Table of Contents Author Guidelines Submit a Manuscript
Advances in Materials Science and Engineering
Volume 2014, Article ID 721731, 5 pages
http://dx.doi.org/10.1155/2014/721731
Research Article

Examining the Abrasion Behaviour of PA 66 Gears in Different Cycles

1Hema Endüstri A.S Organized Industrial Zone, Çerkezköy, Tekirdag, Turkey
2Mechanical Education Department, University of Selçuk, Campus, Konya, Turkey

Received 5 December 2013; Revised 7 April 2014; Accepted 7 April 2014; Published 9 June 2014

Academic Editor: Yuanhua Lin

Copyright © 2014 Rifat Yakut and Hayrettin Düzcükoglu. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. B. İşel, Forming a surface fatigue test device for gears and studying the lube temperature effect [M.S. thesis], Afyon Kocatepe University Science Institute, 2007.
  2. H. İmrek and H. Düzcükoğlu, “Relation between wear and tooth width modification in spur gears,” Wear, vol. 262, no. 3-4, pp. 390–394, 2007. View at Google Scholar
  3. K. Kızılaslan, B. İşel, and İ. Yavuz, “Damage types occur on gears,” Machine Technologies Electronical Magazine, vol. 7, no. 1, pp. 119–129, 2010. View at Google Scholar
  4. H. Düzcükoglu, M. T. Demirci, R. Yakut, and Ş. Ekinci, “The effect of contact heat on plastic gear tooth surface to the tooth damage,” in Proceedings of the 5th International Advanced Technologies Symposium (IATS '09), Karabük, Turkey, May 2009.
  5. M. Aksulu and M. Palabıyık, “The effect of opposing surface on abrasion of Poliamid 6,” İTÜ Dergisi/d Engineering, vol. 8, no. 2, pp. 63–71, 2009. View at Google Scholar
  6. R. Yakut, Experimenting with the load capacity and damage occurrence of thermoplastic gears [M.S. thesis], S.Ü. FBE, 2008.
  7. K. Mao, W. Li, C. J. Hooke, and D. Walton, “Friction and wear behaviour of acetal and nylon gears,” Wear, vol. 267, no. 1–4, pp. 639–645, 2009. View at Publisher · View at Google Scholar · View at Scopus
  8. M. Yüksel, “Material information,” in TMMOB-Mechanical Engineers Chamber, vol. 1, pp. 304–338, Denizli Branch Publications, Denizli, Turkey, 1998. View at Google Scholar
  9. N. A. Wright and S. N. Kukureka, “Wear testing and measurement techniques for polymer composite gears,” Wear, vol. 251, no. 1–12, pp. 1567–1578, 2001. View at Google Scholar · View at Scopus
  10. T. Eritenel, S. M. Vijayakar, D. R. Houser, and J. M. Casella, “Effect of tooth deflection and corner contact on backside separation (backlash) of gear pairs,” in Proceedings of the ASME Design Engineering Technical Conferences and Computers and Information in Engineering Conference, pp. 103–110, Chicago, Ill, USA, September 2003. View at Scopus
  11. S. Senthilvelan and R. Gnanamoorthy, “Effect of rotational speed on the performance of unreinforced and glass fiber reinforced Nylon 6 spur gears,” Materials and Design, vol. 28, no. 3, pp. 765–772, 2007. View at Publisher · View at Google Scholar · View at Scopus
  12. H. Düzcükoglu and H. Imrek, “A new method for preventing premature pitting formation on spur gears,” Engineering Fracture Mechanics, vol. 75, no. 15, pp. 4431–4438, 2008. View at Publisher · View at Google Scholar · View at Scopus
  13. H. Düzcükoglu, “PA 66 spur gear durability improvement with tooth width modification,” Materials and Design, vol. 30, no. 4, pp. 1060–1067, 2009. View at Publisher · View at Google Scholar · View at Scopus
  14. H. Düzcükoglu, R. Yakut, and M. T. Demirci, “The load capacity of PC/ABS spur gears and investigation of gear damage,” Archives of Materials Science and Engineering, vol. 40, no. 1, pp. 41–46, 2009. View at Google Scholar · View at Scopus
  15. A. R. Breeds, S. N. Kukureka, K. Mao, D. Walton, and C. J. Hooke, “Wear behaviour of acetal gear pairs,” Wear, vol. 166, no. 1, pp. 85–91, 1993. View at Google Scholar · View at Scopus
  16. N. Tsukamoto, H. Maruyama, and H. Mimura, “Effect of reducing friction of polyacetal in gears,” Transactions of the JSME C, vol. 57, pp. 230–235, 1985. View at Google Scholar
  17. H. Can, Prestressed plastic gear design [M.S. thesis], Gazi University Science Institute, Ankara, Turkey, 2004.