Table of Contents Author Guidelines Submit a Manuscript
Advances in Materials Science and Engineering
Volume 2017, Article ID 3709171, 6 pages
https://doi.org/10.1155/2017/3709171
Research Article

A Novel Silica-Nylon Mesh Reinforcement for Dental Prostheses

1Department of Dental Materials and Prosthodontics, Institute of Science and Technology, São Paulo State University (Unesp), São José dos Campos, SP, Brazil
2Postgraduation Program in Prosthodontics, Department of Dental Materials and Prosthodontics, Institute of Science and Technology, São Paulo State University (Unesp), São José dos Campos, SP, Brazil
3Postgraduation Program in Dentistry, Dental School, University of Passo Fundo, Passo Fundo, RS, Brazil
4Postdoctoral Program, Institute of Aeronautics Technology (ITA), São José dos Campos, SP, Brazil

Correspondence should be addressed to Tarcisio José de Arruda Paes-Junior; rb.psenu.cjsof@oisicrat

Received 9 June 2017; Revised 25 August 2017; Accepted 12 September 2017; Published 16 October 2017

Academic Editor: Jun Liu

Copyright © 2017 Tarcisio José de Arruda Paes-Junior et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. D. A. Felton, “Edentulism and comorbid factors,” Journal of Prosthodontics, vol. 18, no. 2, pp. 88–96, 2009. View at Publisher · View at Google Scholar · View at Scopus
  2. V. P. Reitz, J. L. Sanders, and B. Levin, “The curing of denture acrylic resins by microwave energy—physical properties,” Quintessence International, vol. 16, pp. 547–551, 1985. View at Google Scholar
  3. J. P. De Clerck, “Microwave polymerization of acrylic resins used in dental prostheses,” The Journal of Prosthetic Dentistry, vol. 57, no. 5, pp. 650–658, 1987. View at Publisher · View at Google Scholar · View at Scopus
  4. B. Levin, J. L. Sanders, and P. V. Reitz, “The use of microwave energy for processing acrylic resins,” The Journal of Prosthetic Dentistry, vol. 61, no. 3, pp. 381–383, 1989. View at Publisher · View at Google Scholar · View at Scopus
  5. S. R. Shlosberg, C. J. Goodacre, C. A. Munoz, B. K. Moore, and R. J. Shnell, “Microwave energy polymerization of poly (methyl methacrylate) denture base resin,” The International Journal of Prosthodontics, vol. 2, pp. 453–458, 1989. View at Google Scholar
  6. P. K. Vallittu, “Comparison of two different silane compounds used for improving adhesion between fibres and acrylic denture base material.,” Journal of Oral Rehabilitation, vol. 20, no. 5, pp. 533–539, 1993. View at Publisher · View at Google Scholar · View at Scopus
  7. O. M. Doǧan, G. Bolayir, S. Keskin, A. Doǧan, B. Bek, and A. Boztuǧ, “The effect of esthetic fibers on impact resistance of a conventional heat-cured denture base resin,” Dental Materials, vol. 26, no. 2, pp. 232–239, 2007. View at Publisher · View at Google Scholar · View at Scopus
  8. C. S. Almeida, M. Amaral, F. De Cássia Papaiz Gonçalves, and T. J. De Arruda Paes, “Effect of an experimental silica-nylon reinforcement on the fracture load and flexural strength of bisacrylic interim partial fixed dental prostheses,” Journal of Prosthetic Dentistry, vol. 115, no. 3, pp. 301–305, 2016. View at Publisher · View at Google Scholar · View at Scopus
  9. K. J. Anusavice, Phillips Science of Dental Materials, Saunders, St. Louis, MO, USA, 12 edition, 2012.
  10. D. C. Jagger, A. Harrison, R. G. Jagger, and P. Milward, “The effect of the addition of poly(methyl methacrylate) fibres on some properties of high strength heat-cured acrylic resin denture base material,” Journal of Oral Rehabilitation, vol. 30, no. 3, pp. 231–235, 2003. View at Publisher · View at Google Scholar · View at Scopus
  11. P. K. Vallittu, H. Vojtkova, and V. P. Lassila, “Impact strength of denture polymethyl methacrylate reinforced with continuous glass fibers or metal wire,” Acta Odontologica Scandinavica, vol. 53, no. 6, pp. 392–396, 1995. View at Publisher · View at Google Scholar · View at Scopus
  12. D. L. Dixon and L. C. Breeding, “The transverse strengths of three denture base resins reinforced with polyethylene fibers,” The Journal of Prosthetic Dentistry, vol. 67, no. 3, pp. 417–419, 1992. View at Publisher · View at Google Scholar · View at Scopus
  13. L. M. Fais, L. A. P. Pinelli, R. H. B. T. Silva, J. C. M. Segalla, and C. C. Marcelo, “Efeito da ciclagem mecânica sobre a resistência flexural de resinas acrílicas reforçadas por fibras de vidro,” RFO UPF, vol. 11, pp. 21–25, 2006. View at Google Scholar
  14. J. B. Woelfel, “Processing complete dentures,” Dental Clinics of North America, vol. 21, pp. 329–338, 1977. View at Google Scholar
  15. International Standardization Organization, “Dentistry—Base polymers—Part 1: Denture base polymers. ISO 20795-1, Genéve,” 2013.
  16. J. John, S. A. Gangadhar, and I. Shah, “Flexural strength of heat-polymerized polymethyl methacrylate denture resin reinforced with glass, aramid, or nylon fibers,” Journal of Prosthetic Dentistry, vol. 86, no. 4, pp. 424–427, 2001. View at Publisher · View at Google Scholar · View at Scopus
  17. I. Kostoulas, V. T. Kavoura, M. J. Frangou, and G. L. Polyzois, “Fracture force, deflection, and toughness of acrylic denture repairs involving glass fiber reinforcement,” Journal of Prosthodontics, vol. 17, no. 4, pp. 257–261, 2008. View at Publisher · View at Google Scholar · View at Scopus
  18. D. C. Jagger, A. Harrison, and K. D. Jandt, “The reinforcement of dentures,” Journal of Oral Rehabilitation, vol. 26, no. 3, pp. 185–194, 1999. View at Publisher · View at Google Scholar · View at Scopus
  19. A. D. Bona, K. J. Anusavice, and P. H. DeHoff, “Weibull analysis and flexural strength of hot-pressed core and veneered ceramic structures,” Dental Materials, vol. 19, no. 7, pp. 662–669, 2003. View at Publisher · View at Google Scholar · View at Scopus
  20. J. M. D. S. N. Reis, C. E. Vergani, A. C. Pavarina, E. T. Giampaolo, and A. L. Machado, “Effect of relining, water storage and cyclic loading on the flexural strength of a denture base acrylic resin,” Journal of Dentistry, vol. 34, no. 7, pp. 420–426, 2006. View at Publisher · View at Google Scholar · View at Scopus
  21. R. S. Seo, H. Murata, G. Hong, C. E. Vergani, and T. Hamada, “Influence of thermal and mechanical stresses on the strength of intact and relined denture bases,” Journal of Prosthetic Dentistry, vol. 96, no. 1, pp. 59–67, 2006. View at Publisher · View at Google Scholar · View at Scopus
  22. G. S. Chandu, P. Asnani, S. Gupta, and M. F. Khan, “Comparative evaluation of effect of water absorption on the surface properties of heat cure acrylic: an in vitro study,” Journal of International Oral Health, vol. 7, pp. 63–68, 2015. View at Google Scholar