Table of Contents Author Guidelines Submit a Manuscript
Advances in Materials Science and Engineering
Volume 2011 (2011), Article ID 563410, 8 pages
http://dx.doi.org/10.1155/2011/563410
Research Article

Metallurgical Aspects of Laser Surface Processing of PM Cr-V Ledeburitic Steel

Faculty of Mechanical Engineering, Czech Technical University in Prague, Karlovo Nám. 13, 121 35 Prague 2, Czech Republic

Received 13 July 2010; Revised 23 November 2010; Accepted 6 December 2010

Academic Editor: J. Dutta Majumdar

Copyright © 2011 Peter Jurči et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. P. R. Strutt, H. Nowotny, M. Tuli, and B. H. Kear, “Laser surface melting of high speed tool steels,” Materials Science and Engineering, vol. 36, no. 2, pp. 217–222, 1978. View at Google Scholar · View at Scopus
  2. P. Molian and H. Rajasekhara, “Laser melt injection of BN powders on tool steels I: microhardness and structure,” Wear, vol. 114, no. 1, pp. 19–27, 1987. View at Google Scholar · View at Scopus
  3. P. Jurči, P. Stolař, and I. Dlouhý, “Laser heat treatment of 6-5-2 high speed steels of different production way,” in Proceedings of the 10th Congress of the IFHTE, T. Bell and R. J. Mittemeijer, Eds., vol. 25, Brighton, UK, 1996.
  4. H. Jones, “Modelling of growth and microstructure selection in rapid solidification: a progress report,” Materials Science and Engineering A, vol. 133, pp. 33–39, 1991. View at Google Scholar · View at Scopus
  5. P. F. Nizhnikowskaya, E. P. Kalinushkin, L. M. Snagovskij, and G. F. Demchenko, “Structural formation of high-speed steels during crystallization, Metallovedenie i Termicheskaya Obrabotka Metallov,” Metal Science and Heat Treatment, vol. 24, no. 11, pp. 777–784, 1982. View at Publisher · View at Google Scholar
  6. P. Jurči, O. Honzík, and P. Stolař, “Investigation of laser affected zones on the 19830-grade high speed steel,” Metal Materials, vol. 33, p. 165, 1995. View at Google Scholar
  7. P. Jurči, “Surface remelting of ledeburitic steels by laser,” Metal Letters, vol. 53, p. 12, 1998. View at Google Scholar
  8. R. Colaço and R. Vilar, “Effect of laser surface melting on the tempering behaviour of DIN X42Cr13 stainless tool steel,” Scripta Materialia, vol. 38, no. 1, pp. 107–113, 1997. View at Google Scholar · View at Scopus
  9. R. Colaço and R. Vilar, “Stabilisation of retained austenite in laser surface melted tool steels,” Materials Science and Engineering A, vol. 385, no. 1-2, pp. 123–127, 2004. View at Publisher · View at Google Scholar · View at Scopus
  10. P. Jurči and P. Grgač, “Structural analysis of laser surface remelted CH3F12-alloy,” in Proceedings of the International Conference of Technology, P. Kostka, Ed., Bratislava, Slovakia, September 1993.
  11. P. Jurči, F. Hnilica, J. Suchánek, and P. Stolař, “Microstructural features of Cr-V ledeburitic steel saturated with nitrogen,” Materials and Technology, vol. 38, p. 13, 2004. View at Google Scholar
  12. E. Ramous, “Rapid surface melting,” Materials Science and Engineering A, vol. 178, no. 1-2, pp. 185–188, 1994. View at Google Scholar · View at Scopus
  13. P. Jurči, Preparation and investigation of properties of rapidly solidified powders and compacts of the Fe-C-Cr-V - system, Ph.D. thesis, MtF STU, Trnava, Slovakia, 1996.
  14. P. Juřci, D. Vojtěch, and P. Stolař, “Influence of solidification conditions on microstructure and phase composition of a Fe-4C-12Cr-13V alloy,” Zeitschrift fuer Metallkunde/, vol. 88, no. 9, pp. 733–738, 1997. View at Google Scholar · View at Scopus
  15. R. A. Versaci, “Stability of carbides in M2 high speed steel,” Journal of Materials Science Letters, vol. 7, no. 3, pp. 273–275, 1988. View at Publisher · View at Google Scholar · View at Scopus
  16. K. Stiller, L. E. Svensson, P. R. Howell, W. Rong, H. O. Andrén, and G. L. Dunlop, “High resolution microanalytical study of precipitation in a powder metallurgical high speed steel,” Acta Metallurgica, vol. 32, no. 9, pp. 1457–1467, 1984. View at Google Scholar · View at Scopus
  17. P. Jurči, J. Sobotová, J. Cejp, P. Salabová, and O. Prikner, “Effect of sub-zero treatment on mechanical properties of the vanadis 6 PM ledeburitic tool steel,” in Proceedings of the 19th International Metallurgical and Materials Conference (METAL '10), S. R. O. Tanger, Ed., Rožnov pod Radhoštěm, Czech Republic, May 2010.