Analysis and Experimental Study on Pressure Characteristics of Supporting Roller Group of Pipe Belt Conveyor

Wang, Shuang; Li, Deyong; Hu, Kun

doi:https://doi.org/10.1155/2019/7061847

Shock and Vibration

On this page

Abstract Introduction Conclusions Data Availability Conflicts of Interest Authors’ Contributions Acknowledgments References Copyright Related Articles

Research Article | Open Access

Volume 2019 | Article ID 7061847 | https://doi.org/10.1155/2019/7061847

Analysis and Experimental Study on Pressure Characteristics of Supporting Roller Group of Pipe Belt Conveyor

Shuang Wang,^1,2Deyong Li ,²and Kun Hu^1,2

Academic Editor: Roberto Nascimbene

Received12 Apr 2019

Revised19 Jul 2019

Accepted22 Jul 2019

Published01 Aug 2019

Abstract

Aiming at the problem in measuring the nonuniformly distributed pressure generated by the pipe belt conveyor when conveying raw coals, a hexagonal adjustable pressure measuring device for the idler group is proposed. The dynamic model of the pipe belt conveyor clamping-type roller group is established. In order to simplify the calculation process of mechanical analysis, the modal analysis is carried out to determine the factors which will influence the pressure. The pipe diameter and filling rate are selected as the key control factors by the sensitive analysis of pressure of the pipe belt conveyor clamping type roller group. An adjustable diameter-type supporting roller group experiment device is self-designed, and the dynamic pressure change of the roller group and each roller pressure are tested. The results show that the average error between the simulated and tested values of the pressure of the idler group at different filling rates is 7.3%; the theoretical and simulated values of the pressure of the idler group are in good agreement with the experimental values. The study provides a theoretical basis and experimental reference for the design and application of pipe belt conveyors.

1. Introduction

Nowadays, countries around the world are shifting towards a development model highlighted by green ecology and low carbon [1]. However, the environmental pollution, which is caused by a large amount of dust and scattering granules generated by the bulk material transfer system during work, has raised more and more attention in the conveyor industry around the world [2]. Many countries have proposed the use of environmentally friendly pipe belt conveyors to reduce the environmental pollution from the conveying process [3, 4]. Moreover, a pipe belt conveyor has shown great development prospects [5] because it overcomes the shortcomings of the traditional belt conveyor, such as the susceptibility of generating dust and scattering granules, the vulnerability to which it is hampered by spatial restrictions, and the small turning inclination angle [6].

The conveyor belt of the pipe belt conveyor is guided by the idler [7]. Also, the flat belt passing through the roller gradually takes the shape of a pipe belt to increase the enveloping surface of the conveyor belt to the material and ensure the enclosed conveying of the material [8]. Zamiralova et al. studied the rotational resistance of the idlers of the pipe belt conveyer and reduced the resistance of the idler during the conveying process [9, 10]. The comparative analysis between the force distribution of the pipe belt conveyer under no load and that of the traditional belt conveyor was conducted, and the dynamic wear analysis of the rubber conveyor belt of the pipe belt conveyer was performed by Fedorko et al. [11, 12]. Molnár et al. presents design and verification of regression models for prediction of pipe conveyor belt contact forces on idler rolls. Several criteria have been used to verify the presented regression models [13, 14]. Lodewijks tested the rolling resistance coefficient between the rubber conveyor belt and the idlers and investigated the turning characteristics involving large inclination angle of the round belt conveyor [15, 16]. Professor Weigang Song pointed out the unreasonableness of the original shaping theory of the transition segment, proposed the circular section theory of the transition segment of the pipe belt conveyor, and provided the shaping diagram of the transition segment of the pipe belt conveyor using computer simulation [17, 18]. Based on the differential elements shaping theory, Professor Houhua Yang analyzed the mechanical behaviors of the adhesive tape in the transition segment of the pipe using a computer simulation technology, and the geometric distribution of mechanical behaviors was obtained through simulating the mechanical behaviors of the target under the influence of complex forces [19].

However, many of the above studies were just focused on the no-load conveying of the pipe belt conveyor, but the conveying of raw coal and other materials was not taken into account. In this paper, a pressure testing device for the hexagonal adjustable idlers was proposed to solve the difficulty in measuring the nonuniformly distributed pressure generated by the pipe belt conveyor when conveying raw coals. Moreover, a mechanical model of the bottom-type idlers of the pipe belt conveyor was established. Then, the sensitivity analysis on the factors influencing the pressure of the idlers was completed to reduce the workload of the mechanical analysis of the idlers. The main control factors were then found based on the weighting to be the pipe diameter and the filling rate. Finally, the conclusions of the theoretical analysis were verified through a series of simulations and tests.

2. Pressure Analysis of Idlers of Pipe Belt Conveyor

The 16.7 km pipe belt conveyor developed by the project team in 2019 has been successfully applied, as shown in Figure 1.

2.1. Analysis of Total Pressure of Idlers

As shown in Figure 2, θ is the deflection angle of materials, α is the angle related to the material filling rate, and β is the repose angle of materials.

The conveyor belt’s total pressure F_i (i = 1, 2, … , 6) applied on the idler is

It can be concluded from the aforementioned equations that idlers of the pipe belt conveyor are subject to three forces, including belt lateral pressure F_li(i = 1, 2, … , 6), belt circling force F_ci(i = 1, 2, … , 6), and belt gravity force F_gi(i = 1, 2, … , 6) [20].

As can be seen in equations (1)–(6), variables related to the force of idlers are density of material transportation ρ, material filling height h, distance between idlers L, pipe radius R, elastic modulus of the conveyor belt E_b, width of the conveyor belt B, etc. The sensitivity analysis is needed to select a design variable having the greatest effect on the pressure of idlers from optimizable variables; i.e., when the variable changes slightly, the changes of the pressure of the idler groups are regarded as sensitivity [21, 22].

3. Determination of Pressure Optimization Variables of Idlers of Pipe Belt Conveyor

3.1. Sensitivity Analysis Model

In engineering design, design sensitivity is often defined as the derivative of structural response obtained by design calculation with respect to a design variable. That is, a structural response represents structural response function F(X)’s sensitivity to design variable x_i at a specified design point x_i:where reflects structural response function F(X)’s monotonicity to design variable x_i. The absolute value of reflects structural response function F(X)’s sensitivity to design variable x_i; the greater this value is, the more sensitive to x_i the function F(X) is. The precondition of equation (7) is that the modification of x_i must be very small. However, in practical application, difficulties in changing different design variables by same values vary, while difficulties in changing optimization variables by same percentages are basically the same. For example, when the material density is large and the pipe diameter is small, changing the material density by 0.1 is easier than changing the pipe diameter by 0.1. Therefore, this paper proposes the concept of pressure weight of idlers and takes this weight as the basis for optimizing parameters.

3.2. Weight Concept

For any multivariate differentiable function, the following equation can be derived using Taylor’s expansion:where H is a higher-order term.

The partial derivative term in equation (8) is function variable’s sensitivity to function. When the higher-order term is ignored, the multivariate function can be approximated as

After the weight vector λ = (λ₁, λ₂, … , λ_n)^T is defined to make it become the percentage of function value corresponding to any one variable to total function value, the weight can be expressed as

In optimization design, the pressure of idlers is usually the implicit function of various optimization design variables and can be expanded according to equation (10), where the partial derivative term is the sensitivity of pressure of idlers and the weight vector represents the “contribution” ratio of all variables to pressure of idlers. The larger the weight of the optimization variable is, the greater effect on idlers the variable has.

As can be seen in Figure 3, when the sensitivity is used as the basis of selection, the material density and belt width have a high sensitivity and the remaining parameters are small; when the weight is used as the basis of selection, the pipe diameter and material filling height have a great effect on the pressure of idlers. Obviously, the latter matches the actual situation better. Positive weights indicate that the pressure of idlers increases with the increase of the parameter, and negative weights indicate that the pressure of idlers increases with the decrease of the parameter.

(a)

(b)

The analysis results show that the variable that has a great effect on the pressure of idlers is pipe diameter and material filling height. Therefore, final optimization variables are determined to be pipe diameter and material filling height (filling rate).

4. Simulation and Experimental Verification

4.1. Discrete Element Simulation Analysis

The difficulty of separation of raw coal and mixed gangue after mining is increased due to the nonuniform particle size. Therefore, it is necessary to crush a large amount of raw coal and gangue before transportation by the pipe belt conveyor. In general, a jaw crusher can be used to crush large coal gangue to 18–48 mm [20]. Therefore, the simulation coal radius is 20 mm, and the conveyor belt model adopts the moving-plane model to simulate the uniform linear movement of the conveyor belt. In this paper, the recovery coefficient and static friction coefficient between coal and conveyor belt are set up with reference to document [22] the simulation process as shown in Figure 4.

Tables 1 and 2 are the pressure values of different measuring areas with filling rates of 60% and 75%.

4.2. Test Design

This test was set up on a self-designed hexagon pressure testing device with adjustable pipe diameter, which consists of 6 linear feed guides, 6 pressure sensors, 1 external eight-way signal transformer, and 1 eight-way paperless recorder, as shown in Figure 5. The relevant parameters are as follows: the adjustable range of pipe diameter is 150 mm∼250 mm, the feeding of linear feed guides is 150 mm, and the support bracket is made of aluminum alloy with density of 2.66 × 10³ kg/m³ and thickness of 4 mm.

During the test, signals of 6 pressure sensors were detected within 150 mm∼250 mm of pipe diameter at no load, 60% or 75% filling rate, and full load. Then, the pressure sensor’s signals under different pipe diameters were obtained with the paperless recorder and computer, and the relevant data were processed with signal processing software [21]. The test principle and plan are shown in Figure 6.

4.3. Test Results and Discussion

Six pressure sensors’ signals at no load, 60% or 75% filling rate, and full load were researched and analyzed by processing the test data with MATLAB numerical analysis software, as shown in Figure 7.

(a)

(b)

(c)

(d)

Figures 7(a)–7(d) give the test results obtained at no load, 60% filling rate, 75% filling rate, and full load by simulating the arrangement of hexagon idlers on 6 pressure sensors. As can be seen from Figures 7(a)–7(d), No. 1 and 6 are subject to the largest pressure and unequal forces; No. 2 and 5 are subject to a large pressure and unequal forces; No. 3 and 4 are subject to the smallest pressure and unequal forces; the whole force increases with the increase of pipe diameter although each idler has different force trends. It can be known from the comparison of Figures 7(a)–7(d) that when the filling rate and pipe diameter gradually increase, idlers’ force simulated by pressure sensors increases as a whole, but the force distribution of each idler in idlers varies, which are consistent with the actual situation.

The pipe diameter is set at 150 mm. Table 3 is the comparison data table between the simulation value and the test value when the filling rate is 60% and 75%, respectively.

From Table 3, we can see that the simulation value of the idler group is close to the test value, and the average error is only 7.3%. From Figure 8, it can be concluded that the theoretical and simulated values of the pressure of the idler group are in good agreement with the experimental values, and the values are close to each other. The main sources of errors in test results, theory, and simulation analysis are neglecting the length of the overlapping area after the conveyor belt of the pipe belt conveyor becomes circular and the bending rigidity of the conveyor belt.

5. Conclusions

In this paper, a pressure testing device for the hexagonal adjustable idlers was proposed to solve the difficulty in measuring the nonuniformly distributed pressure generated by the pipe belt conveyor when conveying raw coals. Moreover, a mechanical model of the bottom-type idlers of the pipe belt conveyor was established. Then, the sensitivity analysis on the factors influencing the pressure of the idlers was completed to reduce the workload of the mechanical analysis of the idlers. The main control factors were then found based on the weighting to be the pipe diameter and the filling rate. Finally, the conclusions of the theoretical analysis were verified through a series of simulations and tests. The specific conclusions are as follows.(1)The mechanical model of the pinch-bottom idler group of the circular pipe belt conveyor is established by using the microelement method. In order to reduce the workload of mechanical analysis of the idler group, the sensitivity analysis of mechanical model of the idler group is carried out, and the pipe diameter and filling rate are obtained as the main controlling factors of the pressure of the idler group.(2)Self-designed test is used to simulate the stress of the hexagonal roller group, and the force distribution of the hexagonal roller group and the dynamic force diagram of the hexagonal roller group under different filling rates are obtained. Comparing the force simulation value with the test value of the hexagonal roller set shows that the average error between them is only 7.3%. The research provides theoretical reference and experimental basis for the design of raw coal conveying of the circular pipe belt conveyor.

Data Availability

The data used to support the findings of this study are available from the corresponding author upon request.

Conflicts of Interest

The authors declare that there are no conflicts of interests regarding the publication of this paper.

Authors’ Contributions

Shuang WANG conceptualized the study; Shuang WANG and Deyong LI formally analyzed the results; Shuang WANG and Kun HU obtained the funding; Deyong LI wrote the original draft.

Acknowledgments

This research work was supported by the National Natural Science Fund Project of China (grant no. 51874004), Nature Science Research Project of Anhui Province (grant no. 1908085QE227), and Graduate innovation fund of Anhui University of Science and Technology (grant nos. QN 2018101 and QN 2018116).

References

J.-B. Sheu and Y. J. Chen, “Transportation and economies of scale in recycling low-value materials,” Transportation Research Part B: Methodological, vol. 65, pp. 65–76, 2014.
View at: Publisher Site | Google Scholar
M. R. Phate and V. H. Tatwawadi, “Mathematical models of material removal rate & power consumption for dry turning of ferrous material using dimensional analysis in Indian prospective,” Jordan Journal of Mechanical and Industrial Engineering, vol. 9, no. 1, pp. 27–38, 2015.
View at: Google Scholar
A. Ullmann and A. Dayan, “Exhaust volume model for dust emission control of belt conveyor transfer points,” Powder Technology, vol. 96, no. 2, pp. 139–147, 1998.
View at: Publisher Site | Google Scholar
F. Zeng, Q. Wu, X. Chu, and Z. Yue, “Measurement of bulk material flow based on laser scanning technology for the energy efficiency improvement of belt conveyors,” Measurement, vol. 75, pp. 230–243, 2015.
View at: Publisher Site | Google Scholar
M. H. A. Elnaggar, “The optimization of thickness and permeability of wick structure with different working fluids of L-shape heat pipe for electronic cooling,” Jordan Journal of Mechanical and Industrial Engineering, vol. 8, no. 3, pp. 119–125, 2014.
View at: Google Scholar
M. Barburski, “Analysis of the pipe conveyor belt pressure on the rollers on its circuit,” Journal of Industrial Textiles, vol. 45, no. 6, pp. 1–16, 2015.
View at: Publisher Site | Google Scholar
M. Andrejiova, A. Grincova, D. Marasova, G. Fedorko, and V. Molnar, “Using logistic regression in tracing the significance of rubber–textile conveyor belt damage,” Wear, vol. 318, no. 1-2, pp. 145–152, 2014.
View at: Publisher Site | Google Scholar
M. M. Montazer-Rahmati and B. Amini-Horri, “From laboratory experiments to design of a conveyor-belt dryer via mathematical modeling,” Drying Technology, vol. 23, no. 12, pp. 2389–2420, 2005.
View at: Publisher Site | Google Scholar
M. E. Zamiralova and G. Lodewijks, “Measurement of a pipe belt conveyor contact forces and cross section deformation by means of the six-point pipe belt stiffness testing device,” Measurement, vol. 70, pp. 232–246, 2015.
View at: Publisher Site | Google Scholar
M. E. Zamiralova and G. Lodewijks, “Pipe conveyor test rigs: design, application and test results—part C,” Bulk Solids Handling, vol. 35, no. 1, pp. 42–49, 2015.
View at: Google Scholar
G. Fedorko, V. Molnár, J. Živčák, M. Dovica, and N. Husáková, “Failure analysis of textile rubber conveyor belt damaged by dynamic wear,” Engineering Failure Analysis, vol. 28, pp. 103–114, 2013.
View at: Publisher Site | Google Scholar
G. Fedorko, V. Molnar, M. Dovica, T. Toth, and M. Kopas, “Analysis of pipe conveyor belt damaged by thermal wear,” Engineering Failure Analysis, vol. 45, no. 1, pp. 41–48, 2014.
View at: Publisher Site | Google Scholar
V. Molnár, G. Fedorko, B. Stehlíková, P. Michalik, and M. Weiszer, “A regression model for prediction of pipe conveyor belt contact forces on idler rolls,” Measurement, vol. 46, no. 10, pp. 3910–3917, 2013.
View at: Publisher Site | Google Scholar
V. Molnár, G. Fedorko, B. Stehlíková, L’. Kudelás, and N. Husáková, “Statistical approach for evaluation of pipe conveyor’s belt contact forces on guide idlers,” Measurement, vol. 46, no. 9, pp. 3127–3135, 2013.
View at: Publisher Site | Google Scholar
G. Lodewijks, “Determination of rolling resistance of belt conveyors using rubber data: fact or fiction,” Bulk Solids Handling, vol. 23, no. 6, pp. 384–391, 2003.
View at: Google Scholar
G. Lodewijks, K. F. Drenth, and P. S. van der Mel, “The rotation of pipe conveyors,” in Proceedings of the Powder & Bulk Solids India, pp. 1–13, Mumbai, India, 2010.
View at: Google Scholar
W.-G. Song, G.-W. Zhang, and Y.-S. Deng, “Computer simulation and design of transition section of circular belt conveyor,” Journal of Northeast University (Natural Science Edition), vol. 24, no. 7, pp. 692–695, 2003.
View at: Google Scholar
W.-G. Song, H.-L. Cheng, Y.-S. Deng et al., “Shaping design of transition on pipe belt conveyor,” Hoisting and Conveying Machinery, vol. 8, pp. 7–10, 2000.
View at: Google Scholar
H.-H. Yang and T. Han, “Analysis of mechanical characteristics of belt in transition section of circular tube belt conveyor,” Mining Machinery, vol. 3, pp. 66-67, 2006.
View at: Google Scholar
Y.-C. Guo, S. Wang, K. Hu, and D.-Y. Li, “Optimizing the pipe diameter of the pipe belt conveyor based on discrete element method,” 3D Research, vol. 7, no. 1, pp. 1–9, 2016.
View at: Publisher Site | Google Scholar
Y.-C. Guo, S. Wang, K. Hu, and D.-Y. Li, “Optimization and experimental study of transport section lateral pressure of pipe belt conveyor,” Advanced Powder Technology, vol. 27, no. 4, pp. 1318–1324, 2016.
View at: Publisher Site | Google Scholar
J. Justice, C. Bower, M. Meitl, M. B. Mooney, M. A. Gubbins, and B. Corbett, “Wafer-scale integration of group III–V lasers on silicon using transfer printing of epitaxial layers,” Nature Photonics, vol. 6, no. 9, pp. 610–614, 2012.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2019 Shuang Wang et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

1477

Downloads

914

Citations