Table of Contents Author Guidelines Submit a Manuscript
Advances in Materials Science and Engineering
Volume 2017, Article ID 6373190, 8 pages
https://doi.org/10.1155/2017/6373190
Research Article

Study on the High Temperature Friction and Wear Behaviors of Cu-Based Friction Pairs in Wet Clutches by Pin-on-Disc Tests

1School of Mechanical Engineering, Beijing Institute of Technology, Beijing, China
2Collaborative Innovation Center of Electric Vehicles in Beijing, Beijing, China

Correspondence should be addressed to He-Yan Li; nc.ude.tib@nayehvol

Received 10 January 2017; Revised 2 May 2017; Accepted 8 May 2017; Published 29 May 2017

Academic Editor: Carlos Navarro

Copyright © 2017 Er-Hui Zhao et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. H. Gao, G. C. Barber, and M. Shillor, “Numerical simulation of engagement of a wet clutch with skewed surface roughness,” Journal of Tribology, vol. 124, no. 2, pp. 305–312, 2002. View at Publisher · View at Google Scholar · View at Scopus
  2. J. Deur, J. Petric, J. Asgari, and D. Hrovat, “Modeling of wet clutch engagement including a thorough experimental validation,” SAE Technical Papers, 2005. View at Publisher · View at Google Scholar · View at Scopus
  3. A. P. Ompusunggu, P. Sas, and H. Van Brussel, “Modeling and simulation of the engagement dynamics of a wet friction clutch system subjected to degradation: An application to condition monitoring and prognostics,” Mechatronics, vol. 23, no. 6, pp. 700–712, 2013. View at Publisher · View at Google Scholar · View at Scopus
  4. S. Iqbal, F. Al-Bender, A. P. Ompusunggu, B. Pluymers, and W. Desmet, “Modeling and analysis of wet friction clutch engagement dynamics,” Mechanical Systems and Signal Processing, vol. 60-61, pp. 420–436, 2015. View at Publisher · View at Google Scholar · View at Scopus
  5. M. Mansouri, M. Holgerson, M. M. Khonsari, and W. Aung, “Thermal and dynamic characterization of wet clutch engagement with provision for drive Torque,” Journal of Tribology, vol. 123, no. 2, pp. 313–323, 2001. View at Publisher · View at Google Scholar · View at Scopus
  6. T.-C. Jen and D. J. Nemecek, “Thermal analysis of a wet-disk clutch subjected to a constant energy engagement,” International Journal of Heat and Mass Transfer, vol. 51, no. 7-8, pp. 1757–1769, 2008. View at Publisher · View at Google Scholar · View at Scopus
  7. M. Ingram, T. Reddyhoff, and H. A. Spikes, “Thermal behaviour of a slipping wet clutch contact,” Tribology Letters, vol. 41, no. 1, pp. 23–32, 2011. View at Publisher · View at Google Scholar · View at Scopus
  8. H. Seo, C. Zheng, W. Lim, S. W. Cha, and S. Han, “Temperature prediction model of wet clutch in coupling,” in Proceedings of the 7th IEEE Vehicle Power and Propulsion Conference, VPPC 2011, pp. 1–4, IEEE, Chicago, IL, USA, September 2011. View at Publisher · View at Google Scholar · View at Scopus
  9. L. Wenbin, H. Jianfeng, F. Jie, C. Liyun, and Y. Chunyan, “Simulation and application of temperature field of carbon fabric wet clutch during engagement based on finite element analysis,” International Communications in Heat and Mass Transfer, vol. 71, pp. 180–187, 2016. View at Publisher · View at Google Scholar · View at Scopus
  10. X. Xiong, J. Chen, P. Yao, S. Li, and B. Huang, “Friction and wear behaviors and mechanisms of Fe and SiO2 in Cu-based P/M friction materials,” Wear, vol. 262, no. 9-10, pp. 1182–1186, 2007. View at Publisher · View at Google Scholar · View at Scopus
  11. W. Ost, P. De Baets, and J. Degrieck, “The tribological behaviour of paper friction plates for wet clutch application investigated on SAE#II and pin-on-disk test rigs,” Wear, vol. 249, no. 5-6, pp. 361–371, 2001. View at Publisher · View at Google Scholar · View at Scopus
  12. P. Nyman, R. Mäki, R. Olsson, and B. Ganemi, “Influence of surface topography on friction characteristics in wet clutch applications,” Wear, vol. 261, no. 1, pp. 46–52, 2006. View at Publisher · View at Google Scholar · View at Scopus
  13. P.-P. Yao, H.-C. Sheng, X. Xiong, and B.-Y. Huang, “Worn surface characteristics of Cu-based powder metallurgy bake materials for aircraft,” Transactions of Nonferrous Metals Society of China, vol. 17, no. 1, pp. 99–103, 2007. View at Publisher · View at Google Scholar · View at Scopus
  14. X. Zhou, P. Walker, N. Zhang, B. Zhu, and J. Ruan, “Numerical and experimental investigation of drag torque in a two-speed dual clutch transmission,” Mechanism and Machine Theory, vol. 79, pp. 46–63, 2014. View at Publisher · View at Google Scholar · View at Scopus
  15. M. Li, M. M. Khonsari, D. M. C. McCarthy, and J. Lundin, “On the wear prediction of the paper-based friction materialin a wet clutch,” Wear, vol. 334-335, pp. 56–66, 2015. View at Publisher · View at Google Scholar · View at Scopus
  16. G. Pica, C. Cervone, A. Senatore, M. Lupo, and F. Vasca, “Dry dual clutch torque model with temperature and slip speed effects,” Intelligent Industrial Systems, vol. 2, no. 2, pp. 133–147, 2016. View at Publisher · View at Google Scholar
  17. T. Gong, P. Yao, Y. Xiao et al., “Wear map for a copper-based friction clutch material under oil lubrication,” Wear, vol. 328-329, pp. 270–276, 2015. View at Publisher · View at Google Scholar · View at Scopus
  18. M. Hoic, N. Kranjcevic, Z. Herold, J. Deur, and V. Ivanovic, “Experimental characterization and modeling of dry dual clutch wear,” SAE International Journal of Passenger Cars-Mechanical Systems, vol. 7, no. 1, pp. 326–337, 2014. View at Publisher · View at Google Scholar · View at Scopus