Table of Contents Author Guidelines Submit a Manuscript
Shock and Vibration
Volume 2015, Article ID 406294, 8 pages
http://dx.doi.org/10.1155/2015/406294
Research Article

Constant Cutting Force Control for CNC Machining Using Dynamic Characteristic-Based Fuzzy Controller

Department of Mechanical Engineering, Tianjin University, Weijin Road, Tianjin 300072, China

Received 14 November 2014; Revised 26 December 2014; Accepted 26 December 2014

Academic Editor: Vadim V. Silberschmidt

Copyright © 2015 Hengli Liu et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. T.-Y. Kim and J. Kim, “Adaptive cutting force control for a machining center by using indirect cutting force measurements,” International Journal of Machine Tools and Manufacture, vol. 36, no. 8, pp. 925–937, 1996. View at Publisher · View at Google Scholar · View at Scopus
  2. C. Y. Xu and Y. C. Shin, “Control of cutting force for creep-feed grinding processes using a multi-level fuzzy controller,” Transactions of the ASME—Journal of Dynamic Systems, vol. 129, no. 4, pp. 480–492, 2007. View at Publisher · View at Google Scholar · View at Scopus
  3. D. Kim and D. Jeon, “Fuzzy-logic control of cutting forces in CNC milling processes using motor currents as indirect force sensors,” Precision Engineering, vol. 35, no. 1, pp. 143–152, 2011. View at Publisher · View at Google Scholar · View at Scopus
  4. G. D. Kim and C. N. Chu, “Indirect cutting force measurement considering frictional behaviour in a machining centre using feed motor current,” The International Journal of Advanced Manufacturing Technology, vol. 15, no. 7, pp. 478–484, 1999. View at Publisher · View at Google Scholar · View at Scopus
  5. Y.-H. Jeong and D.-W. Cho, “Estimating cutting force from rotating and stationary feed motor currents on a milling machine,” International Journal of Machine Tools and Manufacture, vol. 42, no. 14, pp. 1559–1566, 2002. View at Publisher · View at Google Scholar · View at Scopus
  6. M. Liang, T. Yeap, A. Hermansyah, and S. Rahmati, “Fuzzy control of spindle torque for industrial CNC machining,” International Journal of Machine Tools & Manufacture, vol. 43, no. 14, pp. 1497–1508, 2003. View at Publisher · View at Google Scholar · View at Scopus
  7. R. Haber-Guerra, S. Y. Liang, J. R. Alique, and R. Haber-Haber, “Fuzzy control of spindle torque in high-speed milling processes,” Journal of Manufacturing Science and Engineering, vol. 128, no. 4, pp. 1014–1018, 2006. View at Publisher · View at Google Scholar · View at Scopus
  8. U. Zuperl, F. Cus, and M. Reibenschuh, “Neural control strategy of constant cutting force system in end milling,” Robotics and Computer-Integrated Manufacturing, vol. 27, no. 3, pp. 485–493, 2011. View at Publisher · View at Google Scholar · View at Scopus
  9. U. Zuperl, “A combined system for off-line optimization and adaptive adjustment of the cutting parameters during a ball-end milling process,” Journal of Mechanical Engineering, vol. 51, no. 9, pp. 542–559, 2005. View at Google Scholar
  10. U. Zuperl, F. Cus, and M. Reibenschuh, “Modeling and adaptive force control of milling by using artificial techniques,” Journal of Intelligent Manufacturing, vol. 23, no. 5, pp. 1805–1815, 2012. View at Publisher · View at Google Scholar · View at Scopus
  11. U. Zuperl and F. Cus, “System for off-line feedrate optimization and neural force control in end milling,” International Journal of Adaptive Control and Signal Processing, vol. 26, no. 2, pp. 105–123, 2012. View at Publisher · View at Google Scholar · View at Scopus
  12. P. Benardos and G.-C. Vosniakos, “Offline flexible optimisation of feed and speed in computer numerical control machining of sculptured surfaces exploiting dedicated cutting force metamodels,” Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, vol. 228, no. 6, pp. 878–892, 2014. View at Publisher · View at Google Scholar
  13. R.-J. Lian, B.-F. Lin, and J.-H. Huang, “A grey prediction fuzzy controller for constant cutting force in turning,” International Journal of Machine Tools and Manufacture, vol. 45, no. 9, pp. 1047–1056, 2005. View at Publisher · View at Google Scholar · View at Scopus
  14. F. Ridwan, X. Xu, and F. C. L. Ho, “Adaptive execution of an NC program with feed rate optimization,” International Journal of Advanced Manufacturing Technology, vol. 63, no. 9-12, pp. 1117–1130, 2012. View at Publisher · View at Google Scholar · View at Scopus
  15. Y. S. Liao and J. C. Woo, “Design of a fuzzy controller for the adaptive control of WEDM process,” International Journal of Machine Tools and Manufacture, vol. 40, no. 15, pp. 2293–2307, 2000. View at Publisher · View at Google Scholar · View at Scopus
  16. U. Zuperl, F. Cus, and M. Milfelner, “Fuzzy control strategy for an adaptive force control in end-milling,” Journal of Materials Processing Technology, vol. 164-165, pp. 1472–1478, 2005. View at Publisher · View at Google Scholar · View at Scopus
  17. D. Li, M. Xu, C. Wei, D. Hu, and L. Xu, “A dynamic threshold-based fuzzy adaptive control algorithm for hard sphere grinding,” The International Journal of Advanced Manufacturing Technology, vol. 60, no. 9-12, pp. 923–932, 2012. View at Publisher · View at Google Scholar · View at Scopus
  18. J. Lin and R.-J. Lian, “Hybrid self-organizing fuzzy and radial basis-function neural-network controller for constant cutting force in turning,” The International Journal of Advanced Manufacturing Technology, vol. 53, no. 9–12, pp. 921–933, 2011. View at Publisher · View at Google Scholar · View at Scopus
  19. M.-Y. Yang and T.-M. Lee, “Hybrid adaptive control based on the characteristics of CNC end milling,” International Journal of Machine Tools and Manufacture, vol. 42, no. 4, pp. 489–499, 2002. View at Publisher · View at Google Scholar · View at Scopus
  20. S.-J. Kim, H. U. Lee, and D.-W. Cho, “Prediction of chatter in NC machining based on a dynamic cutting force model for ball end milling,” International Journal of Machine Tools and Manufacture, vol. 47, no. 12-13, pp. 1827–1838, 2007. View at Publisher · View at Google Scholar · View at Scopus