Table of Contents Author Guidelines Submit a Manuscript
Shock and Vibration
Volume 2016, Article ID 4847250, 8 pages
http://dx.doi.org/10.1155/2016/4847250
Research Article

Dynamic Efficiency of a Container Crane’s Hoisting Transmission System under Hoisting Dynamic Load

College of Mechanical Engineering, Tongji University, Shanghai 200092, China

Received 8 January 2016; Revised 16 February 2016; Accepted 17 February 2016

Academic Editor: Sergio De Rosa

Copyright © 2016 Yuanyuan Liu et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. B. R. Hohn, K. Michaelis, and T. Vollmer, “Thermal rating of gear drives: balance between power loss and heat dissipation,” AGMA Technical Paper, 1996. View at Google Scholar
  2. C. M. C. G. Fernandes, P. M. T. Marques, R. C. Martins, and J. H. O. Seabra, “Gearbox power loss. Part II: friction losses in gears,” Tribology International, vol. 88, pp. 309–316, 2015. View at Publisher · View at Google Scholar · View at Scopus
  3. C. M. C. G. Fernandes, P. M. T. Marques, R. C. Martins, and J. H. Seabra, “Gearbox power loss. Part III: application to a parallel axis and a planetary gearbox,” Tribology International, vol. 88, pp. 317–326, 2015. View at Publisher · View at Google Scholar
  4. B. R. Höhn, K. Michaelis, and M. Hinterstoißer, “Optimization of gearbox efficiency,” Goriva I Maziva, vol. 48, no. 4, pp. 441–480, 2009. View at Google Scholar
  5. C. M. C. G. Fernandes, P. M. T. Marques, R. C. Martins, and J. H. O. Seabra, “Gearbox power loss. Part I: losses in rolling bearings,” Tribology International, vol. 88, pp. 298–308, 2015. View at Publisher · View at Google Scholar · View at Scopus
  6. SKF General Catalogue 6000 EN, SKF Group, Goteborg, Sweden, 2005.
  7. F. Concli and C. Gorla, “Computational and experimental analysis of the churning power losses in an industrial planetary speed reducer,” in Proceedings of the 9th International Conference on Advances in Fluid Mechanics-Advances in Fluid Mechanics IX, vol. 74 of WIT Transactions on Engineering Sciences, 2012.
  8. C. Changenet and P. Velex, “A model for the prediction of churning losses in geared transmissions—preliminary results,” Journal of Mechanical Design, vol. 129, no. 1, pp. 128–133, 2007. View at Publisher · View at Google Scholar · View at Scopus
  9. P. M. T. Marques, C. M. C. G. Fernandes, R. C. Martins, and J. H. O. Seabra, “Power losses at low speed in a gearbox lubricated with wind turbine gear oils with special focus on churning losses,” Tribology International, vol. 62, pp. 186–197, 2013. View at Publisher · View at Google Scholar · View at Scopus
  10. H. Xu, A. Kahraman, N. E. Anderson, and D. G. Maddock, “Prediction of mechanical efficiency of parallel-axis gear pairs,” Journal of Mechanical Design, vol. 129, no. 1, pp. 58–68, 2007. View at Publisher · View at Google Scholar · View at Scopus
  11. G. Jia-Shun, W. San-Min, and Y. Ru, “Dynamic efficiency investigation of the transmission of tilt-totor,” Journal of Aerospace Power, vol. 25, no. 8, pp. 1894–1899, 2010. View at Google Scholar