Table of Contents Author Guidelines Submit a Manuscript
Advances in Materials Science and Engineering
Volume 2013, Article ID 751971, 7 pages
http://dx.doi.org/10.1155/2013/751971
Research Article

The Kinetics and Dry-Sliding Wear Properties of Boronized Gray Cast Iron

1Department of Mechanical Engineering, Chengdu Technological University, Chengdu 611730, China
2College of Materials Science and Engineering, Sichuan University, Chengdu 610064, China

Received 30 May 2013; Accepted 15 July 2013

Academic Editor: Yong Ding

Copyright © 2013 Dong Mu and Bao-luo Shen. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. H. Berns, “Comparison of wear resistant MMC and white cast iron,” Wear, vol. 254, no. 1-2, pp. 47–54, 2003. View at Publisher · View at Google Scholar · View at Scopus
  2. C. Kowandy, C. Richard, Y.-M. Chen, and J.-J. Tessier, “Correlation between the tribological behaviour and wear particle morphology-case of grey cast iron 250 versus Graphite and PTFE,” Wear, vol. 262, no. 7-8, pp. 996–1006, 2007. View at Publisher · View at Google Scholar · View at Scopus
  3. E. Albertin and A. Sinatora, “Effect of carbide fraction and matrix microstructure on the wear of cast iron balls tested in a laboratory ball mill,” Wear, vol. 250-251, no. 1, pp. 492–501, 2001. View at Publisher · View at Google Scholar · View at Scopus
  4. J. Asensio, J. A. Pero-Sanz, and J. I. Verdeja, “Microstructure selection criteria for cast irons with more than 10 wt.% chromium for wear applications,” Materials Characterization, vol. 49, no. 2, pp. 83–93, 2002. View at Publisher · View at Google Scholar · View at Scopus
  5. B. K. Prasad, O. P. Modi, and H. K. Khaira, “High-stress abrasive wear behaviour of a zinc-based alloy and its composite compared with a cast iron under varying track radius and load conditions,” Materials Science and Engineering A, vol. 381, no. 1-2, pp. 343–354, 2004. View at Publisher · View at Google Scholar · View at Scopus
  6. T. Murakami, T. Inoue, H. Shimura, M. Nakano, and S. Sasaki, “Damping and tribological properties of Fe-Si-C cast iron prepared using various heat treatments,” Materials Science and Engineering A, vol. 432, no. 1-2, pp. 113–119, 2006. View at Publisher · View at Google Scholar · View at Scopus
  7. A. K. Tieu and Y. J. Liu, “Friction variation in the cold-rolling process,” Tribology International, vol. 37, no. 2, pp. 177–183, 2004. View at Publisher · View at Google Scholar · View at Scopus
  8. A. K. Sinha, “Boriding (Boronizing) of steels,” ASM International, Heat Treating, vol. 4, pp. 437–447, 1991. View at Google Scholar
  9. R. H. Biddulph, “Boronizing for erosion resistance,” Thin Solid Films, vol. 45, no. 2, pp. 341–347, 1977. View at Google Scholar · View at Scopus
  10. A. Erdemir and C. Bindal, “Formation and self-lubricating mechanisms of boric acid on borided steel surfaces,” Surface and Coatings Technology, vol. 76-77, no. 1, pp. 443–449, 1995. View at Google Scholar · View at Scopus
  11. O. Torun, R. Gürler, B. Baksan, and I. Celikyürek, “Diffusion bonding of iron aluminide Fe72Al28 using a pure iron interlayer,” Intermetallics, vol. 13, no. 8, pp. 801–804, 2005. View at Publisher · View at Google Scholar · View at Scopus
  12. L. Pan and D. E. Luzzi, “A study on diffusion couples of Ti and polysynthetically twinned (PST) Ti-Al: I. Microstructure characterization,” Intermetallics, vol. 14, no. 1, pp. 61–67, 2006. View at Publisher · View at Google Scholar · View at Scopus
  13. U. Sen, S. Sen, S. Koksal, and F. Yilmaz, “Fracture toughness of borides formed on boronized ductile iron,” Materials and Design, vol. 26, no. 2, pp. 175–179, 2005. View at Publisher · View at Google Scholar · View at Scopus
  14. R. Ipek, B. Selçuk, M. B. Karamiş, V. Kuzucu, and A. Yücel, “An evaluation of the possibilities of using borided GG25 cast iron instead of chilled GG25 cast iron (surface properties),” Journal of Materials Processing Technology, vol. 105, no. 1-2, pp. 73–79, 2000. View at Google Scholar · View at Scopus
  15. U. Sen, S. Sen, and F. Yilmaz, “Effect of copper on boride layer of boronized ductile cast irons,” Vacuum, vol. 72, no. 2, pp. 199–204, 2003. View at Publisher · View at Google Scholar · View at Scopus
  16. C. Meric, S. Sahin, B. Backir, and N. S. Koksal, “Investigation of the boronizing effect on the abrasive wear behavior in cast irons,” Materials and Design, vol. 27, no. 9, pp. 751–757, 2006. View at Publisher · View at Google Scholar · View at Scopus
  17. C. Martini, G. Palombarini, G. Poli, and D. Prandstraller, “Sliding and abrasive wear behaviour of boride coatings,” Wear, vol. 256, no. 6, pp. 608–613, 2004. View at Publisher · View at Google Scholar · View at Scopus
  18. W. Jost, Diffusion in Solids, Liquids, Gases, Academic Press, New York, NY, USA, 3rd edition, 1960.
  19. F.-S. Chen and K.-L. Wang, “The kinetics and mechanism of multi-component diffusion on AISI 1045 steel,” Surface and Coatings Technology, vol. 115, no. 2-3, pp. 239–248, 1999. View at Google Scholar · View at Scopus
  20. I. Campos, O. Bautista, G. Ramírez, M. Islas, J. De La Parra, and L. Zúñiga, “Effect of boron paste thickness on the growth kinetics of Fe2B boride layers during the boriding process,” Applied Surface Science, vol. 243, no. 1–4, pp. 429–436, 2005. View at Publisher · View at Google Scholar · View at Scopus
  21. C. X. Li and T. Bell, “Sliding wear properties of active screen plasma nitrided 316 austenitic stainless steel,” Wear, vol. 256, no. 11-12, pp. 1144–1152, 2004. View at Publisher · View at Google Scholar · View at Scopus