Table of Contents Author Guidelines Submit a Manuscript
Advances in Materials Science and Engineering
Volume 2018, Article ID 2635084, 9 pages
https://doi.org/10.1155/2018/2635084
Research Article

Optimization of Process Parameters for Vertical-Faced Polypropylene Bottle Injection Molding

School of Mechanical and Automotive Engineering, Anhui Polytechnic University, Wuhu, China

Correspondence should be addressed to Zhichao Yan; moc.qq@2188708411

Received 3 March 2018; Revised 22 April 2018; Accepted 30 April 2018; Published 3 June 2018

Academic Editor: Marco Cannas

Copyright © 2018 Youmin Wang et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. C. Jiang-dong and L. Li-xin, “Optimum design of injection mold for hair dryer shell based on moldflow,” Plastic, vol. 39, pp. 122–125, 2010. View at Google Scholar
  2. S. Ke, H. Qing-chun, and J. Xiao-ping, “Optimization design of injection mold cooling channels arrangement,” Plastics Industry, vol. 40, pp. 25-26, 2014. View at Google Scholar
  3. W. Zili, Z. Shuyou, and Q. Lemiao, “Optimization method for process parameters coupling design oriented to green injection molding,” Computer Integrated Computing System, vol. 12, pp. 48–50, 2015. View at Google Scholar
  4. C. Wei-qing, W. Sheng-kai, and R. Wei, “Optimized design of printer on the cover of injection mold based on moldflow,” Plastic, vol. 16, pp. 101-102, 2012. View at Google Scholar
  5. C. Jin, T. Jianrong, and Y. Jiahong, “Multi-objective robust optimization of injection molding process parameters based on TOPSIS,” Journal of Mechanical Engineering, vol. 27, pp. 39-40, 2011. View at Google Scholar
  6. W. Bo, S. Wenxue, L. Qingtao, and D. Haiping, “Optimization of injection process parameters for thin walled plastic parts of battery cover based on orthogonal experiment,” Light Industry Machinery, vol. 4, pp. 50-51, 2014. View at Google Scholar
  7. H. Fengli, L. Ianping, Z. Meipeng, and X. Jinhong, Multi-Objective Robust Design and Optimum Algorithm in Injection Molding Process, Journal of Tongji University, Shanghai, China, 2011.
  8. H. Zhang, “Structural design of mouse injection mold,” Mechanical Research and Application, vol. 2, pp. 76-77, 2010. View at Google Scholar
  9. X. Zheng, B. Meng, and H. huang, “Design of injection mould for rear door handle based on CAE analysis,” Die industry, vol. 10, pp. 43–46, 2010. View at Google Scholar
  10. L. Qiong, A Practical Guide to Plastic Injection Moldflow, Mechanical Industry Press, Beijing, China, 2008.
  11. H. Ming-Shyan and C. Chin-Feng, “Injection molding and injection compression molding of thin-walled light-guided plates with V-grooved microfeatures,” Applied Polymer Science, vol. 12, pp. 1151–1159, 2011. View at Google Scholar
  12. Q. Huachang, Plastic Forming Process and Mold Design, Higher Education Press, Beijing, China, 2006.
  13. H. Jianming, “Improvement of air trap defects of power buttons based on flow simulation of moldflow,” China Plastics, vol. 7, pp. 60-61, 2013. View at Google Scholar
  14. W. Guilong, Z. Guoqun, L. Huiping, G. Yanjin, and C. Liang, “Heat response simulation of variotherm injection molding and optimization of mold structure,” Journal of Mechanical Engineering, vol. 2, pp. 18–20, 2009. View at Google Scholar
  15. C. Sheng-rong, X. Yong, Y. Guo-tai, and H. Cheng-hong, Research methods of parametric optimization for injection molding, China Plactics, vol. 4, 2003.
  16. F. Daver and B. Demirel, “A simulation study of the effect of preform cooling time in injection stretch blow molding,” Journal of Materials Processing Technology, vol. 11, 2012. View at Google Scholar
  17. B. Demirel and F. Daver, “Experimental study of preform reheat temperature in two-stage injection stretch blow molding,” Polymer Engineering & Science, vol. 4, 2013. View at Google Scholar
  18. B. Demirel and F. Daver, “Effects of preform deformation behavior on the properties of the poly(ethylene terephthalate) bottles,” Journal of Applied Polymer Science, vol. 4, 2012. View at Google Scholar
  19. R. A. Tatara, R. M. Sievers, and V. Hierzer, “Modeling the injection molding processing of a polypropylene closure having an integral hinge,” Journal of Materials Processing Technology, vol. 1, 2006. View at Google Scholar
  20. L. Rongliang and H. Zehao, “Study on Multi-objective Optimization of Injection Parameters for Shell Product Based on CAE,” Plastics Science and Technology, vol. 6, 2014. View at Google Scholar