Study on the Pressure Characteristics of Shock Wave Propagating across Multilayer Structures during Underwater Explosion

Meng, Zi-Fei; Cao, Xue-Yan; Ming, Fu-Ren; Zhang, A-Man; Wang, Bin

doi:https://doi.org/10.1155/2019/9026214

Shock and Vibration

On this page

Abstract Introduction Results and Discussion Conclusions Data Availability Conflicts of Interest Acknowledgments References Copyright Related Articles

Research Article | Open Access

Volume 2019 | Article ID 9026214 | https://doi.org/10.1155/2019/9026214

Study on the Pressure Characteristics of Shock Wave Propagating across Multilayer Structures during Underwater Explosion

Zi-Fei Meng,¹Xue-Yan Cao,¹Fu-Ren Ming,¹A-Man Zhang,¹and Bin Wang²

Academic Editor: M. I. Herreros

Received29 Jul 2018

Revised08 Nov 2018

Accepted21 Nov 2018

Published13 Jan 2019

Abstract

The propagation of the shock wave across multilayer structures during underwater explosion is a very complex physical phenomenon, involving violent fluid-structure interaction (FSI) problems. In this paper, the coupled Eulerian–Lagrangian (CEL) method in AUTODYN is used to simulate the process of shock wave propagation and solve FSI problems. Firstly, the governing equation and the treatment of fluid and structure interface of the CEL method are briefly reviewed. Afterwards, two underwater explosion numerical models are established, and the results are compared with the empirical formula and experimental data, respectively, to verify the reliability of numerical solutions. The results obtained by this method show good agreements with those of the empirical formula and experiment. Furthermore, the model of the multilayer structures composed of two hemispherical shells and the fluid filled between the shells subjected to underwater explosion is established, and the pressure characteristics of the shock wave propagating across the multilayer structures are analyzed regarding the wave reflection and transmission. Finally, the effects of the shell thickness and the filled fluid type among the multilayer structures on the wave reflection and transmission are studied.

1. Introduction

The shock wave produced by underwater explosion can cause serious damage to submarines and threaten survivability of submarines [1]. Therefore, knowledge on the pressure characteristics of shock waves is of particular importance to an overall understanding of the shock resistance of submarines. Although numerous studies have been conducted [2–5], there are still many tough problems to solve due to the violent interactions between the structure and the shock wave, especially for the understanding of the wave propagation in multilayer structures. Among them, the double-layer hemispherical shell is often used as the protective structure of submarines and other underwater vehicles. Hence, in this paper, the pressure propagation characteristics of the underwater explosion shock wave in two hemispherical shells with air or water among them are investigated.

Regarding shock wave propagation in structures, a great deal of researches have been performed. Taylor [6] assumed that the underwater explosion shock wave is a one-dimensional planar, exponentially decaying pressure wave and adopted this planar wave as shock load to calculate the pressure and impulse on the wetted surface (the interface of water and structure). Although Taylor’s solution can give accurate pressure time histories for a simple plate, it is difficult to capture the reflected wave from the multilayer structures. On this basis, Jin et al. [7] presented an analytical method to obtain interfacial pressure of coated plates under underwater weak shock waves. The method can take into account multiple reflections and transmissions in multilayer structures. But the major limitation to this method is that the shock wave should be weak enough to guarantee some assumptions they adopted that rigid body motion is negligible and the variation of the wave propagation time in each medium caused by the medium deformation is negligible. Recently, Chen et al. [8] applied one-dimensional cavitation theory and section-varying bar theory to discuss the propagation characteristics of stress waves in simple plates and stiffened plates (T profiles and I profiles). Considering the cavitation effect, the pressure and impulse on the wetted surface are predicted accurately by analytical solution. They found that obviously pressure drops and oscillations occur on the wetted surface in the stiffened plates model due to the superposition of the reflected wave from the structure and the incident wave compared to the simple plate model. However, this analytical model is limited to the one-dimensional system.

Valuable researches on pressure characteristics of the shock wave in structures using numerical simulation have also been conducted. Otsuka et al. [9] utilized LS-DYNA3D, an analysis code using the arbitrary Lagrangian–Eulerian approach, to simulate the propagation process of the explosion shock waves produced by the two modes of detonation (a detonation cord and an emulsion explosive) in the three layers of air, water, and structure. They found that as the air layer becomes thick, the peak pressure decreases in the water. However, the impulse remains unchanged since the duration of pressure is increased by the effect of a reflected wave. Yet, their simulation lacks a comparative study between the different material layers. Desceliers et al. [10] presented a new numerical hybrid method dedicated to the simulation of the transient elastic wave propagation in multilayer unbounded media, which can be fluid or solid, subjected to given transient loads. This method can capture clearly some profiles of the elastic waves including reflected waves, transmitted waves, and refracted surface waves. However, it is restricted to simple geometrical structures. Wang et al. [11] used the coupled Eulerian–Lagrangian (CEL) method in AUTODYN to investigate the shock wave propagation characteristics near the air-backed plate and water-backed plate. They found that two pressure peaks occurred in these two numerical models, where the first peak is generated by the incident wave and the second peak is induced by the reflected wave from the plate due to the impedance of the water being lower than that of the plate. But in that work, they did not apply the CEL method to multilayer structures. Wu et al. [12] investigated the protection effects of a mitigation layer on the structure exerted by an underwater explosion with the help of the Mie-Grneisen mixture model and discussed the affections of the layer material (steel, neoprene, and polyethylene), layer thickness, and explosive-structure distance on protection effects. They concluded that the acoustic impedance of the mitigation layer plays an important role in determining not only the property of shock loads but also the occurrence of protection effects of the mitigation layer, while the layer thickness and explosive-structure distance have a little effect on the main shock loads. Nevertheless, the loads of the inner shock wave in the mitigation layer are their main concern. In addition, other scholars mainly focus on structural response and damage characteristics [13–21]. In a word, theoretical research based on certain assumptions is suitable for a structure with a simple geometry, while numerical simulation is easier to implement to deal with shock wave propagation problems in complex structures.

Owing to the presence of complex superposition of multiple waves, geometry with curvature, moving interface, and large plastic deformation, traditional theoretical research comes across many difficulties in solving shock wave propagation characteristics in multilayer structures. In order to tackle these problems, the CEL method in AUTODYN is adopted to study the propagation characteristics of the shock wave in the multilayer structures during underwater explosion in the present work. The shell thickness and the filled medium between the double shells are focused, and their influences on the propagation of the shock wave are analyzed. The relationships among the incident, the reflected, and the transmitted shock waves are discussed.

2. Theoretical Background

2.1. Coupled Eulerian and Lagrangian Method

Actually, the process of underwater explosion near structures is a complicated fluid-structure interaction (FSI) problem [22, 23]. Two sorts of methods are usually used to solve this problem, namely, the Lagrangian method and Eulerian method [11, 24]. Both of them have their own advantages and limitations. The Lagrangian method is suitable for describing the stress, strain, and deformation of the structure. However, when encountering large deformation problems, the Lagrangian mesh is severely distorted, which leads to adverse effects on calculation. Conversely, the Eulerian method can deal with large deformation problems and some flow problems. But, it cannot track accurately material interfaces. Therefore, a coupled Eulerian–Lagrangian (CEL) analysis method which combines the advantages of these two methods is introduced to tackle FSI problems. The structure part is solved by the Lagrangian method, while the fluid part is solved by the Eulerian method. The FSI between the two parts is carried out at the interface [11, 25]. This approach has been made possible in some hydrocodes, e.g., AUTODYN [25] and ABAQUS [26]. Specifically, in the Lagrangian method based on the finite difference scheme, the material is attached to the mesh element which deforms with the flow of the material, and the mass of the element remains constant [25]. In the Lagrangian solver, given the node position , the node velocity , the element density , the element volume , the internal energy , and the governing equations are as follows [25, 27, 28]:where , , , and are the initial density, initial volume, mass, and total stress tensor, respectively. The stress tensor is separated into a hydrostatic component and a deviatoric component, which can be referred from the study in [29].

A series of calculations in a Lagrangian subgrid are shown schematically in Figure 1 (the left column). A detailed description about this process can be referred from the study in [25, 30–32].

In the Eulerian solver, assuming that the fluid is inviscid, the explosion process is adiabatic and the body force is neglected [27, 28, 33, 34]. The governing equations can be written as follows [35, 36]:where is the density, is the velocity, is the total energy, is the pressure, is the mass flux, is the momentum flux, and is the energy flux.

In fact, the Eulerian method contains two steps to account for both the changes in the element solution caused by the source and the transport of the material through the mesh. More details can be found in [32, 37–39].

Besides, the calculation process of the Eulerian solver is shown in Figure 1 (the right column). There are also many complicated works that need to be accomplished including the calculation of intersection points, intersecting lines, common areas, surface area, and three-dimensional volume. These detail descriptions can be found in [40–43].

2.2. Treatments of Fluid-Structure Interface

The interaction between the structure and fluid is performed at the coupling surface. At the interface, the structure described by the Lagrangian view is regarded as the geometric and velocity boundary for the fluid. Conversely, the fluid is regarded as the pressure boundary for the structure [25, 32, 37].

For the Lagrangian structure element, the position , velocity , force , and mass are defined at the node, while the stress , strain , pressure , energy , and density are defined at the center of the element. For the Eulerian fluid element, all variables are defined at the center of the element except the position (Figures 2(a) and 2(b)). This definition mode facilitates the coupling between the Lagrangian structure and the Eulerian fluid [25].

(a)

(b)

(c)

Figure 2

(a) Lagrangian elements: x, u, F, and m in the node and σ, ε, P, e, and ρ in the element center; (b) Eulerian elements: x in the node and other variables in the element center; (c) fluid-structure interaction interface: Euler as the pressure condition for Lagrange and Lagrange as the velocity condition for Euler. Blue represents the material in the Eulerian element [25, 32, 37]. σ, ε, P, e, ρ, x, u, F, and m are the stress, strain, pressure, energy, density, coordinate, velocity, force, and mass, respectively.

2.3. Numerical Validation

Firstly, the free-field underwater explosion model is established to validate the feasibility of the CEL method in AUTODYN [25] for simulating the shock wave pressure. The spherical TNT charge with a mass m_r of and a radius R₀ of is detonated in the cylindrical domain with a radius of and a height of , as shown in Figure 3(a). A nondimensional distance hereinafter is defined to describe the distance from the measuring points to the TNT center, namely, , where is the detonation distance. Different distances of are chosen. The transmitting boundary condition is set around the computational domain to reduce the nonphysical reflection. In the present work, we adopt a two-dimensional axisymmetric model to simulate the process of free-field underwater explosion.

(a)

(b)

(c)

The density of TNT is 1,630 , and the detonation velocity is 6,930 m/s. Besides, the state equation of Jones–Wilkins–Lee (JWL) hereinafter is used to simulate the TNT detonation process, and it can be written as equation (3), where is the pressure produced by the explosive charges, is the specific volume of detonation products over the specific volume of undetonated explosives, is the specific internal energy, and , , , , and are material constants listed in Table 1 [25, 44]. The equation of state for water hereinafter can be defined as equation (4), where , in which is the initial density of water, i.e., . The term is the specific internal energy for water. , , , , , , and are constants defined in the AUTODYN material library. These parameters are listed in Table 2 [25, 44]:

The water and explosive are modeled by the Eulerian subgrid. In order to test the convergence of the present CEL method, three mesh resolutions are used in the Eulerian part, 2.5 mm, 5 mm, and 10 mm, respectively. An evenly partitioned grid is used. The shock wave pressure versus time at is measured, as shown in Figure 4. Clearly, the result of the mesh size 2.5 mm shows a little difference compared with the result of the mesh size 5 mm. The convergence rate of three resolutions is calculated to be 1.95 using their peak pressure. Generally, if the convergence rate is over 1, then it means this numerical method can give better results [45]. In order to reduce the computational cost, the element size for this free-field underwater explosion model is 5 mm, and the number of elements is about 100,000.

The attenuation of shock wave pressure varying with time is given by the Zamyshlyayev empirical formula [3]:where is the peak pressure of the shock wave (Pa), is the time decay constant of the shock wave (s), is the weight of the explosive charge (kg), is the distance between the explosion center and measuring point (m), is the initial radius of the explosive (m), is the time when the bubble reaches its maximum radius (s), is the hydrostatic pressure near the explosion center (Pa), is the atmospheric pressure (Pa), is the sound speed of water (m/s), and is the initial depth of the explosion center (m).

The numerical model of free-field underwater explosion and the pressure contours at two typical instants are shown in Figure 3. The shock wave propagating in water is spherical (Figure 3(b)). When the shock wave arrives at the boundary, it is not reflected due to the enforcement of the transmitting boundary condition, as shown in Figure 3(c). The time histories of the pressure at and obtained from CEL and Zamyshlyayev empirical formulas [3] are compared in Figure 5. It reveals that they accord with each other. If one defines the relative error of the peak pressure between the numerical and the Zamyshlyayev results as , the values can be listed in Table 3. We can find that the relative errors are within 10%. Although there are some oscillations caused by the strong discontinuity of the shock wave in the numerical results, the whole attenuation process and peak pressure values are in good agreement with the empirical formula.

(a)

(b)

In fact, during the shock wave propagating in multilayer media, the FSI process is involved. In order to further test the reliability of the CEL method in dealing with FSI problems, an experiment (this experimental case and relevant data are provided by the Institute of Fluid Physics, China Academy of Engineering Physics) is performed in a water tank with the size of 2 m × 2 m × 2 m. The depth of water is 1.6 m. As shown in Figure 6, the square test plate made from the mild steel Q235 is fixed on the wall of the tank. It has a length of 0.8 m and a thickness of 0.003 m. The cylindrical charge has a size of Φ 20 mm × 18 mm, and thus, the mass is 10 g. The charge is placed in the water, and its depth is = 0.8 m. The axis of the charge is parallel with the plate, and the distance from the axis to the plate is about four times the charge radius , namely, . The experimental layout is illustrated in Figure 6. Two measuring points ( and ) are placed on the side of the plate to record the displacement and velocity (Figure 7).

The three-dimensional numerical model is established according to the layout of the experiment. The water and TNT are also modeled by the Eulerian subgrid. Note that the air in this numerical model can be ignored. The steel is modeled by the Lagrangian subgrid, and its density is 7,830 . The Johnson–Cook strength and fracture parameters for the steel are listed in Tables 4 and 5 (found in [46]). The smallest element size of the Eulerian mesh is 5 mm, and it is 1.5 mm for the Lagrangian mesh. The Euler domain consists of about 3.8 million cells, and the Lagrangian domain contains 570,000 cells.

The displacement and velocity time histories calculated by the CEL method are compared with the experimental results in Figure 8. It is not hard to see from Figure 8 that they are in good accordance, especially the displacement time histories. Therefore, the CEL method can simulate the FSI process well, and it can predict accurately the shock wave propagation in the complex model.

(a)

(b)

(c)

(d)

3. Results and Discussion

3.1. Numerical Model

The two-dimensional axisymmetric numerical model of a double-layer hemispherical shell subjected to underwater explosion is established to investigate the propagation characteristics of the shock wave in multilayer media, as plotted in Figure 9. The outer shell has a radius of and a thickness of , while the inner shell has a radius of and a thickness of . The parameters related to distance are normalized by the charge radius , namely, , , , , and . The thickness of the outer shell is changed to test the effects, so are selected with a constant of . The mass of the spherical TNT charge, the charge radius , and the size of the Eulerian domain are the same as those of the free-field model in Section 2.3. The measuring points 1 and 3 are located near the outside surface of the outer shell and the inner shell, respectively. The measuring point 2 is located near the inside of the outer shell, and the distance from point 2 to the outer shell is . The shell structure is fixed around the boundary, and the transmitting condition is enforced around the fluid domain so as to overcome the nonphysical reflection. The parameters related to time hereinafter are normalized by the time decay constant θ when in equation (8).

(a)

(b)

Medium 1 and medium 2 are water or air. The material parameters of water and charge are the same as those in the free-field model. Air is modeled by the ideal gas equation of state, which can be written as , where the specific heat ratio is 1.4, the initial density of air is 1.225 , and the specific energy is 253.4 [25]. The density of steel is 7,830 [25]. Note that the Johnson–Cook strength parameters listed in Table 6 [25] for the steel are different from those of the experiment in Section 2.3. The element size for the Eulerian part is also 5 mm, the same as that of the free-field model, and more than four elements in the thickness direction are discretized for the Lagrangian part. Thus, the Eulerian domain contains about 100,000 cells, and the number of Lagrangian cells ranges from 4,230 to 8,940 due to different outer shell thicknesses.

3.2. Shock Wave Propagation Process

Figure 10 shows the shock wave propagation process for the case of media 1 and 2 filled with water and air, respectively, at the detonation distance . Several typical instants during the process are presented. Obviously, they show a similar process after the charge detonation, and a spherical shock wave propagates to the outer shell surface (Figure 10(a)); when the wave arrives at the outer shell whose other side is backed to water, it is reflected and transmitted by the shell, as plotted in Figure 10(b) (the left column). Accordingly, when the wave arrives at the outer shell whose other side is backed to air, there exists a rarefaction wave reflected which travels backwards in water. Due to the much lower impedance of the air, the transmitted wave is weaker than the reflected wave. Therefore, Figure 10(b) (the right column) cannot recognize the transmitted wave in the air-backed case; when the transmitted shock wave reaches the inner shell whose other side is backed to water, the shock wave is reflected and transmitted over the shell again in Figure 10(c) (the left column). Cavitation occurs near the outer shell in the air-backed case, as shown in Figure 10(c) (the right column). Also, the pressure of the reflected and transmitted waves on the inner shell in the water-backed case is obviously larger than that in the air-backed case. Later, the wave reflected from the inner shell propagates to the outer shell, and then it is reflected and transmitted again. Due to the complex superposition of the incident wave, the reflected wave, and the transmitted wave, the pressure becomes very complicated (Figure 10(d) (the left column)). At the same time, the cavitation region in the air-backed case is further expanding.

(a)

(b)

(c)

(d)

On the whole, because of the severe mismatch of the impedance between different media, the intensity of the transmitted wave of the shells backed to water is larger than that of the shells backed to air and the cavitation region near the outer shell occurs in the air-backed case.

3.3. Shock Wave Reflection

Figure 11 shows the time history of the shock wave pressure at point 1. The outer shell is backed to water in case a and to air in case b. Meanwhile, different thicknesses of the outer shell are also taken into account, and the detonation distance is 10. Note that medium 2 behind the inner shell has a little effect on the reflected pressure near the outer shell. As the results show, if , with the increase of the outer shell thickness, the pressure of the reflected wave tends to be steady in both cases. By comparing the above two cases, it can be seen that the peak pressure of the reflected wave caused by the water-backed shell is larger than that of the air-backed case, but the latter tends to be consistent with the former in value if . What is more, the pressure fluctuates more violently for the air-backed case.

(a)

(b)

This can be explained from the perspective of wave propagations. The first interface for the wave arrival is the same for the two cases, namely, the interface between the water and the outside of the outer shell. Therefore, the reflected wave pressure at this interface should be equal in both cases. However, at the next interface, the shock wave transmits from the inside of the outer shell to the water in case a while from the inside to the air in case b. Because the acoustic impedances of water and air are much lower than that of steel, there is a rarefaction wave reflected at this interface [47–51]. Therefore, the intensity of the incident shock wave is unloaded. Moreover, the acoustic impedance of air is lower than that of water, the unloading effect in case a is less serious than that in case b, so the peak pressure of the reflected wave in case a is larger than that in case b. The stiffness of the outer shell, however, is improved with the increase of shell thickness. Hence, the intensity of the reflected wave in these two cases is gradually enhanced. To sum up, if the outer shell thickness , the medium behind the outer shell will affect the peak pressure of the reflected wave slightly.

The reflection coefficient of shock wave pressure is defined as , where is the peak pressure of the reflected wave at point 1 and is the peak pressure at the same distance in the free-field underwater explosion model. In the present work, if the detonation distance is far enough, the numerical model can be regarded as a one-dimensional model. Based on Taylor’s assumptions [6], we can obtain , where is the pressure of the reflected wave and is the pressure of the rarefaction wave produced by the motion of the structure. is the density of water, is the sound speed of water, and is the velocity of the outer shell. If the perfect reflection of the incident wave occurs [52, 53], the pressure of the reflected wave would read . Therefore, should satisfy theoretically. And then, the reflection coefficient holds .

Figure 12 illustrates the reflection coefficients of the shock wave varying with the thickness of the outer shell at the distance . Obviously, the reflection coefficients increase with the increase of shell thickness, but the trend gradually slows down for the two cases. Moreover, the coefficients of the air-backed case are almost the same as those of the water-backed case if . The reflection coefficients exceed 1 no matter what the medium is filled with at the back of the outer shell. It means that the presence of the outer shell enhances the peak pressure at point 1.

If the thickness , the shock wave reflection coefficients varying with the distance in these two cases are plotted in Figure 13. The coefficients decrease with the increase of detonation distance, as shown in Figure 13. The relationship between the reflection coefficients and the detonation distance is approximately linear for these two cases. In the present work, we can recast the Zamyshlyayev empirical formula, i.e., equation (6), as , where and are the ratio parameter and exponent parameter, respectively. So, a relation between the reflection coefficient and the distance can be obtained as . As described in the literature [54], the rarefaction wave (i.e., ) can be neglected at the early stage of shock wave impinging on the absolutely rigid structure. For the elastic shell, if we extract the velocities of the outer shell near point 1 from numerical results, listed in Table 7, we can find these velocities are positive for these cases. So, the rarefaction wave cannot be neglected. In this case, the reflection coefficient of peak pressure varying with the distance can be obtained from the numerical simulation, as shown in Figure 13. One should notice that the decreasing trend of the coefficient is only suitable for the cases of close distances (i.e., ).

The impulse reflection coefficient can be defined as , where is the pressure impulse at point 1 and is the pressure impulse at the same distance in the free-field underwater explosion model. Figure 14 shows the impulse reflection coefficients varying with shell thickness in the water-backed case and air-backed case at the detonation distance . The impulse reflection coefficients increase with the increase of shell thickness, and the tendency becomes gradually slow. If , the impulse reflection coefficients of the air-backed case will be smaller than those of the water-backed case because the deformation of the outer shell in the air-backed case is more serious than that in the water-backed case. If the thickness , the coefficients of the air-backed case are larger than those of the water-backed case. Under this circumstance, the deformation of the outer shell is not the principal factor influencing impulse, since the stiffness of the outer shell is high enough. The reason for this phenomenon is that the incident wave transmits over the outer shell in the water-backed case, while the incident wave is mainly reflected in the air-backed case because of the impedance difference between water and air.

If the thickness , the impulse reflection coefficients varying with different detonation distances in these two cases are plotted in Figure 15. The coefficients approximately decrease linearly with the increase of detonation distance whatever the outer shell is exposed to water or air. It should be noticed that of the air-backed case changes faster than that of the water-backed case and varies in a wide range, which may be due to the fact that complex superposition of the wave system between the outer shell and the inner shell affects seriously the pressure of point 1 after , found in Figure 10.

3.4. Shock Wave Transmission

When the shock wave transmits over the outer shell to the inner shell, the peak pressure and the energy of the shock wave gradually attenuate. In Figure 16, the pressure histories of the transmitted shock wave for different shell thicknesses are presented. Medium 1 between the two shells and medium 2 behind the inner shell are water or air, respectively. The detonation distance is 10. In Figure 16(a), medium 1 and medium 2 are both water (noted as water-water), while medium 1 is water and medium 2 is air (noted as water-air) in Figure 16(b). Obviously, when the wave transmits over the outer shell, a peak pressure, called the transmitted peak, occurs in these two cases, and then it attenuates quickly. With the attenuation of the pressure, the waves reflected by the outer and inner surfaces of the inner shell reach point 2 at about , as shown in Figure 17. Owing to the superposition of the transmitted wave and the reflected wave, it causes the pressure to rise and generates a second peak pressure, called the reflected peak, which might have a second impact on the shell (Figures 16(a) and 16(b)). In addition, both the peaks decrease with the increase of the outer shell thickness. It is worth noting that the reflected peak can be larger than the transmitted peak if . It indicates that the reflected wave produced by the inner surface of the outer shell plays a leading role under this circumstance.

(a)

(b)

(c)

(d)

(a)

(b)

(c)

(d)

Media 1 and 2 are both air (noted as air-air) in Figure 16(c), while medium 1 is air and medium 2 is water (noted as air-water) in Figure 16(d). The peak pressures of the transmitted shock wave at point 2 are almost the same at the same shell thickness for both the cases, while they are about 1/330 times that of the water-water case. It may be due to the lower impedance of air which is about 1/5,000 times that of the water. If the shell thickness in these two cases, there are no values in pressure history curves when the time exceeds , which is due to the fact that the outer shell after deformation is over the position of the measuring point 2. With the increase of the shell thickness, the pressure attenuates gradually. Different from the water-water case or water-air case, the second peak arrives later (at about ) which may be due to the strong impedance mismatch. Also, the pressure time histories show no differences for medium 2 filled with water or air behind the inner shell.

As seen in Figures 16(a)–16(d), it can be found that medium 1 has a great influence on the pressure of the transmitted wave. On the contrary, medium 2 behind the inner shell has few effects on the transmitted pressure.

The transmission coefficient can be defined as the ratio of the peak pressure of the transmitted wave at point 2, i.e., the first peak in Figure 16, to the peak pressure of the incident shock wave in free field. The transmission coefficients of the shock wave varying with different shell thicknesses are plotted in Figure 18. As described in the analysis above, medium 2 behind the inner shell has little effect on the peak pressure of the transmitted shock wave. Therefore, the cases in which medium 2 is water while medium 1 is water or air are hereinafter taken for examples. With the increase of the shell thickness, the transmission coefficients of the shock wave decrease exponentially for the two cases. Although the peak pressure of the air-backed case is much smaller than that of the water-backed case, the trend of transmission coefficients varying with different shell thicknesses is similar to that of the water-backed case.

Taking the thickness for example, the curves of the transmission coefficients varying with different detonation distances can be plotted in Figure 19. Unlike Figure 13, with the increase of the detonation distance, the transmission coefficients have a trend of increase by degrees. The difference may be because the peak pressure is affected by the inner shell and the outer shell together, while is mainly affected by the outer shell, although the peak pressure and decrease as the detonation distance increases.

The total energy released by the TNT is 2703 kJ at , and the proportion of the energy absorbed by the outer shell accounting for the total energy is plotted in Figure 20. Because the TNT mass is quite small and the shell has not been destroyed, the energy absorbed by the outer shell is less. With the increase of shell thickness, the energy absorption proportion increases generally. Another feature is that the proportion of the energy absorbed by the outer shell can be up to 2% for the air-backed case while about 1% for the water-backed case when the shell thickness ranges from 0.1 to 0.8. For the same shell thickness, the energy absorption of the air-backed case is two to three times that of the water-backed case. This may attribute to the larger deformation of the shell in the air-backed case.

Figure 21 shows the proportion of the energy transmitted over the outer shell versus different thicknesses. The transmission energy gradually decreases with the increase of shell thickness for the two cases. For the same shell thickness, the transmission energy of the air-backed shell is much smaller than that of the water-backed shell, which coincides with the above results in Figure 18. That is, the transmission coefficient of the air-backed case is much smaller than that of the water-backed case.

Figure 22 shows the Mises stress contours of the outer and inner shells for the case of the outer shell thickness . It can be seen that if medium 1 between the two shells is air, the maximum stress of the shell will be about 1.5 times that of the water-backed shell, and there are almost no stresses in the inner shell. Therefore, it can be concluded that if the medium is filled with air between two shells, the inner shell is prevented from serious impact.

(a)

(b)

3.5. Comparison of Shock Wave Reflection and Transmission

Actually, the shock wave pressure measured on the outer surface of the shell is from the superposition of the incident shock wave and the reflected shock wave. In order to study the relationship between the reflection and transmission of the shock wave, the ratios of the peak pressure of the reflected shock wave to that of the transmitted shock wave are plotted in Figure 23. The peak pressure of the reflected shock wave is the difference between the measured pressure near the surface of the outer shell and the incident pressure in free field.

Obviously, with the increase of the thickness, no matter what the outer shell is backed to, the ratios increase and tend to be slow when the thickness exceeds to some extents for the air-backed case. The reason for this phenomenon is that the peak pressure of the transmission wave decreases drastically with the increase of shell thickness (Figures 16 and 18). Another feature is that the ratios of the shell backed to air are much larger than those of the shell backed to water. That is, the reflection proportion is dominant for the air-backed case. This can be explained by the fact which can be found in Section 3.4 that the peak pressure of the air-backed case is smaller than that of the water-backed case for two orders of magnitude.

Figure 24 shows the peak pressure ratios at the measuring points 1 and 3 versus different outer shell thicknesses. Generally, the ratios decrease with the increase of the shell thickness no matter what media 1 and 2 are filled with. It indicates the reflection proportion increase as the shell thickens. In addition, the ratios of the water-backed cases (water-water case and water-air case) are obviously larger than those of the air-backed cases (air-air case and air-water case) which almost coincide with each other. These accord well with the analysis in Sections 3.3 and 3.4.

After the directive wave propagating over the outer shell, the transmitted wave arrives at the inner shell, which can be regarded as a directive wave producing a new charge, i.e., the equivalent charge mass . That is to say, the effect of the transmitted wave on the inner shell is, to some extent, equivalent to that of a new charge on the inner shell. With the aid of the analysis in Section 3.3, can be transformed from a free-field component of incident peak pressure on the inner shell, namely, , by Zamyshlyayev empirical formula (6).

Table 8 presents the ratios of the equivalent charge mass to the actual charge mass . The cases of the medium between the two shells filled with water are considered, and air-backed cases are absent because is too small. As the table shows, the equivalent charge mass for the inner shell can be decreased about 75% if the outer shell thickness is over 0.2 times the charge radius. With the increasing thickness, the equivalent charge mass decreases sharply.

4. Conclusions

The shock wave propagation between two hemispherical shells which are filled with different media is studied based on the coupled Eulerian–Lagrangian method in AUTODYN. The relationships among the incident, reflected, and transmitted waves are discussed.

The medium between two hemispherical shells will affect the peak pressure of the reflected wave generated by the outer shell slightly if the outer shell thickness is thicker than a certain level (here, it is over 0.4 times the charge radius). The reflection coefficients of peak pressure and impulse increase with the increase of shell thickness and decrease linearly with the increase of detonation distance. Besides, the cavitation area caused by the reflected rarefaction wave near the outer shell occurs in the air-backed case.

When the wave transmits over the outer shell, a peak pressure, called the transmitted peak, occurs whatever the medium behind the outer shell is water or air. It is worth mentioning that a second peak, which is relatively compared to the transmitted peak, can be produced by the reflections of the inner shell, and it will be larger than the transmitted peak if the outer shell thickness reaches a certain extent (here, it is over 0.6 times the charge radius) for the water-water and water-air cases. The medium between the two shells has great influences on the transmitted wave, while the medium behind the inner shell has slight effects on the transmitted wave. With the increase of the shell thickness, the transmission coefficients of the shock wave decrease exponentially and increase linearly with the detonation distance whatever the outer shell is exposed to water or air.

For the same outer shell thickness, the energy absorption of the air-backed case is about two to three times that of the water-backed case. With the increasing thickness, the equivalent charge mass decreases drastically. The equivalent charge mass for the inner shell can be decreased about 75% if the outer shell thickness is over 0.2 times the charge radius.

Data Availability

All data included in this study are available upon request by contacting the corresponding author.

Conflicts of Interest

The authors declare that they have no conflicts of interest.

Acknowledgments

This paper was supported by the National Natural Science Foundation of China (51609049 and U1430236) and the Natural Science Foundation of Heilongjiang Province (QC2016061).

References

F. R. Ming, A. M. Zhang, H. Cheng, and P. N. Sun, “Numerical simulation of a damaged ship cabin flooding in transversal waves with smoothed particle hydrodynamics method,” Ocean Engineering, vol. 165, pp. 336–352, 2018.
View at: Publisher Site | Google Scholar
R. H. Cole, Underwater Explosions, Princeton University Press, Princeton, NJ, USA, 1948.
B. V. Zamyshlyaev and Y. S. Yakovlev, “Dynamic loads in underwater explosion,” Intelligence Support Center, Washington, DC, USA, 1973, Tech. Rep. AD-757183.
View at: Google Scholar
J. M. Brett, “Numerical modelling of shock wave and pressure pulse generation by underwater explosions,” DSTO Aeronautical and Maritime Research Laboratory, Canberra, Australia, 1998, Tech. Rep. AR-010-558.
View at: Google Scholar
F. R. Ming, P. N. Sun, and A. M. Zhang, “Investigation on charge parameters of underwater contact explosion based on axisymmetric sph method,” Applied Mathematics and Mechanics, vol. 35, no. 4, pp. 453–468, 2014.
View at: Publisher Site | Google Scholar
G. I. Taylor, “The pressure and impulse of submarine explosion waves on plates,” in Underwater Explosion Research, pp. 1155–1173, Office of Naval Research, Arlington, VA, USA, 1950.
View at: Google Scholar
Z. Y. Jin, C. Y. Yin, Y. Chen, X. C. Huang, and H. X. Hua, “An analytical method for the response of coated plates subjected to one-dimensional underwater weak shock wave,” Shock and Vibration, vol. 2014, no. 2, Article ID 803751, 13 pages, 2014.
View at: Google Scholar
Y. Chen, X. Yao, and W. Xiao, “Analytical models for the response of the double-bottom structure to underwater explosion based on the wave motion theory,” Shock and Vibration, vol. 2016, no. 9, Article ID 7368624, 21 pages, 2016.
View at: Publisher Site | Google Scholar
M. Otsuka, S. Tanaka, and S. Itoh, Research for Explosion of High Explosive in Complex Media, Springer Netherlands, New York City, NY, USA, 2006.
C. Desceliers, C. Soize, Q. Grimal, G. Haiat, and S. Naili, “A time-domain method to solve transient elastic wave propagation in a multilayer medium with a hybrid spectral-finite element space approximation,” Wave Motion, vol. 45, no. 4, pp. 383–399, 2008.
View at: Publisher Site | Google Scholar
G. Wang, S. Zhang, M. Yu, H. Li, and Y. Kong, “Investigation of the shock wave propagation characteristics and cavitation effects of underwater explosion near boundaries,” Applied Ocean Research, vol. 46, no. 2, pp. 40–53, 2014.
View at: Publisher Site | Google Scholar
Z. D. Wu, L. Sun, and Z. Zong, “Computational investigation of the mitigation of an underwater explosion,” Acta Mechanica, vol. 224, no. 12, pp. 3159–3175, 2013.
View at: Publisher Site | Google Scholar
L. Hammond and R. Grzebieta, “Structural response of submerged air-backed plates by experimental and numerical analyses,” Shock and Vibration, vol. 7, no. 6, pp. 333–341, 2000.
View at: Publisher Site | Google Scholar
R. Rajendran and J. M. Lee, “A comparative damage study of air- and water-backed plates subjected to non-contact underwater explosion,” International Journal of Modern Physics B, vol. 22, pp. 1311–1318, 2008.
View at: Publisher Site | Google Scholar
X. L. Yao, J. Guo, L. H. Feng, and A. M. Zhang, “Comparability research on impulsive response of double stiffened cylindrical shells subjected to underwater explosion,” International Journal of Impact Engineering, vol. 36, no. 5, pp. 754–762, 2009.
View at: Publisher Site | Google Scholar
Z. F. Zhang, F. R. Ming, and A. M. Zhang, “Damage characteristics of coated cylindrical shells subjected to underwater contact explosion,” Shock and Vibration, vol. 2014, Article ID 763607, 15 pages, 2014.
View at: Publisher Site | Google Scholar
Z. Wang, X. Liang, and G. Liu, “An Analytical Method for Evaluating the Dynamic Response of Plates Subjected to Underwater Shock Employing Mindlin Plate Theory and Laplace Transforms,” Mathematical Problems in Engineering, vol. 2013, Article ID 803609, 11 pages, 2013.
View at: Publisher Site | Google Scholar
G. Z. Liu, J. H. Liu, J. Wang, J. Q. Pan, and H. B. Mao, “A numerical method for double-plated structure completely filled with liquid subjected to underwater explosion,” Marine Structures, vol. 53, pp. 164–180, 2017.
View at: Publisher Site | Google Scholar
Z. Zhang, L. Wang, and V. V. Silberschmidt, “Damage response of steel plate to underwater explosion: effect of shaped charge liner,” International Journal of Impact Engineering, vol. 103, pp. 38–49, 2017.
View at: Publisher Site | Google Scholar
D. Su, Y. Kang, X. Wang et al., “Analysis and numerical simulation for tunnelling through coal seam assisted by water jet,” Computer Modeling in Engineering and Sciences, vol. 111, no. 5, pp. 375–393, 2016.
View at: Google Scholar
Y. S. Ferezghi, M. Sohrabi, and S. Nezhad, “Dynamic analysis of non-symmetric functionally graded (FG) cylindrical structure under shock loading by radial shape function using meshless local Petrov-Galerkin (MLPG) method with nonlinear grading patterns,” Computer Modeling in Engineering and Sciences, vol. 113, no. 4, pp. 497–520, 2017.
View at: Google Scholar
N. N. Liu, F. R. Ming, L. T. Liu, and S. F. Ren, “The dynamic behaviors of a bubble in a confined domain,” Ocean Engineering, vol. 144, pp. 175–190, 2017.
View at: Publisher Site | Google Scholar
N. N. Liu, W. B. Wu, A. M. Zhang, and Y. L. Liu, “Experimental and numerical investigation on bubble dynamics near a free surface and a circular opening of plate,” Physics of Fluids, vol. 29, no. 10, Article ID 107102, 2017.
View at: Publisher Site | Google Scholar
F. R. Ming, P. N. Sun, and A. M. Zhang, “Numerical investigation of rising bubbles bursting at a free surface through a multiphase sph model,” Meccanica, vol. 52, no. 11-12, pp. 1–20, 2017.
View at: Publisher Site | Google Scholar
Autodyn explicit software for nonlinear dynamics, Theory manual version 4.3, Century Dynamics Inc., Concord, CA, USA, 2003.
D. Simulia, Abaqus Version 2016 Documentation USA, Dassault Systems Simulia Corp, Johnston, RI, USA,, 2016.
B. G. R. Liu and M. B. Liu, Smoothed Particle Hydrodynamics: a Meshfree Particle Method, World Scientific, Singapore, 2004.
A. M. Zhang, W. S. Yang, and X. L. Yao, “Numerical simulation of underwater contact explosion,” Applied Ocean Research, vol. 34, pp. 10–20, 2012.
View at: Publisher Site | Google Scholar
G. Luttwak and M. S. Cowler, “Advanced eulerian techniques for the numerical simulation of impact and penetration using autodyn-3d,” 1999, Tech. rep.
View at: Google Scholar
D. J. Steinberg, “Spherical explosions and the equation of state of water,” Lawrence Livermore National Laboratory, Livermore, CA, USA, 1987, UCID-20974.
View at: Google Scholar
M. L. Wilkins, “Calculation of elastic-plastic flow,” Journal of Biological Chemistry, vol. 280, no. 13, pp. 12833–12839, 1969.
View at: Google Scholar
D. J. Benson, “Computational methods in Lagrangian and eulerian hydrocodes,” Computer Methods in Applied Mechanics and Engineering, vol. 99, no. 2-3, pp. 235–394, 1992.
View at: Publisher Site | Google Scholar
J. H. Kim and H. C. Shin, “Application of the ale technique for underwater explosion analysis of a submarine liquefied oxygen tank,” Ocean Engineering, vol. 35, no. 8-9, pp. 812–822, 2008.
View at: Publisher Site | Google Scholar
J. S. Peery and D. E. Carroll, “Multi-material ale methods in unstructured grids,” Computer Methods in Applied Mechanics and Engineering, vol. 187, no. 3, pp. 591–619, 2000.
View at: Publisher Site | Google Scholar
F. L. Addessio, D. E. Carroll, J. K. Dukowicz et al., “Caveat: a computer code for fluid dynamics problems with large distortion and internal slip,” vol. 46, no. 3, pp. 1019–1022, 1992.
View at: Google Scholar
W. E. Johnson, “Oil, a continuous two-dimensional eulerian hydrodynamic code,” Defense Technical Information Center, Fort Belvoir, VA, USA, 1965, Tech. rep.
View at: Google Scholar
D. J. Benson and S. Okazawa, “Contact in a multi-material eulerian finite element formulation,” Computer Methods in Applied Mechanics and Engineering, vol. 193, no. 39-41, pp. 4277–4298, 2004.
View at: Publisher Site | Google Scholar
B. V. Leer, “Towards the ultimate conservative difference scheme. Iv. A new approach to numerical convection,” Journal of Computational Physics, vol. 23, no. 3, pp. 276–299, 1977.
View at: Publisher Site | Google Scholar
B. V. Leer, “Towards the ultimate conservative difference scheme. V - a second-order sequel to godunov's method,” Journal of Computational Physics, vol. 32, no. 1, pp. 101–136, 1997.
View at: Google Scholar
D. J. Benson, “A mixture theory for contact in multi-material eulerian formulations,” Computer Methods in Applied Mechanics and Engineering, vol. 140, no. 1-2, pp. 59–86, 1997.
View at: Publisher Site | Google Scholar
C. W. Hirt and B. D. Nichols, “Volume of fluid (VOF) method for the dynamics of free boundaries,” Journal of Computational Physics, vol. 39, no. 1, pp. 201–225, 1981.
View at: Publisher Site | Google Scholar
L. Olovsson, “Eulerian-lagrangian mapping for finite element analysis,” 2007, US 7167816 B1.
View at: Google Scholar
D. L. Youngs, “An interface tracking method for a 3D eulerian hydrodynamics code,” Scientific Research Publishing, Wuhan, China, 1984.
View at: Google Scholar
C. L. Xin, G. G. Xu, and K. Z. Liu, “Numerical simulation of underwater explosion loads,” Transactions of Tianjin University, vol. 14, no. B10, pp. 519–522, 2008.
View at: Publisher Site | Google Scholar
S. Marrone, “Enhanced SPH modeling of free-surface flows with large deformations,” University of Rome La Sapienza, Rome, Italy, 2012, Ph.D. thesis.
View at: Google Scholar
F. R. Ming, A. M. Zhang, Y. Z. Xue, and S. P. Wang, “Damage characteristics of ship structures subjected to shockwaves of underwater contact explosions,” Ocean Engineering, vol. 117, pp. 359–382, 2016.
View at: Publisher Site | Google Scholar
A. Chernishev, N. Petrov, and A. Schmidt, Numerical Investigation of Processes Accompanying Energy Release in Water Near The Free Surface, 28th International Symposium on Shock Waves, Springer, Berlin, Heidelberg, 2012.
M. Kamegai, C. E. Rosenkilde, and L. S. Klein, “Computer simulation studies on free surface reflection of underwater shock waves,” UCRL, Berkeley, CA, USA, 1987, UCRL-96960.
View at: Google Scholar
N. V. Petrov and A. A. Schmidt, “Multiphase phenomena in underwater explosion,” Experimental Thermal and Fluid Science, vol. 60, pp. 367–373, 2015.
View at: Publisher Site | Google Scholar
M. Dubesset and M. Lavergne, “Calculation of the cavitation due to underwater explosions at small depths,” Acta Acustica United with Acustica, vol. 20, no. 5, pp. 289–298, 1968.
View at: Google Scholar
A. R. Pishevar and R. Amirifar, “An adaptive ale method for underwater explosion simulations including cavitation,” Shock Waves, vol. 20, no. 5, pp. 425–439, 2010.
View at: Publisher Site | Google Scholar
N. A. Fleck and V. Deshpande, “The resistance of clamped sandwich beams to shock loading,” Journal of Applied Mechanics, vol. 71, no. 3, pp. 386–401, 2004.
View at: Publisher Site | Google Scholar
Z. K. Liu and Y. L. Young, “Transient response of submerged plates subject to underwater shock loading: an analytical perspective,” Journal of Applied Mechanics, vol. 75, no. 4, Article ID 044504, 2008.
View at: Publisher Site | Google Scholar
Z. Zong and K. Y. Lam, “Viscoplastic response of a circular plate to an underwater explosion shock,” Acta Mechanica, vol. 148, no. 1-4, pp. 93–104, 2001.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2019 Zi-Fei Meng et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

7148

Downloads

2216

Citations