support Vector Machine in the Protection of Earth Sites, Northwestern University, Evanston, IL, USA, 2013.
Y. Sun, X. D. Feng, and L. Q. Yang, “Predicting tunnel squeezing using multiclass support vector machines,” Advances in Civil Engineering, vol. 2018, Article ID 4543984, 12 pages, 2018.
View at: Publisher Site | Google Scholar
B. Liu, K. Mu, F. Ye et al., “Immovable cultural relics disease prediction based on relevance vector machine,” Mathematical Problems in Engineering, vol. 2020, Article ID 9369781, 9 pages, 2020.
View at: Publisher Site | Google Scholar
J. Jiang, M. Li, X. Jing, and B. Lv, “Research on the performance of relevance vector machine for regression and classification,” in Proceedings of the IEEE Advanced Information Technology, Electronic and Automation Control Conference (IAEAC), pp. 758–762, Chongqing, China, December 2015.
View at: Google Scholar
J. Wang, J. Kang, and H. Liang, “Prediction of the NOx emissions from thermal power plant based on support vector machine optimized by chaos optimization algorithm,” in Proceedings of the International Conference on Intelligent Computing and Information Science (ICICIS), pp. 189–194, Chongqing, China, January 2011.
View at: Google Scholar
W. H. Xu and J. H. Yu, “A novel approach to information fusion in multi-source datasets: a granular computing viewpoint,” Information Sciences, vol. 378, pp. 410–423, 2016.
View at: Google Scholar
Y. F. Sang, D. Wang, J. C. Wu et al., “Wavelet cross-correlation method for hydrologic time series analysis,” Shuili Xuebao/Journal of Hydraulic Engineering, vol. 41, no. 11, pp. 1272–1279, 2010.
View at: Google Scholar
G. A. Bhairevi, K. Dookie, K. Nithin, S. Pijush, and P. Ramamohan Rao, “Prediction of compressive strength of self-compacting concrete using least square support vector machine and relevance vector machine,” KSCE Journal of Civil Engineering, vol. 18, no. 6, pp. 1753–1758, 2014.
View at: Google Scholar
Q. Shang, H. Q. Wang, and X. H. Zhang, “Research on wavelet-based correlation analysis and predictive modeling of multivariate time series,” Computer Knowledge & Technology, vol. 13, pp. 29–34, 2017.
View at: Google Scholar
D. B. Percival and A. T. Walden, Wavelet Methods for Time Series Analysis, Cambridge University Press, Cambridge, UK, 2000.
W. Y. Chen, “Health progress and economic growth in the USA: the continuous wavelet analysis,” Empirical Economics, vol. 50, pp. 1–25, 2015.
View at: Publisher Site | Google Scholar
B. Mallikarjuna, K. Sathish, P. V. Krishna, and R. Viswanathan, “The effective SVM-based binary prediction of ground water table,” Evolutionary Intelligence, vol. 1, pp. 1–9, 2020.
View at: Google Scholar
T. Zhou, P. Xia, H. X. Hu et al., “Application of optimized support vector machine based on wavelet decomposition in reservoir annual inflow prediction,” Journal of North China University of Water Resources and Electric Power, vol. 39, no. 3, pp. 24–30, 2018.
View at: Google Scholar
V. A. Kramar, V. V. Alchakov et al., “Application of support vector machine for prediction and classification,” Journal of Physics: Conference Series, vol. 3, pp. 1–5, 2018.
View at: Google Scholar
D. Prayogo and Y. T. T. Susanto, “Optimizing the prediction accuracy of friction capacity of driven piles in cohesive soil using a novel self-tuning least squares support vector machine,” Advances in Civil Engineering, vol. 2018, Article ID 6490169, 9 pages, 2018.
View at: Publisher Site | Google Scholar
H. M. Liu and Y. L. Xu, “Prediction of water quality based on least square support vector regression,” Computer and Modernization, vol. 9, pp. 31–34, 2019.
View at: Google Scholar
X. H. Wang and X. L. Guo, “Application of least squares support vector machine in settlement prediction,” Beijing Surveying and Mapping, vol. 33, no. 9, pp. 1087–1089, 2019.
View at: Google Scholar
N. D. Hoang, “An artificial intelligence method for asphalt pavement pothole detection using least squares support vector machine and neural network with steerable filter-based feature extraction,” Advances in Civil Engineering, vol. 2018, Article ID 7419058, 12 pages, 2018.
View at: Publisher Site | Google Scholar
K. Li, C. Liang, W. Lu, C. Li, S. Zhao, and B. Wang, “Forecasting of short-term daily tourist flow based on seasonal clustering method and PSO-LSSVM,” ISPRS International Journal of Geo-Information, vol. 9, no. 11, p. 676, 2020.
View at: Publisher Site | Google Scholar
S. G. Zhang, C. Liu, W. Wang, and B. Chang, “Twin least square support vector regression model based on Gauss-Laplace mixed noise feature with its application in wind speed prediction,” Entropy, vol. 22, no. 10, p. 1102, 2020.
View at: Publisher Site | Google Scholar
Q. Liu, Research of Time Series Prediction Method and Application Based on LS-SVM, Harbin Institute of Technology, Harbin, China, 2011.
C. Y. Zhao and P. Hu, “Application of time series prediction method based on LS-SVM in control system,” Science and Technology & Innovation, vol. 22, pp. 10-11, 2020.
View at: Google Scholar
C. Luo, Research on Short-Term Traffic Flow Prediction Method Based on Least Square Support Vector Machine, Taiyuan University of Technology, Taiyuan, China, 2019.
Y. Zhang, M. Wei, G. Su et al., “A novel intelligent method for predicting the penetration rate of the tunnel boring machine in rocks,” Mathematical Problems in Engineering, vol. 2020, Article ID 3268694, 15 pages, 2020.
View at: Publisher Site | Google Scholar
M. Choi, S. C. Porter, B. Macht, and A. Meisen, “Novel coating uniformity models for tablet pan coaters,” AAPS PharmSciTech, vol. 22, no. 7, 2021.
View at: Publisher Site | Google Scholar
X. Y. Guan, S. L. Wang, Z. Y. Gao, Y. Lv, and X. J. Fu, “Spatio-temporal variability of soil salinity and its relationship with the depth to groundwater in salinization irrigation district,” Acta Ecologica Sinica, vol. 32, no. 4, pp. 1202–1210, 2012.
View at: Google Scholar
W. Z. Feng, X. T. Wang, J. Han et al., “Research on soil salinization monitoring based on scale conversion of satellite and UAV remote sensing data,” Water Saving Irrigation, vol. 303, no. 11, pp. 87–93, 2020.
View at: Google Scholar

Copyright

Copyright © 2021 Bao Liu et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

336

Downloads

684

Citations