Table of Contents Author Guidelines Submit a Manuscript
Advances in Materials Science and Engineering
Volume 2017, Article ID 8723239, 23 pages
https://doi.org/10.1155/2017/8723239
Review Article

A Review of Additive Mixed-Electric Discharge Machining: Current Status and Future Perspectives for Surface Modification of Biomedical Implants

1Centre for Intelligent Signal and Imaging Research, Universiti Teknologi PETRONAS, Bandar Seri Iskandar, Perak, Malaysia
2Mechanical Engineering Department, University Technology PETRONAS, Bandar Seri Iskandar, Perak, Malaysia
3School of Mechanical Engineering, Lovely Professional University, Phagwara, Punjab 144411, India
4Faculty of Machine Manufacturing & Industrial Management, Gheorghe Asachi Technical University of Iaşi, 59 A Prof. Dimitrie, Iaşi, Romania
5Manufacturing Section, Universiti Kuala Lumpur Malaysian Spanish Institute, Kulim Hi-Tech Park, 09000 Kedah, Malaysia

Correspondence should be addressed to Ahmad Majdi Abdul-Rani; ym.ude.ptu@idjam

Received 23 April 2017; Accepted 1 August 2017; Published 13 September 2017

Academic Editor: Patrice Berthod

Copyright © 2017 Abdul’Azeez Abdu Aliyu et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. V. García Navas, I. Ferreres, J. A. Marañón, C. Garcia-Rosales, and J. Gil Sevillano, “Electro-discharge machining (EDM) versus hard turning and grinding-Comparison of residual stresses and surface integrity generated in AISI O1 tool steel,” Journal of Materials Processing Technology, vol. 195, no. 1–3, pp. 186–194, 2008. View at Publisher · View at Google Scholar · View at Scopus
  2. S. Clijsters, K. Liu, D. Reynaerts, and B. Lauwers, “EDM technology and strategy development for the manufacturing of complex parts in SiSiC,” Journal of Materials Processing Technology, vol. 210, no. 4, pp. 631–641, 2010. View at Publisher · View at Google Scholar · View at Scopus
  3. A. A. Aliyu, H. Musa, and J. M. Rohani, “Parametric study of powder mixed electrical discharge machining and mathematical modeling of SiSiC using copper electrode,” Advanced Materials Research, vol. 845, pp. 878–882, 2014. View at Publisher · View at Google Scholar · View at Scopus
  4. S. Barman, Vijay, Nagahanumaiah, and A. B. Puri, “Surface Texture and Elemental Characterization of High Aspect Ratio Blind Micro Holes on Different Materials in Micro EDM,” Procedia Materials Science, vol. 6, pp. 304–309, 2014. View at Publisher · View at Google Scholar
  5. A. M. Nanimina, A. M. Abdul Rani, and T. L. Ginta, “Assessment of powder mixed EDM: A review,” in Proceedings of the 4th International Conference on Production, Energy and Reliability, ICPER 2014, June 2014. View at Publisher · View at Google Scholar · View at Scopus
  6. Y. Pachaury and P. Tandon, “An overview of electric discharge machining of ceramics and ceramic based composites,” Journal of Manufacturing Processes, vol. 25, pp. 369–390, 2017. View at Publisher · View at Google Scholar · View at Scopus
  7. F. L. Amorim and W. L. Weingaertner, “Die-sinking electrical discharge machining of a high-strength copper-based alloy for injection molds,” Journal of the Brazilian Society of Mechanical Sciences and Engineering, vol. 26, no. 2, pp. 137–144, 2004. View at Google Scholar · View at Scopus
  8. I. Cabanes, E. Portillo, M. Marcos, and J. A. Sánchez, “An industrial application for on-line detection of instability and wire breakage in wire EDM,” Journal of Materials Processing Technology, vol. 195, no. 1-3, pp. 101–109, 2008. View at Publisher · View at Google Scholar · View at Scopus
  9. M. A. Volosova, A. A. Okunkova, D. E. Povolotskiy, and P. A. Podrabinnik, “Study of electrical discharge machining for the parts of nuclear industry usage,” Mechanics & Industry, vol. 16, no. 7, p. 706, 2015. View at Publisher · View at Google Scholar
  10. C. Prakash, H. K. Kansal, B. S. Pabla, S. Puri, and A. Aggarwal, “Electric discharge machining - A potential choice for surface modification of metallic implants for orthopedic applications: A review,” Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, vol. 230, no. 2, pp. 331–353, 2016. View at Publisher · View at Google Scholar · View at Scopus
  11. C. Prakash, H. K. Kansal, B. S. Pabla, and S. Puri, “Experimental investigations in powder mixed electric discharge machining of Ti–35Nb–7Ta–5Zrβ-titanium alloy,” Materials and Manufacturing Processes, vol. 32, no. 3, pp. 274–285, 2017. View at Publisher · View at Google Scholar · View at Scopus
  12. A. M. Abdul-Rani, A. M. Nanimina, T. L. Ginta, and M. A. Razak, “Machined Surface Quality in Nano Aluminum Mixed Electrical Discharge Machining,” Procedia Manufacturing, vol. 7, pp. 510–517, 2017. View at Publisher · View at Google Scholar · View at Scopus
  13. F. Iacono, C. Pirani, L. Generali et al., “Wear analysis and cyclic fatigue resistance of electro discharge machined NiTi rotary instruments,” Giornale Italiano di Endodonzia, vol. 30, no. 1, pp. 64–68, 2016. View at Publisher · View at Google Scholar · View at Scopus
  14. A. Ntasi, W. D. Mueller, G. Eliades, and S. Zinelis, “The effect of Electro Discharge Machining (EDM) on the corrosion resistance of dental alloys,” Dental Materials, vol. 26, no. 12, pp. e237–e245, 2010. View at Publisher · View at Google Scholar · View at Scopus
  15. C. Prakash, H. K. Kansal, B. S. Pabla, and S. Puri, “To optimize the surface roughness and microhardness of β-Ti alloy in PMEDM process using Non-dominated Sorting Genetic Algorithm-II,” in Proceedings of the 2nd International Conference on Recent Advances in Engineering and Computational Sciences, RAECS 2015, Chandigarh, India, December 2015. View at Publisher · View at Google Scholar · View at Scopus
  16. M. T. Mohammed, Z. A. Khan, and A. N. Siddiquee, “Surface Modifications of Titanium Materials for developing Corrosion Behavior in Human Body Environment: A Review,” Procedia Materials Science, vol. 6, pp. 1610–1618, 2014. View at Publisher · View at Google Scholar
  17. A. M. Abdul-Rani, M. A. Razak, G. Littlefair, I. Gibson, and A. M. Nanimina, “Improving EDM Process on AZ31 Magnesium Alloy towards Sustainable Biodegradable Implant Manufacturing,” Procedia Manufacturing, vol. 7, pp. 504–509, 2017. View at Publisher · View at Google Scholar · View at Scopus
  18. M. A. Razak, A. M. Abdul-Rani, T. V. V. L. N. Rao, S. R. Pedapati, and S. Kamal, “Electrical Discharge Machining on Biodegradable AZ31 Magnesium Alloy Using Taguchi Method,” Procedia Engineering, vol. 148, pp. 916–922, 2016. View at Publisher · View at Google Scholar · View at Scopus
  19. P.-W. Peng, K.-L. Ou, H.-C. Lin, Y.-N. Pan, and C.-H. Wang, “Effect of electrical-discharging on formation of nanoporous biocompatible layer on titanium,” Journal of Alloys and Compounds, vol. 492, no. 1-2, pp. 625–630, 2010. View at Publisher · View at Google Scholar · View at Scopus
  20. R. Zou, Z. Yu, W. Li, M. Guo, and J. Li, “Influence of porous structure on the machining performance of micro EDM,” Journal of Materials Processing Technology, vol. 232, pp. 43–51, 2016. View at Publisher · View at Google Scholar · View at Scopus
  21. H. Hermawan, D. Ramdan, and J. R. Djuansjah, Metals for Biomedical Applications, INTECH, 2011.
  22. M. Niinomi, “Mechanical biocompatibilities of titanium alloys for biomedical applications,” Journal of the Mechanical Behavior of Biomedical Materials, vol. 1, no. 1, pp. 30–42, 2008. View at Publisher · View at Google Scholar · View at Scopus
  23. M. Geetha, A. K. Singh, R. Asokamani, and A. K. Gogia, “Ti based biomaterials, the ultimate choice for orthopaedic implants—a review,” Progress in Materials Science, vol. 54, no. 3, pp. 397–425, 2009. View at Publisher · View at Google Scholar · View at Scopus
  24. C. K. Seal, K. Vince, and M. A. Hodgson, “Biodegradable surgical implants based on magnesium alloys - A review of current research,” in Proceedings of the IOP Conference Series: Materials Science and Engineering, IOP Publishing, 2009. View at Publisher · View at Google Scholar · View at Scopus
  25. F. Witte, “The history of biodegradable magnesium implants: a review,” Acta Biomaterialia, vol. 6, no. 5, pp. 1680–1692, 2010. View at Publisher · View at Google Scholar · View at Scopus
  26. N. T. Kirkland, N. Birbilis, and M. P. Staiger, “Assessing the corrosion of biodegradable magnesium implants: A critical review of current methodologies and their limitations,” Acta Biomaterialia, vol. 8, no. 3, pp. 925–936, 2012. View at Publisher · View at Google Scholar · View at Scopus
  27. Y. Chen, Z. Xu, C. Smith, and J. Sankar, “Recent advances on the development of magnesium alloys for biodegradable implants,” Acta Biomaterialia, vol. 10, no. 11, pp. 4561–4573, 2014. View at Publisher · View at Google Scholar · View at Scopus
  28. H. F. Li and Y. F. Zheng, “Recent advances in bulk metallic glasses for biomedical applications,” Acta Biomaterialia, vol. 36, pp. 1–20, 2016. View at Publisher · View at Google Scholar · View at Scopus
  29. Y. Sun, Y. Huang, H. Fan et al., “In vitro and in vivo biocompatibility of an Ag-bearing Zr-based bulk metallic glass for potential medical use,” Journal of Non-Crystalline Solids, vol. 419, pp. 82–91, 2015. View at Publisher · View at Google Scholar · View at Scopus
  30. J. F. Löffler, “Bulk metallic glasses,” Intermetallics, vol. 11, no. 6, pp. 529–540, 2003. View at Publisher · View at Google Scholar · View at Scopus
  31. D. C. Hofmann, “Bulk Metallic Glasses and Their Composites: A Brief History of Diverging Fields,” Journal of Materials, vol. 2013, Article ID 517904, 8 pages, 2013. View at Publisher · View at Google Scholar
  32. W. Ge, B. Li, E. Axinte, Z. Zhang, C. Shang, and Y. Wang, “Crystallization and Corrosion Resistance in Different Aqueous Solutions of Zr50.7Ni28Cu9Al12.3 Amorphous Alloy and Its Crystallization Counterparts,” JOM, vol. 69, no. 4, pp. 776–783, 2017. View at Publisher · View at Google Scholar · View at Scopus
  33. J. C. E. Odekerken, T. J. M. Welting, J. J. C. Arts, G. H. I. M. Walenkamp, and P. J. Emans, “Modern orthopaedic implant coatings—their pro’s, con’s and evaluation method,” in Modern Surface Engineering Treatments, pp. 45–73, InTech, New York, USA, 2013. View at Google Scholar
  34. R. I. M. Asri, W. S. W. Harun, M. A. Hassan, S. A. C. Ghani, and Z. Buyong, “A review of hydroxyapatite-based coating techniques: Sol-gel and electrochemical depositions on biocompatible metals,” Journal of the Mechanical Behavior of Biomedical Materials, vol. 57, pp. 95–108, 2016. View at Publisher · View at Google Scholar · View at Scopus
  35. S. V. Dorozhkin, “Calcium orthophosphate deposits: Preparation, properties and biomedical applications,” Materials Science and Engineering C, vol. 55, pp. 272–326, 2015. View at Publisher · View at Google Scholar · View at Scopus
  36. Y. Zhang, Y. Liu, Y. Shen, R. Ji, Z. Li, and C. Zheng, “Investigation on the influence of the dielectrics on the material removal characteristics of EDM,” Journal of Materials Processing Technology, vol. 214, no. 5, pp. 1052–1061, 2014. View at Publisher · View at Google Scholar · View at Scopus
  37. F. Klocke, M. Schwade, A. Klink, and A. Kopp, “EDM machining capabilities of magnesium (Mg) alloy WE43 for medical applications,” Procedia Engineering, vol. 19, pp. 190–195, 2011. View at Publisher · View at Google Scholar · View at Scopus
  38. M. Kolli and A. Kumar, “Surfactant and graphite powder-assisted electrical discharge machining of titanium alloy,” Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, vol. 231, no. 4, pp. 641–657, 2017. View at Publisher · View at Google Scholar · View at Scopus
  39. A. Batish, A. Bhattacharya, V. K. Singla, and G. Singh, “Study of material transfer mechanism in die steels using powder mixed electric discharge machining,” Materials and Manufacturing Processes, vol. 27, no. 4, pp. 449–456, 2012. View at Publisher · View at Google Scholar · View at Scopus
  40. J. S. Soni and G. Chakraverti, “Experimental investigation on migration of material during EDM of die steel (T215 Cr12),” Journal of Materials Processing Technology, vol. 56, no. 1-4, pp. 439–451, 1996. View at Publisher · View at Google Scholar · View at Scopus
  41. X. Liu, P. K. Chu, and C. Ding, “Surface modification of titanium, titanium alloys, and related materials for biomedical applications,” Materials Science and Engineering R: Reports, vol. 47, no. 3-4, pp. 49–121, 2004. View at Publisher · View at Google Scholar · View at Scopus
  42. Q. Chen and G. A. Thouas, “Metallic implant biomaterials,” Materials Science and Engineering R: Reports, vol. 87, pp. 1–57, 2014. View at Publisher · View at Google Scholar · View at Scopus
  43. X. Wang, S. Xu, S. Zhou et al., “Topological design and additive manufacturing of porous metals for bone scaffolds and orthopaedic implants: a review,” Biomaterials, vol. 83, no. 6, pp. 127–141, 2016. View at Publisher · View at Google Scholar
  44. M. J. Mirzaali, J. J. Schwiedrzik, S. Thaiwichai et al., “Mechanical properties of cortical bone and their relationships with age, gender, composition and microindentation properties in the elderly,” Bone, vol. 93, pp. 196–211, 2016. View at Publisher · View at Google Scholar · View at Scopus
  45. F. Libonati and L. Vergani, “Understanding the structure-property relationship in cortical bone to design a biomimetic composite,” Composite Structures, vol. 139, pp. 188–198, 2016. View at Publisher · View at Google Scholar · View at Scopus
  46. J.-Y. Rho, L. Kuhn-Spearing, and P. Zioupos, “Mechanical properties and the hierarchical structure of bone,” Medical Engineering & Physics, vol. 20, no. 2, pp. 92–102, 1998. View at Publisher · View at Google Scholar · View at Scopus
  47. J. E. Lemons, “Dental implant biomaterials.,” The Journal of the American Dental Association, vol. 121, no. 6, pp. 716–719, 1990. View at Publisher · View at Google Scholar · View at Scopus
  48. D. F. Williams, “On the nature of biomaterials,” Biomaterials, vol. 30, no. 30, pp. 5897–5909, 2009. View at Publisher · View at Google Scholar · View at Scopus
  49. A. King and J. R. A. Phillips, “Total hip and knee replacement surgery,” Surgery (United Kingdom), vol. 34, no. 9, pp. 468–474, 2016. View at Publisher · View at Google Scholar · View at Scopus
  50. C. J. DeFrances, C. A. Lucas, V. C. Buie, and A. Golosinskiy, “2006 national hospital discharge survey,” National Health Statistics Reports, vol. 5, pp. 1–20, 2008. View at Google Scholar
  51. M. M. Dewidar, K. A. Khalil, and J. K. Lim, “Processing and mechanical properties of porous 316L stainless steel for biomedical applications,” Transactions of Nonferrous Metals Society of China (English Edition), vol. 17, no. 3, pp. 468–473, 2007. View at Publisher · View at Google Scholar · View at Scopus
  52. Y. Oshida, E. B. Tuna, O. Aktören, and K. Gençay, “Dental implant systems,” International Journal of Molecular Sciences, vol. 11, no. 4, pp. 1580–1678, 2010. View at Publisher · View at Google Scholar · View at Scopus
  53. K. L. Ong, B. M. Yun, and J. B. White, “New biomaterials for orthopedic implants,” Orthopedic Research and Reviews, vol. 7, pp. 107–130, 2015. View at Publisher · View at Google Scholar · View at Scopus
  54. S.-H. Lee, N. Nomura, and A. Chiba, “Significant improvement in mechanical properties of biomedical Co-Cr-Mo alloys with combination of N addition and Cr-enrichment,” Materials Transactions, vol. 49, no. 2, pp. 260–264, 2008. View at Publisher · View at Google Scholar · View at Scopus
  55. K. Yang and Y. Ren, “Nickel-free austenitic stainless steels for medical applications,” Science and Technology of Advanced Materials, vol. 11, no. 1, p. 014105, 2016. View at Publisher · View at Google Scholar
  56. E. Axinte, A. Bofu, Y. Wang et al., “An overview on the conventional and nonconventional methods for manufacturing the metallic glasses,” MATEC Web of Conferences, vol. 112, p. 03003, 2017. View at Publisher · View at Google Scholar
  57. M. H. Fathi, M. Salehi, A. Saatchi, V. Mortazavi, and S. B. Moosavi, “In vitro corrosion behavior of bioceramic, metallic, and bioceramic-metallic coated stainless steel dental implants,” Dental Materials, vol. 19, no. 3, pp. 188–198, 2003. View at Publisher · View at Google Scholar · View at Scopus
  58. C. A. Schuh, T. C. Hufnagel, and U. Ramamurty, “Mechanical behavior of amorphous alloys,” Acta Materialia, vol. 55, no. 12, pp. 4067–4109, 2007. View at Publisher · View at Google Scholar · View at Scopus
  59. Y. Liu, G. Wang, H. Li, S. Pang, K. Chen, and T. Zhang, “Ti–Cu–Zr–Fe–Sn–Si–Sc bulk metallic glasses with good mechanical properties for biomedical applications,” Journal of Alloys and Compounds, vol. 679, pp. 341–349, 2016. View at Publisher · View at Google Scholar
  60. B. M. Stronach, M. D. Roach, and K. R. St. John, “Failure of Emperion modular femoral stem with implant analysis,” Arthroplasty Today, vol. 2, no. 1, pp. 11–14, 2016. View at Publisher · View at Google Scholar · View at Scopus
  61. L. Guerra-Fuentes, E. Garcia-Sanchez, A. Juarez-Hernandez, and M. A. L. Hernandez-Rodriguez, “Failure analysis in 316L stainless steel supracondylar blade plate,” Engineering Failure Analysis, vol. 57, pp. 243–247, 2015. View at Publisher · View at Google Scholar · View at Scopus
  62. M. A. L. Hernandez-Rodriguez, G. R. Contreras-Hernandez, A. Juarez-Hernandez, B. Beltran-Ramirez, and E. Garcia-Sanchez, “Failure analysis in a dental implant,” Engineering Failure Analysis, vol. 57, pp. 236–242, 2015. View at Publisher · View at Google Scholar · View at Scopus
  63. B. Gervais, A. Vadean, M. Raison, and M. Brochu, “Failure analysis of a 316L stainless steel femoral orthopedic implant,” Case Studies in Engineering Failure Analysis, vol. 5-6, pp. 30–38, 2016. View at Publisher · View at Google Scholar · View at Scopus
  64. C. Kanchanomai, V. Phiphobmongkol, and P. Muanjan, “Fatigue failure of an orthopedic implant - A locking compression plate,” Engineering Failure Analysis, vol. 15, no. 5, pp. 521–530, 2008. View at Publisher · View at Google Scholar · View at Scopus
  65. H. Amel-Farzad, M. T. Peivandi, and S. M. R. Yusof-Sani, “In-body corrosion fatigue failure of a stainless steel orthopaedic implant with a rare collection of different damage mechanisms,” Engineering Failure Analysis, vol. 14, no. 7, pp. 1205–1217, 2007. View at Publisher · View at Google Scholar · View at Scopus
  66. J. Marcomini, C. A. R. P. Baptista, J. P. Pascon, R. L. Teixeira, and F. P. Reis, “Investigation of a fatigue failure in a stainless steel femoral plate,” Journal of the Mechanical Behavior of Biomedical Materials, vol. 38, pp. 52–58, 2014. View at Publisher · View at Google Scholar · View at Scopus
  67. Y. Yang, K.-H. Kim, and J. L. Ong, “A review on calcium phosphate coatings produced using a sputtering process—an alternative to plasma spraying,” Biomaterials, vol. 26, no. 3, pp. 327–337, 2005. View at Publisher · View at Google Scholar · View at Scopus
  68. H.-W. Kim, H.-E. Kim, and J. C. Knowles, “Fluor-hydroxyapatite sol-gel coating on titanium substrate for hard tissue implants,” Biomaterials, vol. 25, no. 17, pp. 3351–3358, 2004. View at Publisher · View at Google Scholar · View at Scopus
  69. M. H. Fathi and A. Doost Mohammadi, “Preparation and characterization of sol-gel bioactive glass coating for improvement of biocompatibility of human body implant,” Materials Science and Engineering A, vol. 474, no. 1-2, pp. 128–133, 2008. View at Publisher · View at Google Scholar · View at Scopus
  70. B. R. Gligorijević, M. Vilotijević, M. Šćepanović, D. Vidović, and N. A. Radović, “Surface structural heterogeneity of high power plasma-sprayed hydroxyapatite coatings,” Journal of Alloys and Compounds, vol. 687, pp. 421–430, 2016. View at Publisher · View at Google Scholar · View at Scopus
  71. H. Xu, X. Geng, G. Liu et al., “Deposition, nanostructure and phase composition of suspension plasma-sprayed hydroxyapatite coatings,” Ceramics International, vol. 42, no. 7, pp. 8684–8690, 2016. View at Publisher · View at Google Scholar
  72. Z. Ur Rahman, I. Shabib, and W. Haider, “Surface characterization and cytotoxicity analysis of plasma sprayed coatings on titanium alloys,” Materials Science and Engineering: C, vol. 67, pp. 675–683, 2016. View at Publisher · View at Google Scholar
  73. O. Blind, L. H. Klein, B. Dailey, and L. Jordan, “Characterization of hydroxyapatite films obtained by pulsed-laser deposition on Ti and Ti-6AL-4v substrates,” Dental Materials, vol. 21, no. 11, pp. 1017–1024, 2005. View at Publisher · View at Google Scholar · View at Scopus
  74. Q. Bao, C. Chen, D. Wang, Q. Ji, and T. Lei, “Pulsed laser deposition and its current research status in preparing hydroxyapatite thin films,” Applied Surface Science, vol. 252, no. 5, pp. 1538–1544, 2005. View at Publisher · View at Google Scholar · View at Scopus
  75. C. F. Koch, S. Johnson, D. Kumar et al., “Pulsed laser deposition of hydroxyapatite thin films,” Materials Science and Engineering C, vol. 27, no. 3, pp. 484–494, 2007. View at Publisher · View at Google Scholar · View at Scopus
  76. G. P. Dinda, J. Shin, and J. Mazumder, “Pulsed laser deposition of hydroxyapatite thin films on Ti-6Al-4V: Effect of heat treatment on structure and properties,” Acta Biomaterialia, vol. 5, no. 5, pp. 1821–1830, 2009. View at Publisher · View at Google Scholar · View at Scopus
  77. J. Huang, S. N. Jayasinghe, S. M. Best et al., “Novel deposition of nano-sized silicon substituted hydroxyapatite by electrostatic spraying,” Journal of Materials Science: Materials in Medicine, vol. 16, no. 12, pp. 1137–1142, 2005. View at Publisher · View at Google Scholar · View at Scopus
  78. M. C. Siebers, X. F. Walboomers, S. C. G. Leeuwenburgh, J. G. C. Wolke, and J. A. Jansen, “Electrostatic spray deposition (ESD) of calcium phosphate coatings, an in vitro study with osteoblast-like cells,” Biomaterials, vol. 25, no. 11, pp. 2019–2027, 2004. View at Publisher · View at Google Scholar · View at Scopus
  79. S. C. G. Leeuwenburgh, M. C. Heine, J. G. C. Wolke, S. E. Pratsinis, J. Schoonman, and J. A. Jansen, “Morphology of calcium phosphate coatings for biomedical applications deposited using Electrostatic Spray Deposition,” Thin Solid Films, vol. 503, no. 1-2, pp. 69–78, 2006. View at Publisher · View at Google Scholar · View at Scopus
  80. A. Stoch, A. Brozek, G. Kmita, J. Stoch, W. Jastrz, and A. Rakowska, “Electrophoretic coating of hydroxyapatite on titanium implants,” Journal of Molecular Structure, vol. 596, no. 1-3, pp. 191–200, 2001. View at Publisher · View at Google Scholar · View at Scopus
  81. D. Stojanovic, B. Jokic, D. Veljovic, R. Petrovic, P. S. Uskokovic, and D. Janackovic, “Bioactive glass-apatite composite coating for titanium implant synthesized by electrophoretic deposition,” Journal of the European Ceramic Society, vol. 27, no. 2-3, pp. 1595–1599, 2007. View at Publisher · View at Google Scholar · View at Scopus
  82. C. T. Kwok, P. K. Wong, F. T. Cheng, and H. C. Man, “Characterization and corrosion behavior of hydroxyapatite coatings on Ti6Al4V fabricated by electrophoretic deposition,” Applied Surface Science, vol. 255, no. 13-14, pp. 6736–6744, 2009. View at Publisher · View at Google Scholar · View at Scopus
  83. J. Li, H. Liao, and L. Hermansson, “Sintering of partially-stabilized zirconia and partially-stabilized zirconia-hydroxyapatite composites by hot isostatic pressing and pressureless sintering,” Biomaterials, vol. 17, no. 18, pp. 1787–1790, 1996. View at Publisher · View at Google Scholar · View at Scopus
  84. T. Onoki, K. Hosoi, and T. Hashida, “New technique for bonding hydroxyapatite ceramics and titanium by the hydrothermal hot-pressing method,” Scripta Materialia, vol. 52, no. 8, pp. 767–770, 2005. View at Publisher · View at Google Scholar · View at Scopus
  85. B. Mavis and A. C. Taş, “Dip coating of calcium hydroxyapatite on Ti-6Al-4V substrates,” Journal of the American Ceramic Society, vol. 83, no. 4, pp. 989–991, 2000. View at Publisher · View at Google Scholar · View at Scopus
  86. S.-L. Chen, M.-H. Lin, G.-X. Huang, and C.-C. Wang, “Research of the recast layer on implant surface modified by micro-current electrical discharge machining using deionized water mixed with titanium powder as dielectric solvent,” Applied Surface Science, vol. 311, pp. 47–53, 2014. View at Publisher · View at Google Scholar · View at Scopus
  87. B. E. J. Lee, S. Ho, G. Mestres, M. Karlsson Ott, P. Koshy, and K. Grandfield, “Dual-topography electrical discharge machining of titanium to improve biocompatibility,” Surface and Coatings Technology, vol. 296, pp. 149–156, 2016. View at Publisher · View at Google Scholar · View at Scopus
  88. H. Marashi, A. A. D. Sarhan, and M. Hamdi, “Employing Ti nano-powder dielectric to enhance surface characteristics in electrical discharge machining of AISI D2 steel,” Applied Surface Science, vol. 357, pp. 892–907, 2015. View at Publisher · View at Google Scholar · View at Scopus
  89. N. Ekmekci and B. Ekmekci, “Electrical Discharge Machining of Ti6Al4V in Hydroxyapatite Powder Mixed Dielectric Liquid,” Materials and Manufacturing Processes, vol. 31, no. 13, pp. 1663–1670, 2016. View at Publisher · View at Google Scholar · View at Scopus
  90. N. Ekmekci and B. Ekmekci, “Hydroxyapatite deposition onto Ti-6Al-4V surface in powder mixed electrical discharge machining,” Advanced Materials Research, vol. 856, pp. 205–209, 2014. View at Publisher · View at Google Scholar · View at Scopus
  91. S.-L. Chen, M.-H. Lin, C.-C. Chen, and K.-L. Ou, “Effect of electro-discharging on formation of biocompatible layer on implant surface,” Journal of Alloys and Compounds, vol. 456, no. 1-2, pp. 413–418, 2008. View at Publisher · View at Google Scholar · View at Scopus
  92. P. Janmanee and A. Muttamara, “Surface modification of tungsten carbide by electrical discharge coating (EDC) using a titanium powder suspension,” Applied Surface Science, vol. 258, no. 19, pp. 7255–7265, 2012. View at Publisher · View at Google Scholar · View at Scopus
  93. C. Eriksson, J. Lausmaa, and H. Nygren, “Interactions between human whole blood and modified TiO2-surfaces: Influence of surface topography and oxide thickness on leukocyte adhesion and activation,” Biomaterials, vol. 22, no. 14, pp. 1987–1996, 2001. View at Publisher · View at Google Scholar · View at Scopus
  94. S. B. Goodman, Z. Yao, M. Keeney, and F. Yang, “The future of biologic coatings for orthopaedic implants,” Biomaterials, vol. 34, no. 13, pp. 3174–3183, 2013. View at Publisher · View at Google Scholar · View at Scopus
  95. W. Habraken, P. Habibovic, M. Epple, and M. Bohner, “Calcium phosphates in biomedical applications: Materials for the future?” Materials Today, vol. 19, no. 2, pp. 69–87, 2016. View at Publisher · View at Google Scholar · View at Scopus
  96. M. H. Fathi and F. Azam, “Novel hydroxyapatite/tantalum surface coating for metallic dental implant,” Materials Letters, vol. 61, no. 4-5, pp. 1238–1241, 2007. View at Publisher · View at Google Scholar · View at Scopus
  97. Y. Wang, H. Yu, C. Chen, and Z. Zhao, “Review of the biocompatibility of micro-arc oxidation coated titanium alloys,” Materials and Design, vol. 85, pp. 640–652, 2015. View at Publisher · View at Google Scholar · View at Scopus
  98. R. A. Surmenev, M. A. Surmeneva, and A. A. Ivanova, “Significance of calcium phosphate coatings for the enhancement of new bone osteogenesis - A review,” Acta Biomaterialia, vol. 10, no. 2, pp. 557–579, 2014. View at Publisher · View at Google Scholar · View at Scopus
  99. B. M. Schumacher, R. Krampitz, and J.-P. Kruth, “Historical phases of EDM development driven by the dual influence of "Market Pull" and "Science Push",” Procedia CIRP, vol. 6, pp. 5–12, 2013. View at Publisher · View at Google Scholar · View at Scopus
  100. G. Kibria, B. Pradhan, and B. Bhattacharyya, “Experimentation and analysis into micro-hole machining in EDM on Ti-6Al-4V alloy using boron carbide powder mixed de-ionized water,” International Journal of Materials, Manufacturing and Design, Academic Research Journals, pp. 17–35, 2012. View at Google Scholar
  101. J. W. Murray, J. Sun, D. V. Patil, T. A. Wood, and A. T. Clare, “Physical and electrical characteristics of EDM debris,” Journal of Materials Processing Technology, vol. 229, pp. 54–60, 2016. View at Publisher · View at Google Scholar · View at Scopus
  102. T. Muthuramalingam and B. Mohan, “A review on influence of electrical process parameters in EDM process,” Archives of Civil and Mechanical Engineering, vol. 15, no. 1, pp. 87–94, 2015. View at Publisher · View at Google Scholar · View at Scopus
  103. N. Mohd Abbas, D. G. Solomon, and M. Fuad Bahari, “A review on current research trends in electrical discharge machining (EDM),” International Journal of Machine Tools and Manufacture, vol. 47, no. 7-8, pp. 1214–1228, 2007. View at Publisher · View at Google Scholar · View at Scopus
  104. A. Al-Khazraji, S. A. Amin, and S. M. Ali, “The effect of SiC powder mixing electrical discharge machining on white layer thickness, heat flux and fatigue life of AISI D2 die steel,” Engineering Science and Technology, an International Journal, vol. 19, no. 3, pp. 1400–1415, 2016. View at Publisher · View at Google Scholar · View at Scopus
  105. S. S. Habib, “Study of the parameters in electrical discharge machining through response surface methodology approach,” Applied Mathematical Modelling, vol. 33, no. 12, pp. 4397–4407, 2009. View at Publisher · View at Google Scholar · View at Scopus
  106. M. Durairaj, D. Sudharsun, and N. Swamynathan, “Analysis of process parameters in wire EDM with stainless steel using single objective Taguchi method and multi objective grey relational grade,” Procedia Engineering, vol. 64, pp. 868–877, 2013. View at Publisher · View at Google Scholar · View at Scopus
  107. H. Dong, Y. Liu, Y. Shen, and X. Wang, “Optimizing Machining Parameters of Compound Machining of Inconel718,” Procedia CIRP, vol. 42, pp. 51–56, 2016. View at Publisher · View at Google Scholar · View at Scopus
  108. G. Kibria, B. R. Sarkar, B. B. Pradhan, and B. Bhattacharyya, “Comparative study of different dielectrics for micro-EDM performance during microhole machining of Ti-6Al-4V alloy,” The International Journal of Advanced Manufacturing Technology, vol. 48, no. 5–8, pp. 557–570, 2010. View at Publisher · View at Google Scholar · View at Scopus
  109. G. Ugrasen, H. V. Ravindra, G. V. Naveen Prakash, and Y. N. Theertha Prasad, “Optimization of Process Parameters in Wire EDM of HCHCr Material Using Taguchi's Technique,” Materials Today: Proceedings, vol. 2, no. 4-5, pp. 2443–2452, 2015. View at Publisher · View at Google Scholar · View at Scopus
  110. W. König, D. F. Dauw, G. Levy, and U. Panten, “EDM-future steps towards the machining of ceramics,” CIRP Annals—Manufacturing Technology, vol. 37, no. 2, pp. 623–631, 1988. View at Publisher · View at Google Scholar · View at Scopus
  111. A. A. A. Aliyu, J. M. Rohani, A. M. A. Rani, and H. Musa, “Optimization of electrical discharge machining parameters of SiSiC through response surface methodology,” Jurnal Teknologi, vol. 79, no. 1, pp. 119–129, 2017. View at Publisher · View at Google Scholar · View at Scopus
  112. S. L. Chen, B. H. Yan, and F. Y. Huang, “Influence of kerosene and distilled water as dielectrics on the electric discharge machining characteristics of Ti-6A1-4V,” Journal of Materials Processing Technology, vol. 87, no. 1-3, pp. 107–111, 1999. View at Publisher · View at Google Scholar · View at Scopus
  113. F. N. Leão and I. R. Pashby, “A review on the use of environmentally-friendly dielectric fluids in electrical discharge machining,” Journal of Materials Processing Technology, vol. 149, no. 1–3, pp. 341–346, 2004. View at Publisher · View at Google Scholar · View at Scopus
  114. Z. Yu, T. Jun, and K. Masanori, “Dry electrical discharge machining of cemented carbide,” Journal of Materials Processing Technology, vol. 149, no. 1-3, pp. 353–357, 2004. View at Publisher · View at Google Scholar · View at Scopus
  115. C. C. Kao, J. Tao, and A. J. Shih, “Near dry electrical discharge machining,” International Journal of Machine Tools and Manufacture, vol. 47, no. 15, pp. 2273–2281, 2007. View at Publisher · View at Google Scholar · View at Scopus
  116. J. Tao, A. J. Shih, and J. Ni, “Experimental study of the dry and near-dry electrical discharge milling processes,” Journal of Manufacturing Science and Engineering, Transactions of the ASME, vol. 130, no. 1, pp. 0110021–0110029, 2008. View at Publisher · View at Google Scholar · View at Scopus
  117. J. Tao, A. J. Shih, and J. Ni, “Near-dry EDM milling of mirror-like surface finish,” International Journal of Electrical Machining, vol. 13, no. 1, pp. 29–33, 2008. View at Google Scholar
  118. S. K. Saha and S. K. Choudhury, “Experimental investigation and empirical modeling of the dry electric discharge machining process,” International Journal of Machine Tools and Manufacture, vol. 49, no. 3-4, pp. 297–308, 2009. View at Publisher · View at Google Scholar · View at Scopus
  119. P. S. Gajjar, H. P. Bhavsar, D. V. Modi, and B. D. Kayasth, “A review on parametric analysis of dry electric discharge machining,” International Journal of Engineering Innovation and Scientific Research, vol. 1, no. 1, 2015. View at Google Scholar
  120. Y. Shen, Y. Liu, and W. Sun, “High-efficient Dry Hybrid Machining of EDM and Arc Machining,” Procedia CIRP, vol. 42, pp. 149–154, 2016. View at Publisher · View at Google Scholar · View at Scopus
  121. W. Konig, F. Klocke, and M. Sparrer, “EDM–sinking using water-based dielectrics and electropolishing–a new manufacturing sequence in tool-making,” in Proceedings of the in Proceedings of the 11th International Symposium on Electromachining (ISEM XI), Lausanne, Switzerland, 1995.
  122. K. Furutani, N. Mohri, N. Saito, H. Takezawa, H. Takezawa, and M. Higashi, “Simultaneous finishing a pair of dies by electrical discharge grinding,” in Rapid Product Development, pp. 263–272, Chapman & Hall, in association with Japan Society for Precision Engineering, London, UK, 1997. View at Google Scholar
  123. M. Kunieda, M. Yoshida, and N. Taniguchi, “Electrical discharge machining in gas,” CIRP Annals - Manufacturing Technology, vol. 46, no. 1, pp. 143–146, 1997. View at Publisher · View at Google Scholar · View at Scopus
  124. B. H. Yan, Y. C. Lin, F. Y. Huang, and C. H. Wang, “Surface modification of SKD 61 during EDM with metal powder in the dielectric,” Materials Transactions, vol. 42, no. 12, pp. 2597–2604, 2001. View at Publisher · View at Google Scholar · View at Scopus
  125. Z. L. Wang, Y. Fang, P. N. Wu, W. S. Zhao, and K. Cheng, “Surface modification process by electrical discharge machining with a Ti powder green compact electrode,” Journal of Materials Processing Technology, vol. 129, no. 1-3, pp. 139–142, 2002. View at Publisher · View at Google Scholar · View at Scopus
  126. J. Simao, H. G. Lee, D. K. Aspinwall, R. C. Dewes, and E. M. Aspinwall, “Workpiece surface modification using electrical discharge machining,” International Journal of Machine Tools and Manufacture, vol. 43, no. 2, pp. 121–128, 2003. View at Publisher · View at Google Scholar · View at Scopus
  127. H. S. Lim, Y. S. Wong, M. Rahman, and M. K. Edwin Lee, “A study on the machining of high-aspect ratio micro-structures using micro-EDM,” Journal of Materials Processing Technology, vol. 140, no. 1–3, pp. 318–325, 2003. View at Publisher · View at Google Scholar · View at Scopus
  128. E. Uhlmann, S. Piltz, and U. Doll, “Machining of micro/miniature dies and moulds by electrical discharge machining - Recent development,” Journal of Materials Processing Technology, vol. 167, no. 2-3, pp. 488–493, 2005. View at Publisher · View at Google Scholar · View at Scopus
  129. E. Uhlmann, S. Piltz, and D. Oberschmidt, “Machining of micro rotational parts by wire electrical discharge grinding,” Production Engineering, vol. 2, no. 3, pp. 227–233, 2008. View at Publisher · View at Google Scholar · View at Scopus
  130. P. Govindan, A. Gupta, S. S. Joshi, A. Malshe, and K. P. Rajurkar, “Single-spark analysis of removal phenomenon in magnetic field assisted dry EDM,” Journal of Materials Processing Technology, vol. 213, no. 7, pp. 1048–1058, 2013. View at Publisher · View at Google Scholar · View at Scopus
  131. S. Joshi, P. Govindan, A. Malshe, and K. Rajurkar, “Experimental characterization of dry EDM performed in a pulsating magnetic field,” CIRP Annals - Manufacturing Technology, vol. 60, no. 1, pp. 239–242, 2011. View at Publisher · View at Google Scholar · View at Scopus
  132. I. Ayesta, B. Izquierdo, J. A. Sánchez et al., “Influence of EDM parameters on slot machining in C1023 aeronautical alloy,” Procedia CIRP, vol. 6, pp. 129–134, 2013. View at Publisher · View at Google Scholar · View at Scopus
  133. E. Uhlmann and D. C. Domingos, “Investigations on vibration-assisted EDM-machining of seal slots in high-temperature resistant materials for turbine components,” Procedia CIRP, vol. 6, pp. 71–76, 2013. View at Publisher · View at Google Scholar · View at Scopus
  134. E. Uhlmann and D. C. Domingos, “Investigations on Vibration-assisted EDM-machining of Seal Slots in High-Temperature Resistant Materials for Turbine Components -Part II,” Procedia CIRP, vol. 42, pp. 334–339, 2016. View at Publisher · View at Google Scholar · View at Scopus
  135. U. S. Yadav and V. Yadava, “Experimental modeling and multiobjective optimization of electrical discharge drilling of aerospace superalloy material,” Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, vol. 229, no. 10, pp. 1764–1780, 2015. View at Publisher · View at Google Scholar · View at Scopus
  136. W. F. Sales, A. R. F. Oliveira, and A. A. Raslan, “Titanium perovskite (CaTiO3) formation in Ti6Al4V alloy using the electrical discharge machining process for biomedical applications,” Surface and Coatings Technology, vol. 307, pp. 1011–1015, 2016. View at Publisher · View at Google Scholar · View at Scopus
  137. M. Shabgard and B. Khosrozadeh, “Investigation of carbon nanotube added dielectric on the surface characteristics and machining performance of Ti–6Al–4V alloy in EDM process,” Journal of Manufacturing Processes, vol. 25, pp. 212–219, 2017. View at Publisher · View at Google Scholar · View at Scopus
  138. P. Peças and E. Henriques, “Electrical discharge machining using simple and powder-mixed dielectric: The effect of the electrode area in the surface roughness and topography,” Journal of Materials Processing Technology, vol. 200, no. 1–3, pp. 250–258, 2008. View at Publisher · View at Google Scholar · View at Scopus
  139. W. Rehbein, H.-P. Schulze, K. Mecke, G. Wollenberg, and M. Storr, “Influence of selected groups of additives on breakdown in EDM sinking,” Journal of Materials Processing Technology, vol. 149, no. 1-3, pp. 58–64, 2004. View at Publisher · View at Google Scholar · View at Scopus
  140. S. K. Choudhary and R. Jadoun, “Current Research development in Dry Electric Discharge Machining (DEDM): Review Paper,” International Journal of Emerging Technology and Advanced Engineering, vol. 4, no. 8, pp. 832–839, 2014. View at Google Scholar
  141. Y.-F. Tzeng and C.-Y. Lee, “Effects of powder characteristics on electrodischarge machining efficiency,” International Journal of Advanced Manufacturing Technology, vol. 17, no. 8, pp. 586–592, 2001. View at Publisher · View at Google Scholar · View at Scopus
  142. R. Toshimitsu, A. Okada, R. Kitada, and Y. Okamoto, “Improvement in Surface Characteristics by EDM with Chromium Powder Mixed Fluid,” Procedia CIRP, vol. 42, pp. 231–235, 2016. View at Publisher · View at Google Scholar · View at Scopus
  143. B. Singh, J. Kumar, and S. Kumar, “Influences of Process Parameters on MRR Improvement in Simple and Powder-Mixed EDM of AA6061/10%SiC Composite,” Materials and Manufacturing Processes, vol. 30, no. 3, pp. 303–312, 2015. View at Publisher · View at Google Scholar · View at Scopus
  144. R. Bajaj, A. K. Tiwari, and A. R. Dixit, “Current Trends in Electric Discharge Machining Using Micro and Nano Powder Materials- A Review,” Materials Today: Proceedings, vol. 2, no. 4-5, pp. 3302–3307, 2015. View at Publisher · View at Google Scholar · View at Scopus
  145. M. Kolli and A. Kumar, “Effect of dielectric fluid with surfactant and graphite powder on Electrical Discharge Machining of titanium alloy using Taguchi method,” Engineering Science and Technology, an International Journal, vol. 18, no. 4, pp. 524–535, 2015. View at Publisher · View at Google Scholar · View at Scopus
  146. B. H. Yan, H. C. Tsai, and F. Y. Huang, “The effect in EDM of a dielectric of a urea solution in water on modifying the surface of titanium,” International Journal of Machine Tools and Manufacture, vol. 45, no. 2, pp. 194–200, 2005. View at Publisher · View at Google Scholar · View at Scopus
  147. L. Liqing and S. Yingjie, “Study of dry EDM with oxygen-mixed and cryogenic cooling approaches,” Procedia CIRP, vol. 6, pp. 344–350, 2013. View at Publisher · View at Google Scholar · View at Scopus
  148. K. Dhakar and A. Dvivedi, “Parametric Evaluation on Near-Dry Electric Discharge Machining,” Materials and Manufacturing Processes, vol. 31, no. 4, pp. 413–421, 2016. View at Publisher · View at Google Scholar · View at Scopus
  149. T.-S. Huang, S.-F. Hsieh, S.-L. Chen, M.-H. Lin, S.-F. Ou, and W.-T. Chang, “Surface modification of TiNi-based shape memory alloys by dry electrical discharge machining,” Journal of Materials Processing Technology, vol. 221, pp. 279–284, 2015. View at Publisher · View at Google Scholar · View at Scopus
  150. O. Gülcan, İ. Uslan, Y. Usta, and C. Çoğun, “Performance and surface alloying characteristics of Cu–Cr and Cu–Mo powder metal tool electrodes in electrical discharge machining,” Machining Science and Technology, vol. 20, no. 4, pp. 523–546, 2016. View at Publisher · View at Google Scholar · View at Scopus
  151. J.-P. Kruth, L. Stevens, L. Froyen, and B. Lauwers, “Study of the White Layer of a Surface Machined by Die-Sinking Electro-Discharge Machining,” CIRP Annals - Manufacturing Technology, vol. 44, no. 1, pp. 169–172, 1995. View at Publisher · View at Google Scholar · View at Scopus
  152. A. Kumar, V. Kumar, and J. Kumar, “Surface crack density and recast layer thickness analysis in WEDM process through response surface methodology,” Machining Science and Technology, vol. 20, no. 2, pp. 201–230, 2016. View at Publisher · View at Google Scholar · View at Scopus
  153. Y. Zhang, Y. Liu, R. Ji, and B. Cai, “Study of the recast layer of a surface machined by sinking electrical discharge machining using water-in-oil emulsion as dielectric,” Applied Surface Science, vol. 257, no. 14, pp. 5989–5997, 2011. View at Publisher · View at Google Scholar · View at Scopus
  154. Y. Zhang, Y. Liu, R. Ji, B. Cai, and H. Li, “Influence of dielectric type on porosity formation on electrical discharge machined surfaces,” Metallurgical and Materials Transactions B: Process Metallurgy and Materials Processing Science, vol. 43, no. 4, pp. 946–953, 2012. View at Publisher · View at Google Scholar · View at Scopus
  155. W. Cao and L. L. Hench, “Bioactive materials,” Ceramics International, vol. 22, no. 6, pp. 493–507, 1996. View at Publisher · View at Google Scholar · View at Scopus
  156. T. Kokubo, H. Kim, and M. Kawashita, “Novel bioactive materials with different mechanical properties,” Biomaterials, vol. 24, no. 13, pp. 2161–2175, 2003. View at Publisher · View at Google Scholar · View at Scopus
  157. J. Strasky, M. Janecek, and P. Harcuba, “Electric discharge machining of Ti-6Al-4V alloy for Biomedical Use,” in Proceedings of Contributed Papers, Part III (WDS' 11), pp. 127–131, 2011.
  158. T.-S. Yang, M.-S. Huang, M.-S. Wang, M.-H. Lin, M.-Y. Tsai, and P.-Y. Wang Wang, “Effect of electrical discharging on formation of nanoporous biocompatible layer on Ti-6Al-4V alloys,” Implant Dentistry, vol. 22, no. 4, pp. 374–379, 2013. View at Publisher · View at Google Scholar · View at Scopus
  159. F. Otsuka, Y. Kataoka, and T. Miyazaki, “Enhanced osteoblast response to electrical discharge machining surface,” Dental Materials Journal, vol. 31, no. 2, pp. 309–315, 2012. View at Publisher · View at Google Scholar · View at Scopus
  160. C. Prakash, H. K. Kansal, B. S. Pabla, and S. Puri, “Processing and Characterization of Novel Biomimetic Nanoporous Bioceramic Surface on β-Ti Implant by Powder Mixed Electric Discharge Machining,” Journal of Materials Engineering and Performance, vol. 24, no. 9, pp. 3622–3633, 2015. View at Publisher · View at Google Scholar · View at Scopus
  161. C. Prakash, H. K. Kansal, B. S. Pabla, and S. Puri, “Effect of surface nano-porosities fabricated by powder mixed electric discharge machining on bone-implant interface: An experimental and finite element study,” Nanoscience and Nanotechnology Letters, vol. 8, no. 10, pp. 815–826, 2016. View at Publisher · View at Google Scholar · View at Scopus
  162. C. Prakash, H. Kansal, B. Pabla, and S. Puri, “On the Influence of Nanoporous Layer Fabricated by PMEDM on β -Ti Implant: Biological and Computational Evaluation of Bone- Implant Interface,” in Proceedings of the 5th International Conference of Materials Processing and Characterization, Hyderabad, India, 2016.
  163. C. Prakash, H. K. Kansal, B. S. Pabla, and S. Puri, “Powder Mixed Electric Discharge Machining: An Innovative Surface Modification Technique to Enhance Fatigue Performance and Bioactivity of β-Ti Implant for Orthopedics Application,” Journal of Computing and Information Science in Engineering, vol. 16, no. 4, Article ID 041006, 2016. View at Publisher · View at Google Scholar · View at Scopus
  164. S. J. Algodi, J. W. Murray, M. W. Fay, A. T. Clare, and P. D. Brown, “Electrical discharge coating of nanostructured TiC-Fe cermets on 304 stainless steel,” Surface and Coatings Technology, vol. 307, pp. 639–649, 2016. View at Publisher · View at Google Scholar · View at Scopus
  165. C. Prakash, H. K. Kansal, B. Pabla, and S. Puri, “Potential of Silicon Powder-Mixed Electro Spark Alloying for Surface Modification of β-Phase Titanium Alloy for Orthopedic Applications,” in Proceedings of the International Conference on Recent Trends in Engineering and Material Sciences (ICEMS-2016), Jaipur, India, March 2016.
  166. Z. J. Xie, Y. J. Mai, W. Q. Lian, S. L. He, and X. H. Jie, “Titanium carbide coating with enhanced tribological properties obtained by EDC using partially sintered titanium electrodes and graphite powder mixed dielectric,” Surface and Coatings Technology, vol. 300, pp. 50–57, 2016. View at Publisher · View at Google Scholar · View at Scopus
  167. L. Li, L. Zhao, Z. Y. Li, L. Feng, and X. Bai, “Surface characteristics of Ti-6Al-4V by SiC abrasive-mixed EDM with magnetic stirring,” Materials and Manufacturing Processes, vol. 32, no. 1, pp. 83–86, 2017. View at Publisher · View at Google Scholar · View at Scopus
  168. B. Kuriachen and J. Mathew, “Effect of Powder Mixed Dielectric on Material Removal and Surface Modification in Microelectric Discharge Machining of Ti-6Al-4V,” Materials and Manufacturing Processes, vol. 31, no. 4, pp. 439–446, 2016. View at Publisher · View at Google Scholar · View at Scopus