Table of Contents Author Guidelines Submit a Manuscript
Advances in Materials Science and Engineering
Volume 2017, Article ID 1384305, 9 pages
https://doi.org/10.1155/2017/1384305
Research Article

Experimental and Numerical Studies on Residual Stress in Wide Butt Welds

1Department of Civil Engineering, Tianjin University, Tianjin 300072, China
2Key Laboratory of Coast Civil Structure Safety, Ministry of Education, Tianjin University, Tianjin 300072, China

Correspondence should be addressed to Jia-Bao Yan; moc.361@jnayeec

Received 2 August 2016; Revised 23 November 2016; Accepted 25 December 2016; Published 15 January 2017

Academic Editor: Antti Salminen

Copyright © 2017 Yang Ding et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. Y. Ding, Principles of Steel Structure Design, Press of Tianjin University, Tianjin, China, 2004 (Chinese).
  2. China Standard, “Code for the design of steel structures,” GB 50017-2003, China Standard Press, 2003 (Chinese).
  3. “Code for welding ofsteel structures,” GB 50661-2011, China Standard Press, 2011 (Chinese).
  4. X. P. Zhang and N. Wang, “Measurement of welding residual stress in the heavy converter using blind-hole method,” Mechanics in Engineering, vol. 29, no. 3, pp. 45–49, 2007. View at Google Scholar
  5. Z. L. Zhou, M. Xie, and J. Q. Jiao, “Investigation of welding residual stress in the integrative linking part of Yangzi River Bridge,” Journal of Dalian Railway Institute, vol. 19, no. 3, pp. 79–84, 1998. View at Google Scholar
  6. S.-Z. Tian and F.-C. Li, “A method for testing residual weld stress in beam and plane components,” Journal of Harbin Engineering University, vol. 20, no. 5, pp. 501–507, 2009. View at Publisher · View at Google Scholar · View at Scopus
  7. N. Wang, Researchon Measuring Welding Residual Stressof Plateof Moderate Thickness Using Blind-hole Method, Dalian Technology University, Dalian, China, 2007 (Chinese).
  8. Y.-H. Huang, R.-H. Wang, and Q. Gan, “Experiment on welding residual stress of integral joint for steel truss bridge,” Zhongguo Gonglu Xuebao/China Journal of Highway and Transport, vol. 24, no. 1, pp. 83–88, 2011. View at Google Scholar · View at Scopus
  9. Y.-B. Wang, G.-Q. Li, and S.-W. Chen, “Residual stresses in welded flame-cut high strength steel H-sections,” Journal of Constructional Steel Research, vol. 79, pp. 159–165, 2012. View at Publisher · View at Google Scholar · View at Scopus
  10. Y.-B. Wang, G.-Q. Li, and S.-W. Chen, “The assessment of residual stresses in welded high strength steel box sections,” Journal of Constructional Steel Research, vol. 76, pp. 93–99, 2012. View at Publisher · View at Google Scholar · View at Scopus
  11. Y. Pei, Y. F. Bao, and N. Y. Tang, “Effect of boundary and distance between holes on accuracy of blind-hole technique,” Welding Institution, vol. 15, no. 3, pp. 191–195, 1994. View at Google Scholar
  12. ASTM, “Standard test methods and definitions for mechanical testing of steel products,” ASTM A370-13, American Society for Testing and Materials, 2013. View at Google Scholar
  13. ASTM, “Standard test method for determining residual stresses by the hole-drilling strain-gage method,” ASTM E837-08, American Society for Testing and Materials, 2008. View at Google Scholar
  14. CB 3395-92, Test Method for Determining Residual Stresses-Hole-Drillingmethod, China State Shipbuilding Corporation, Beijing, China, 1992 (Chinese).
  15. C. Heinze, A. Pittner, M. Rethmeier, and S. S. Babu, “Dependency of martensite start temperature on prior austenite grain size and its influence on welding-induced residual stresses,” Computational Materials Science, vol. 69, pp. 251–260, 2013. View at Publisher · View at Google Scholar · View at Scopus
  16. M. Zubairuddin, S. K. Albert, S. Mahadevan, M. Vasudevan, V. Chaudhari, and V. K. Suri, “Experimental and finite element analysis of residual stress and distortion in GTA welding of modified 9Cr-1Mo steel,” Journal of Mechanical Science and Technology, vol. 28, no. 12, pp. 5095–5105, 2014. View at Publisher · View at Google Scholar · View at Scopus
  17. J. Goldak, A. Chakravarti, and M. Bibby, “A new finite element model for welding heat sources,” Metallurgical Transactions B, vol. 15, no. 2, pp. 299–305, 1984. View at Publisher · View at Google Scholar · View at Scopus
  18. P. Ferro, H. Porzner, A. Tiziani, and F. Bonollo, “The influence of phase transformations on residual stresses induced by the welding process—3D and 2D numerical models,” Modelling and Simulation in Materials Science and Engineering, vol. 14, no. 2, pp. 117–136, 2006. View at Publisher · View at Google Scholar · View at Scopus
  19. D. P. Koistinen and R. E. Marburger, “A general equation prescribing the extent of the austenite-martensite transformation in pure iron-carbon alloys and plain carbon steels,” Acta Metallurgica, vol. 7, no. 1, pp. 59–60, 1959. View at Publisher · View at Google Scholar · View at Scopus
  20. S. A. Tsirkas, P. Papanikos, and T. Kermanidis, “Numerical simulation of the laser welding process in butt-joint specimens,” Journal of Materials Processing Technology, vol. 134, no. 1, pp. 59–69, 2003. View at Publisher · View at Google Scholar · View at Scopus
  21. Y. N. Zhao, Z. N. Zhang, and L. G. Jia, “General research situation of residual stress,” Steel Engineering Research, vol. 17, no. 1, pp. 195–201, 2012. View at Google Scholar