Table of Contents Author Guidelines Submit a Manuscript
Advances in Materials Science and Engineering
Volume 2017, Article ID 1691465, 13 pages
https://doi.org/10.1155/2017/1691465
Research Article

Statistical Model for the Mechanical Properties of Al-Cu-Mg-Ag Alloys at High Temperatures

1Mechanical Engineering Department, College of Engineering, King Saud University, P.O. Box 800, Riyadh 11421, Saudi Arabia
2Mechanical Engineering Department, King Abdulaziz University, Jeddah, Saudi Arabia
3Industrial Engineering Department, College of Engineering, King Saud University, P.O. Box 800, Riyadh 11421, Saudi Arabia
4Physics & Astronomy Department, Faculty of Science, King Saud University, P.O. Box 2455, Riyadh 11451, Saudi Arabia
5King Abdullah Institute for Nanotechnology (KAIN), King Saud University, Riyadh, Saudi Arabia

Correspondence should be addressed to E. A. El-Danaf; as.ude.usk@fanade

Received 2 March 2017; Revised 15 May 2017; Accepted 1 June 2017; Published 9 July 2017

Academic Editor: Markus Bambach

Copyright © 2017 A. M. Al-Obaisi et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. M. Gazizov and R. Kaibyshev, “Low-cyclic fatigue behaviour of an Al–Cu–Mg–Ag alloy under T6 and T840 conditions,” Materials Science and Technology (United Kingdom), pp. 1–11, 2016. View at Publisher · View at Google Scholar · View at Scopus
  2. P. Lequeu, “Advances in aerospace aluminum,” Advanced Materials & Processes, pp. 47–49, 2008. View at Google Scholar
  3. M. Macar, Investigation of Dynamics of Behavior of Aluminum Alloy Armor Materials [Ph.D. thesis], Middle East technical University, 2014.
  4. J. C. Williams and E. A. Starke Jr., “Progress in structural materials for aerospace systems,” Acta Materialia, vol. 51, no. 19, pp. 5775–5799, 2003. View at Publisher · View at Google Scholar · View at Scopus
  5. J. S. Robinson, R. L. Cudd, and J. T. Evans, “Creep resistant aluminium alloys and their applications,” Materials Science and Technology, vol. 19, no. 2, pp. 143–155, 2003. View at Publisher · View at Google Scholar · View at Scopus
  6. C. L. Lach and M. S. Domack, “Characterization of Al-Cu-Mg-Ag Alloy RX226-T8 Plate,” NASA/TM-2003-212639, 2003. View at Google Scholar
  7. S. Bai, P. Ying, Z. Liu, J. Wang, and J. Li, “Quantitative transmission electron microscopy and atom probe tomography study of Ag-dependent precipitation of Ω phase in Al-Cu-Mg alloys,” Materials Science and Engineering: A, vol. 687, pp. 8–16, 2017. View at Publisher · View at Google Scholar
  8. S. Bai, X. Zhou, Z. Liu, P. Xia, M. Liu, and S. Zeng, “Effects of Ag variations on the microstructures and mechanical properties of Al-Cu-Mg alloys at elevated temperatures,” Materials Science and Engineering A, vol. 611, pp. 69–76, 2014. View at Publisher · View at Google Scholar · View at Scopus
  9. D. Bakavos, P. B. Prangnell, B. Bes, and F. Eberl, “The effect of silver on microstructural evolution in two 2xxx series Al-alloys with a high Cu:Mg ratio during ageing to a T8 temper,” Materials Science and Engineering A, vol. 491, no. 1-2, pp. 214–223, 2008. View at Publisher · View at Google Scholar · View at Scopus
  10. R. N. Lumley and I. J. Polmear, “The effect of long term creep exposure on the microstructure and properties of an underaged Al-Cu-Mg-Ag alloy,” Scripta Materialia, vol. 50, no. 9, pp. 1227–1231, 2004. View at Publisher · View at Google Scholar · View at Scopus
  11. B. M. Gable, G. J. Shiflet, and J. Starke, “Alloy development for the enhanced stability of Ω precipitates in Al-Cu-Mg-Ag alloys,” Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science, vol. 37, no. 4, pp. 1091–1105, 2006. View at Publisher · View at Google Scholar · View at Scopus
  12. D. H. Xiao, J. N. Wang, D. Y. Ding, and H. L. Yang, “Effect of rare earth Ce addition on the microstructure and mechanical properties of an Al-Cu-Mg-Ag alloy,” Journal of Alloys and Compounds, vol. 352, no. 1-2, pp. 84–88, 2003. View at Publisher · View at Google Scholar · View at Scopus
  13. S. Bai, Z. Liu, Y. Li, Y. Hou, and X. Chen, “Microstructures and fatigue fracture behavior of an Al-Cu-Mg-Ag alloy with addition of rare earth Er,” Materials Science and Engineering A, vol. 527, no. 7-8, pp. 1806–1814, 2010. View at Publisher · View at Google Scholar · View at Scopus
  14. A. Cho and B. Bes, “Damage tolerance capability of an Al-Cu-Mg-Ag alloy(2139),” Materials Science Forum, vol. 519-521, no. 1, pp. 603–608, 2006. View at Publisher · View at Google Scholar · View at Scopus
  15. M. Song, K.-H. Chen, and L.-P. Huang, “Effects of Ag addition on mechanical properties and microstructures of Al-8Cu-0.5Mg alloy,” Transactions of Nonferrous Metals Society of China (English Edition), vol. 16, no. 4, pp. 766–771, 2006. View at Publisher · View at Google Scholar · View at Scopus
  16. Q. K. Xia, Z. Y. Liu, and Y. T. Li, “Microstructure and properties of Al-Cu-Mg-Ag alloy exposed at 200°C with and without stress,” Transactions of Nonferrous Metals Society of China (English Edition), vol. 18, no. 4, pp. 789–794, 2008. View at Publisher · View at Google Scholar · View at Scopus
  17. X. Y. Liu, Q. L. Pan, X. L. Zhang et al., “Creep behavior and microstructural evolution of deformed Al-Cu-Mg-Ag heat resistant alloy,” Materials Science and Engineering A, vol. 599, pp. 160–165, 2014. View at Publisher · View at Google Scholar · View at Scopus
  18. R. N. Lumley, A. J. Morton, and I. J. Polmear, “Enhanced creep performance in an Al-Cu-Mg-Ag alloy through underageing,” Acta Materialia, vol. 50, no. 14, pp. 3597–3608, 2002. View at Publisher · View at Google Scholar · View at Scopus
  19. A. M. Al-Obaisi, E. A. El-Danaf, A. E. Ragab, and M. S. Soliman, “Precipitation Hardening and Statistical Modeling of the Aging Parameters and Alloy Compositions in Al-Cu-Mg-Ag Alloys,” Journal of Materials Engineering and Performance, pp. 1–13, 2016. View at Publisher · View at Google Scholar · View at Scopus
  20. J. C. Lourenço, M. I. S. T. Faria, A. Robin, L. P. Prisco, and M. C. Puccini, “Influence of process parameters on localized corrosion of AA7075 alloy during the production of aeronautic components,” Materials and Corrosion, vol. 66, no. 12, pp. 1498–1503, 2015. View at Publisher · View at Google Scholar · View at Scopus
  21. T. A. El-Taweel and S. Haridy, “An application of fractional factorial design in wire electrochemical turning process,” International Journal of Advanced Manufacturing Technology, vol. 75, no. 5-8, pp. 1207–1218, 2014. View at Publisher · View at Google Scholar · View at Scopus
  22. E. M. Salleh, H. Zuhailawati, S. Ramakrishnan, and M. A.-H. Gepreel, “A statistical prediction of density and hardness of biodegradable mechanically alloyed Mg-Zn alloy using fractional factorial design,” Journal of Alloys and Compounds, vol. 644, pp. 476–484, 2015. View at Publisher · View at Google Scholar · View at Scopus
  23. I. J. Polmear and M. J. Couper, “Design and development of an experimental wrought aluminum alloy for use at elevated temperatures,” Metallurgical Transactions A, vol. 19, no. 4, pp. 1027–1035, 1988. View at Publisher · View at Google Scholar · View at Scopus
  24. K. M. Knowles and W. M. Stobbs, “The structure of 111 age‐hardening precipitates in Al–Cu–Mg–Ag alloys,” Acta Crystallographica Section B, vol. 44, no. 3, pp. 207–227, 1988. View at Publisher · View at Google Scholar · View at Scopus
  25. B. C. Muddle and I. J. Polmear, “The precipitate Ω phase in Al-Cu-Mg-Ag alloys,” Acta Metallurgica, vol. 37, no. 3, pp. 777–789, 1989. View at Publisher · View at Google Scholar · View at Scopus
  26. A. Garg, Y. C. Chang, and J. M. Howe, “Precipitation of the Ω phase in an Al-4.0Cu-0.5Mg alloy,” Scripta Metallurgica et Materiala, vol. 24, no. 4, pp. 677–680, 1990. View at Publisher · View at Google Scholar · View at Scopus
  27. M. Grujicic, G. Arakere, C.-F. Yen, and B. A. Cheeseman, “Computational investigation of hardness evolution during friction-stir welding of AA5083 and AA2139 aluminum alloys,” Journal of Materials Engineering and Performance, vol. 20, no. 7, pp. 1097–1108, 2011. View at Publisher · View at Google Scholar · View at Scopus