Table of Contents Author Guidelines Submit a Manuscript
Advances in Materials Science and Engineering
Volume 2013, Article ID 930156, 5 pages
http://dx.doi.org/10.1155/2013/930156
Research Article

Influences of Holes Arrangement on Creep Characteristic of Nickel-Base Single Crystal Alloy Blade Cooling Holes

1Department of Engineering Mechanics, Northwestern Polytechnical University, Xi’an, Shaanxi 710072, China
2School of Mechanical Engineering, Northwestern Polytechnical University, Xi’an, Shaanxi 710072, China

Received 27 May 2013; Revised 16 August 2013; Accepted 19 August 2013

Academic Editor: Steven Suib

Copyright © 2013 Lei Li et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. Z. Mazur, A. Luna-Ramírez, J. A. Juárez-Islas, and A. Campos-Amezcuaa, “Failure analysis of a gas turbine blade made of Inconel 738LC alloy,” Engineering Failure Analysis, vol. 12, no. 3, pp. 474–486, 2005. View at Publisher · View at Google Scholar
  2. R. A. Kupkovits and R. W. Neu, “Thermomechanical fatigue of a directionally-solidified Ni-base superalloy: smooth and cylindrically-notched specimens,” International Journal of Fatigue, vol. 32, no. 8, pp. 1330–1342, 2010. View at Publisher · View at Google Scholar · View at Scopus
  3. K. A. Thole, M. Gritsch, A. Schulz, and S. Wittig, “Flowfield measurements for film-cooling holes with expanded exits,” ASME Paper 96-GT-174, 1996. View at Google Scholar
  4. Z. Gao, D. P. Narzary, and J. C. Han, “Film cooling on a gas turbine blade pressure side or suction side with axial shaped holes,” International Journal of Heat and Mass Transfer, vol. 51, no. 9-10, pp. 2139–2152, 2008. View at Publisher · View at Google Scholar · View at Scopus
  5. Y. Lu, D. Allison, and S. V. Ekkad, “Turbine blade showerhead film cooling: influence of hole angle and shaping,” International Journal of Heat and Fluid Flow, vol. 28, no. 5, pp. 922–931, 2007. View at Publisher · View at Google Scholar · View at Scopus
  6. G. I. Taylor, “Plastic strain in metals,” Journal of the Institute of Metals, vol. 62, pp. 307–324, 1938. View at Google Scholar
  7. G. I. Taylor and C. F. Elam, “The distortion of an aluminum crystal during a tensile test,” Proceedings of the Royal Society A, vol. 102, no. 719, pp. 643–667, 1923. View at Publisher · View at Google Scholar
  8. J. Lubliner, Plasticity Theory, Pearson Education, London, UK, 2006.
  9. D. Chatterjee, N. Hazari, N. Das, and R. Mitra, “Microstructure and creep behavior of DMS4-type nickel based superalloy single crystals with orientations near <0 0 1> and <0 1 1>,” Materials Science and Engineering A, vol. 528, no. 2, pp. 604–613, 2010. View at Publisher · View at Google Scholar · View at Scopus
  10. Z. Wen, N. Hou, and Z. Yue, “Creep behaviors of nickel-based single crystal superalloys compact tension specimen at high temperature,” Advanced Materials Research, vol. 146-147, pp. 1322–1326, 2011. View at Publisher · View at Google Scholar · View at Scopus