Table of Contents Author Guidelines Submit a Manuscript
Advances in Materials Science and Engineering
Volume 2018, Article ID 3296398, 11 pages
https://doi.org/10.1155/2018/3296398
Research Article

Wear and Friction Evaluation of Different Tool Steels for Hot Stamping

1Metallurgy Research Centre IK4 AZTERLAN, Aliendalde Auzunea 6, 48200 Durango, Spain
2Department of Mechanical Engineering, University of the Basque Country (UPV/EHU), Plaza Ingeniero Torres Quevedo 1, 48013 Bilbao, Spain

Correspondence should be addressed to Carlos Angulo; se.uhe@olugna.solrac

Received 6 November 2017; Revised 12 February 2018; Accepted 22 February 2018; Published 26 March 2018

Academic Editor: Akihiko Kimura

Copyright © 2018 Maider Muro et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. Ö. N. Cora, K. Namiki, and M. Koc, “Wear performance assessment of alternative stamping die materials utilizing a novel test system,” Wear, vol. 267, no. 5–8, pp. 1123–1129, 2009. View at Publisher · View at Google Scholar · View at Scopus
  2. J. Hardell and B. Prakash, “High-temperature friction and wear behaviour of different tool steels during sliding against Al–Si-coated high-strength steel,” Tribology International, vol. 41, no. 7, pp. 663–671, 2008. View at Publisher · View at Google Scholar · View at Scopus
  3. J. Hardell, S. Hernandez, S. Mozgovoy, L. Pelcastre, C. Courbon, and B. Prakash, “Effect of oxide layers and near surface transformations on friction and wear during tool steel and boron steel interaction at high temperatures,” Wear, vol. 330–331, pp. 223–229, 2015. View at Publisher · View at Google Scholar · View at Scopus
  4. C. Boher, S. Le Roux, L. Penazzi, and C. Dessain, “Experimental investigation of the tribological behavior and wear mechanisms of tool steel grades in hot stamping of a high-strength boron steel,” Wear, vol. 294-295, pp. 286–295, 2012. View at Publisher · View at Google Scholar · View at Scopus
  5. A. Ghiotti, F. Sgarabotto, and S. Bruschi, “A novel approach to wear testing in hot stamping of high strength boron steel sheets,” Wear, vol. 302, no. 1-2, pp. 1319–1326, 2013. View at Publisher · View at Google Scholar · View at Scopus
  6. L. Deng, S. Mozgovoy, J. Hardell, B. Prakash, and M. Oldenburg, “Press-hardening thermo- mechanical conditions in the contact between blank and tool,” in Proceedings of 4th International Conference on Hot Sheet Metal Forming of High-Performance Steel (CHS2), pp. 293–300, Luleå, Sweden, June 2013.
  7. A. Ghiotti, S. Bruschi, and F. Borsetto, “Tribological characteristics of high strength steel sheets under hot stamping conditions,” Journal of Materials Processing Technology, vol. 211, no. 11, pp. 1694–1700, 2011. View at Publisher · View at Google Scholar · View at Scopus
  8. G. A. Fontalvo and C. Mitterer, “The effect of oxide-forming alloying elements on the high temperature wear of a hot work steel,” Wear, vol. 258, no. 10, pp. 1491–1499, 2005. View at Publisher · View at Google Scholar · View at Scopus
  9. L. Pelcastre, J. Hardell, and B. Prakash, “Galling mechanisms during interaction of tool steel and Al–Si coated ultra-high strength steel at elevated temperature,” Tribology International, vol. 67, pp. 263–271, 2013. View at Publisher · View at Google Scholar · View at Scopus
  10. K. Dohda, C. Boher, F. Rezai-Aria, and N. Mahayotsanun, “Tribology in metal forming at elevated temperatures,” Friction, vol. 3, no. 1, pp. 1–27, 2015. View at Publisher · View at Google Scholar · View at Scopus
  11. G. A. Fontalvo, R. Humer, C. Mitterer, K. Sammt, and I. Schemmel, “Microstructural aspects determining the adhesive wear of tool steels,” Wear, vol. 260, no. 9-10, pp. 1028–1034, 2006. View at Publisher · View at Google Scholar · View at Scopus
  12. I. Hussainova, E. Hamed, and I. Jasiuk, “Nanoindentation testing and modeling of chromium-carbide-based composites,” Mechanics of Composite Materials, vol. 46, no. 6, pp. 667–678, 2011. View at Publisher · View at Google Scholar · View at Scopus
  13. Y. Z. Liu, Y. H. Jiang, J. Feng, and R. Zhou, “Elasticity, electronic properties and hardness of MoC investigated by first principles calculations,” Physica B: Condensed Matter, vol. 419, pp. 45–50, 2013. View at Publisher · View at Google Scholar · View at Scopus
  14. L. Wu, T. Yao, Y. Wang, J. Zhang, F. Xiao, and B. Liao, “Understanding the mechanical properties of vanadium carbides: nano-indentation measurement and first-principles calculations,” Journal of Alloys and Compounds, vol. 548, pp. 60–64, 2013. View at Publisher · View at Google Scholar · View at Scopus