Table of Contents Author Guidelines Submit a Manuscript
Shock and Vibration
Volume 2014 (2014), Article ID 430854, 9 pages
http://dx.doi.org/10.1155/2014/430854
Research Article

Damage Identification of Wind Turbine Blades Using Piezoelectric Transducers

1School of Mechanical Systems Engineering, Chonnam National University, Gwangju 500-757, Republic of Korea
2Engineering Institute, MS T001, Los Alamos National Laboratory, Los Alamos, NM 87545, USA

Received 14 February 2013; Accepted 14 June 2013; Published 7 April 2014

Academic Editor: Jung-Ryul Lee

Copyright © 2014 Seong-Won Choi et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. U.S. Department of Energy, 20% Wind Energy by 2030: Increasing Wind Energy's Contribution to U.S. Electricity Supply, Wind & Hydropower Technologies Program, 2008, http://www1.eere.energy.gov/windandhydro/pdfs/41869.pdf.
  2. C. C. Ciang, J. R. Lee, and H. J. Bang, “Structural health monitoring for a wind turbine system: a review of damage detection methods,” Measurement Science and Technology, vol. 19, no. 12, Article ID 122001, 2008. View at Publisher · View at Google Scholar · View at Scopus
  3. B. Lu, Y. Li, X. Wu, and Z. Yang, “A review of recent advances in wind turbine condition monitoring and fault diagnosis,” in Proceedings of the IEEE Power Electronics and Machines in Wind Applications (PEMWA '09), pp. 1–7, Lincoln, Neb, USA, June 2009. View at Publisher · View at Google Scholar · View at Scopus
  4. N. Bourasseau, E. Moulin, C. Delebarre, and P. Bonniau, “Radome health monitoring with Lamb waves: experimental approach,” NDT and E International, vol. 33, no. 6, pp. 393–400, 2000. View at Publisher · View at Google Scholar · View at Scopus
  5. S. S. Kessler, S. M. Spearing, and C. Soutis, “Damage detection in composite materials using Lamb wave methods,” Smart Materials and Structures, vol. 11, no. 2, pp. 269–278, 2002. View at Publisher · View at Google Scholar · View at Scopus
  6. J. B. Ihn and F. K. Chang, “Detection and monitoring of hidden fatigue crack growth using a built-in piezoelectric sensor/actuator network: II. Validation using riveted joints and repair patches,” Smart Materials and Structures, vol. 13, no. 3, pp. 621–630, 2004. View at Publisher · View at Google Scholar · View at Scopus
  7. V. Giurgiutiu, A. Zagrai, and J. J. Bao, “Piezoelectric wafer embedded active sensors for aging aircraft structural health monitoring,” Structural Health Monitoring, vol. 1, no. 1, pp. 41–61, 2002. View at Google Scholar · View at Scopus
  8. M. Lemistre and D. Balageas, “Structural health monitoring system based on diffracted Lamb wave analysis by multiresolution processing,” Smart Materials and Structures, vol. 10, no. 3, pp. 504–511, 2001. View at Publisher · View at Google Scholar · View at Scopus
  9. A. Raghavan and C. E. S. Cesnik, “Review of guided-wave structural health monitoring,” Shock and Vibration Digest, vol. 39, no. 2, pp. 91–114, 2007. View at Publisher · View at Google Scholar · View at Scopus
  10. G. Park, A. C. Rutherford, J. R. Wait, B. Nadler, C. R. Farrar, and T. N. Claytor, “High-frequency response functions for composite plate monitoring with ultrasonic validation,” AIAA Journal, vol. 43, no. 11, pp. 2431–2437, 2005. View at Google Scholar · View at Scopus
  11. S. H. Diaz Valdes and C. Soutis, “Delamination detection in composite laminates from variations of their modal characteristics,” Journal of Sound and Vibration, vol. 228, no. 1, pp. 1–9, 1999. View at Google Scholar · View at Scopus
  12. H. Zhang, M. J. Schulz, A. Naser, F. Ferguson, and P. F. Pai, “Structural health monitoring using transmittance functions,” Mechanical Systems and Signal Processing, vol. 13, no. 5, pp. 765–787, 1999. View at Publisher · View at Google Scholar · View at Scopus
  13. J. P. Dunne, D. M. Pitt, K. J. Kilian, and D. A. Sofge, “Recent advances in active damage interrogation,” in Proceedings of the 42nd AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference and Exhibit Technical Papers, pp. 1937–1945, Seattle, Wash, USA, April 2001. View at Scopus
  14. G. Park, H. Sohn, C. R. Farrar, and D. J. Inman, “Overview of piezoelectric impedance-based health monitoring and path forward,” Shock and Vibration Digest, vol. 35, no. 6, pp. 451–463, 2003. View at Publisher · View at Google Scholar · View at Scopus
  15. D. Berry, Design of 9-Meter Carbon-Fiberglass Prototype Blades: CX-100 and TX-100, NM SAND2007-0201, Sandia National Laboratories, Albuquerque, NM, USA, 2007.
  16. V. Giurgiutiu, “Tuned Lamb wave excitation and detection with piezoelectric wafer active sensors for structural health monitoring,” Journal of Intelligent Material Systems and Structures, vol. 16, no. 4, pp. 291–305, 2005. View at Publisher · View at Google Scholar · View at Scopus
  17. G. Park, C. R. Farrar, A. C. Rutherford, and A. N. Robertson, “Piezoelectric active sensor self-diagnostics using electrical admittance measurements,” Journal of Vibration and Acoustics, vol. 128, no. 4, pp. 469–476, 2006. View at Publisher · View at Google Scholar · View at Scopus
  18. G. Park, C. R. Farrar, F. L. di Scalea, and S. Coccia, “Performance assessment and validation of piezoelectric active-sensors in structural health monitoring,” Smart Materials and Structures, vol. 15, no. 6, pp. 1673–1683, 2006. View at Publisher · View at Google Scholar · View at Scopus