Table of Contents Author Guidelines Submit a Manuscript
Advances in Materials Science and Engineering
Volume 2017 (2017), Article ID 5853687, 10 pages
https://doi.org/10.1155/2017/5853687
Research Article

Combustion and Mechanical Properties of Polymer-Modified Cement Mortar at High Temperature

1Hazard Mitigation Evaluation Technology Center, Korea Conformity Laboratories, Cheongju 28115, Republic of Korea
2Department of Building System Engineering, Kangwon National University, Samcheok 25913, Republic of Korea

Correspondence should be addressed to Won-Jun Park; rk.ca.nowgnak@krapjw

Received 22 March 2017; Accepted 7 June 2017; Published 11 July 2017

Academic Editor: Michele Zappalorto

Copyright © 2017 Hyung-Jun Kim and Won-Jun Park. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. Y. Ohama, “Polymer-based admixtures,” Cement and Concrete Composites, vol. 20, no. 2-3, pp. 189–212, 1998. View at Publisher · View at Google Scholar · View at Scopus
  2. ACI Committee 548, State-Of-The-Art Report on Polymer Modified Concrete (548.3R-95), Farmington Hills, MI, USA, American Concrete Institute.
  3. Y. Ohama, Handbook of Polymer-Modified Concrete and Mortars, Properties and Process Technology, Noyes Publications, Park Ridge, NJ, USA, 1995.
  4. K. P. Grosskurth and A. Konietzko, “Structure and mechanical behaviour of polymer modified cement concrete,” in Proceeding of 5th International Congress on Polymers in Concrete, pp. 171–174, 1987.
  5. M. Wang, R. Wang, H. Yao et al., “Research on the mechanism of polymer latex modified cement,” Construction and Building Materials, vol. 111, pp. 710–718, 2016. View at Publisher · View at Google Scholar · View at Scopus
  6. L. K. Aggarwal, P. C. Thapliyal, and S. R. Karade, “Properties of polymer-modified mortars using epoxy and acrylic emulsions,” Construction and Building Materials, vol. 21, no. 2, pp. 379–383, 2007. View at Publisher · View at Google Scholar · View at Scopus
  7. D. Park, J. Ahn, S. Oh, H. Song, and T. Noguchi, “Drying effect of polymer-modified cement for patch-repaired mortar on constraint stress,” Construction and Building Materials, vol. 23, no. 1, pp. 434–447, 2009. View at Publisher · View at Google Scholar · View at Scopus
  8. D. Park, S. Park, Y. Seo, and T. Noguchi, “Water absorption and constraint stress analysis of polymer-modified cement mortar used as a patch repair material,” Construction and Building Materials, vol. 28, no. 1, pp. 819–830, 2012. View at Publisher · View at Google Scholar · View at Scopus
  9. J. Mirza, M. S. Mirza, and R. Lapointe, “Laboratory and field performance of polymer-modified cement-based repair mortars in cold climates,” Construction and Building Materials, vol. 16, no. 6, pp. 365–374, 2002. View at Publisher · View at Google Scholar · View at Scopus
  10. A. Yahia, “Shear-thickening behavior of high-performance cement grouts - Influencing mix-design parameters,” Cement and Concrete Research, vol. 41, no. 3, pp. 230–235, 2011. View at Publisher · View at Google Scholar · View at Scopus
  11. C. A. Anagnostopoulos, G. Sapidis, and E. Papastergiadis, “Fundamental properties of epoxy resin-modified cement grouts,” Construction and Building Materials, vol. 125, pp. 184–195, 2016. View at Publisher · View at Google Scholar · View at Scopus
  12. J.-P. Won, S.-W. Choi, C.-G. Park, and C.-I. Jang, “High strength polymer-modified repair cementitious composite for fire protection,” Polymers and Polymer Composites, vol. 15, no. 5, pp. 379–388, 2007. View at Google Scholar · View at Scopus
  13. J.-P. Won, H.-B. Kang, S.-J. Lee, and J.-W. Kang, “Eco-friendly fireproof high-strength polymer cementitious composites,” Construction and Building Materials, vol. 30, pp. 406–412, 2012. View at Publisher · View at Google Scholar · View at Scopus
  14. Y. Qiao, J. K. Deliwala, S. S. Chakravarthula, and X. Kong, “High-temperature tensile properties of a polymer intercalated/exfoliated cement,” Materials Letters, vol. 59, no. 28, pp. 3616–3619, 2005. View at Publisher · View at Google Scholar · View at Scopus
  15. H. Hamasaki, H. J. Kim, and T. Noguchi, “Study on heat release properties of polymer-modified cement mortar,” in Proceedings of the Part 1 Effect of the Unit Polymer Weight and Mixed Design, pp. 435-436, 2009.
  16. H. J Kim, H. hamasaki, and T. Noguchi, “Study on heat release properties of polymer-modified cement mortar,” in Proceedings of the Part 2 Effect on the Thickness of Specimen on Annual Conference of Architectural Institute of Japan, pp. 437-438, 2009.
  17. ISO, ISO 5660-1:2015 Reaction-to-fire tests -- Heat release, smoke production and mass loss rate - Part 1: Heat release rate (cone calorimeter method) and smoke production rate (dynamic measurement), Geneva. Switzerland: International Organization for Standardization; 2015.
  18. ISO, ISO 1182: Reaction to fire tests for building products - Non-combustibility test, Geneva. Switzerland: International Organization for Standardization; 2010.
  19. JIS, JIS A 9523, Loose fill thermal insulation materials, Japanese Standards Association; 2016.