Table of Contents Author Guidelines Submit a Manuscript
Advances in Materials Science and Engineering
Volume 2015, Article ID 613839, 7 pages
http://dx.doi.org/10.1155/2015/613839
Research Article

Microstructure and Texture of Hydrostatic Extrusion Deformed Ni Single Crystals and Polycrystal

1Materials Science and Engineering Faculty, Warsaw University of Technology, Woloska 141, 02-507 Warsaw, Poland
2Institute of High Pressure Physics (Unipress), Polish Academy of Sciences, 01-142 Warsaw, Poland

Received 3 July 2015; Revised 18 August 2015; Accepted 23 August 2015

Academic Editor: Ying Li

Copyright © 2015 D. Jakubowska et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. W. Skrotzki, L. S. Tóth, B. Klöden, H.-G. Brokmeier, and R. Arruffat-Massion, “Texture after ECAP of a cube-oriented Ni single crystal,” Acta Materialia, vol. 56, no. 14, pp. 3439–3449, 2008. View at Publisher · View at Google Scholar · View at Scopus
  2. T. Grosdidier, J.-J. Fundenberger, D. Goran et al., “On microstructure and texture heterogeneities in single crystals deformed by equal channel angular extrusion,” Scripta Materialia, vol. 59, no. 10, pp. 1087–1090, 2008. View at Publisher · View at Google Scholar · View at Scopus
  3. K. Neishi, Z. Horita, and T. G. Langdon, “Grain refinement of pure nickel using equal-channel angular pressing,” Materials Science and Engineering A, vol. 325, no. 1-2, pp. 54–58, 2002. View at Publisher · View at Google Scholar · View at Scopus
  4. A. Zhilyaev, B. Kim, J. Szpunar, M. Baró, and T. Langdon, “The microstructural characteristics of ultrafine-grained nickel,” Materials Science and Engineering A, vol. 391, no. 1-2, pp. 377–389, 2005. View at Publisher · View at Google Scholar
  5. J. Zdunek, J. Mizera, K. Wasik, and K. J. KurzydŁowski, “Microstructural analysis of the 111 and 110 nickel single crystals subjected to severe plastic deformation by hydroextrusion,” Materials Science and Engineering A, vol. 569, pp. 92–95, 2013. View at Publisher · View at Google Scholar · View at Scopus
  6. M. Kulczyk and K. J. Kurzyd, Zastosowanie wyciskania hydrostatycznego do rozdrobnienia ziarna w niklu [Ph.D. thesis], Warsaw University of Technology, Warsaw, Poland, 2007.
  7. P. Bazarnik, B. Romelczyk, M. Kulczyk, and M. Lewandowska, “The strength and ductility of 5483 aluminium alloy processed by various SPD methods,” Materials Science Forum, vol. 765, pp. 423–428, 2013. View at Publisher · View at Google Scholar · View at Scopus
  8. J. Bohlen, S. B. Yi, J. Swiostek, D. Letzig, H. G. Brokmeier, and K. U. Kainer, “Microstructure and texture development during hydrostatic extrusion of magnesium alloy AZ31,” Scripta Materialia, vol. 53, no. 2, pp. 259–264, 2005. View at Publisher · View at Google Scholar · View at Scopus
  9. P. Maj, B. Adamczyk-Cieślak, J. Mizera, W. Pachla, and K. J. Kurzydłowski, “Microstructure and mechanical properties of duplex stainless steel subjected to hydrostatic extrusion,” Materials Characterization, vol. 93, pp. 110–118, 2014. View at Publisher · View at Google Scholar · View at Scopus
  10. S. Zherebtsov, A. Mazur, G. Salishchev, and W. Lojkowski, “Effect of hydrostatic extrusion at 600–700°C on the structure and properties of Ti-6Al-4V alloy,” Materials Science and Engineering A, vol. 485, no. 1-2, pp. 39–45, 2008. View at Publisher · View at Google Scholar · View at Scopus
  11. W. Chrominski, M. Kulczyk, M. Lewandowska, and K. J. Kurzydlowski, “Precipitation strengthening of ultrafine-grained Al-Mg-Si alloy processed by hydrostatic extrusion,” Materials Science and Engineering A, vol. 609, pp. 80–87, 2014. View at Publisher · View at Google Scholar · View at Scopus
  12. I. J. Beyerlein and L. S. Tóth, “Texture evolution in equal-channel angular extrusion,” Progress in Materials Science, vol. 54, no. 4, pp. 427–510, 2009. View at Publisher · View at Google Scholar · View at Scopus
  13. H.-P. Lin, T.-S. Ng, J.-C. Kuo, Y.-C. Chen, C.-L. Chen, and S.-X. Ding, “EBSD study on crystallographic texture and microstructure development of cold-rolled FePd alloy,” Materials Characterization, vol. 93, pp. 163–172, 2014. View at Publisher · View at Google Scholar · View at Scopus
  14. R. E. Reed and C. J. McHargue, “Effect of fabrication method on the texture of aluminum rods,” Transactions of the Metallurgical Society of AIME, vol. 242, 1968. View at Google Scholar
  15. J. Chen, W. Yan, C. X. Liu, R. G. Ding, and X. H. Fan, “Dependence of texture evolution on initial orientation in drawn single crystal copper,” Materials Characterization, vol. 62, no. 2, pp. 237–242, 2011. View at Publisher · View at Google Scholar
  16. M. Kulczyk, W. Pachla, A. Mazur et al., “Microstructure and mechanical properties of nickel deformed by hydrostatic extrusion,” Materials Science, vol. 23, no. 3, pp. 839–846, 2005. View at Google Scholar · View at Scopus
  17. J. Chen, W. Yan, B. Li, X. Ma, X. Du, and X. Fan, “Microstructure and texture evolution of cold drawing 110 single crystal copper,” Science China Technological Sciences, vol. 54, no. 6, pp. 1551–1559, 2011. View at Publisher · View at Google Scholar
  18. H. Wenk, Preferred Orientation in Deformed Metals and Rocks: An Introduction to Modern Texture Analysis, Elsevier, 1985.