Table of Contents
International Journal of Manufacturing Engineering
Volume 2014, Article ID 208293, 12 pages
http://dx.doi.org/10.1155/2014/208293
Research Article

Observation of Drilling Burr and Finding out the Condition for Minimum Burr Formation

Department of Mechanical Engineering, Kalyani Government Engineering College, Kalyani, West Bengal 741235, India

Received 14 November 2013; Revised 30 January 2014; Accepted 13 February 2014; Published 24 March 2014

Academic Editor: Godfrey Onwubolu

Copyright © 2014 Nripen Mondal et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. L. K. Gillespie, “Burrs produced by drilling,” Tech. Rep. BDX-613-1248, Bendix Corporation, 1975. View at Google Scholar
  2. L. K. Gillespie and P. T. Blotter, “The formation and properties of machining burrs,” Journal of Engineering for Industry, Transactions of the ASME, vol. 98, no. 1, pp. 66–74, 1976. View at Google Scholar · View at Scopus
  3. K. Nakayama and M. Arai, “Burr formation in metal cutting,” CIRP Annals, Manufacturing Technology, vol. 36, no. 1, pp. 33–36, 1987. View at Publisher · View at Google Scholar · View at Scopus
  4. I. W. Park and D. A. Dornfeld, “A study of burr formation mechanism,” Journal of Engineering Materials and Technology, Transactions of the ASME, vol. 133, pp. 75–87, 1991. View at Google Scholar
  5. G.-L. Chern and D. A. Dornfeld, “Burr/breakout model development and experimental verification,” Journal of Engineering Materials and Technology, Transactions of the ASME, vol. 118, no. 2, pp. 201–206, 1996. View at Google Scholar · View at Scopus
  6. S. Min, “Control chart of drilling exit burr in low carbon steel,” LMA Report AISI4118, 2001. View at Google Scholar
  7. J. Kim, S. Min, and D. A. Dornfeld, “Optimization and control of drilling burr formation of AISI 304L and AISI 4118 based on drilling burr control charts,” International Journal of Machine Tools and Manufacture, vol. 41, no. 7, pp. 923–936, 2001. View at Publisher · View at Google Scholar · View at Scopus
  8. K. Lee and D. A. Dornfeld, “Micro-burr formation and minimization through process control,” An e-Scholarship Respiratory, Barkeley, Calif, USA, University of California, 2004.
  9. Y. B. Guo and D. A. Dornfeld, “Finite element analysis of drilling burr minimization with a backup material,” Transactions of NAMRI/ SME, vol. 26, pp. 207–212, 1998. View at Google Scholar
  10. Y. B. Guo and D. A. Dornfeld, “Finite element modeling of burr formation process in drilling 304 stainless steel,” Journal of Manufacturing Science and Engineering, Transactions of the ASME, vol. 122, no. 4, pp. 612–619, 2000. View at Google Scholar · View at Scopus
  11. I. W. Park and D. A. Dornfeld, “A study of burr formation processes using the finite element method—part I,” Journal of Engineering Materials and Technology, Transactions of the ASME, vol. 122, no. 2, pp. 221–228, 2000. View at Google Scholar · View at Scopus
  12. D. A. Dornfeld, “Strategies for preventing and minimizing burr formation,” An e-Scholarship Respiratory, Berkeley, Calif, USA, University of California, 2000.
  13. J. C. Aurich, D. Dornfeld, P. J. Arrazola, V. Franke, L. Leitz, and S. Min, “Burrs-analysis, control and removal,” CIRP Annals, Manufacturing Technology, vol. 58, no. 2, pp. 519–542, 2009. View at Publisher · View at Google Scholar · View at Scopus
  14. R. Neugebauer, G. Schmidt, and M. Dix, “Size effects in drilling burr formation,” in Proceedings of the CIRP International Conference on Burrs, pp. 117–128, Kaiserslautern, Germany, 2009.
  15. S. Kundu, Experimental investigation on the effect of different drilling conditions on burr formation towards its minimization [Masters Dissertation], Kalyani Government, Engineering College, Kalyani, India, 2011.
  16. S.-L. Ko and J.-K. Lee, “Analysis of burr formation in drilling with a new-concept drill,” Journal of Materials Processing Technology, vol. 113, no. 1–3, pp. 392–398, 2001. View at Publisher · View at Google Scholar · View at Scopus
  17. B. Shyu, “Burr reduction by tool design,” LMA Research Reports, University of California, Berkeley, Calif, USA, 2001. View at Google Scholar
  18. S. L. Ko and J. E. Chang, “Development of drill geometry for burr minimization in drilling,” CIRP Annals, Manufacturing Technology, vol. 52, no. 1, pp. 45–48, 2003. View at Google Scholar · View at Scopus
  19. T.-R. Lin and R.-F. Shyu, “Improvement of tool life and exit burr using variable feeds when drilling stainless steel with coated drills,” International Journal of Advanced Manufacturing Technology, vol. 16, no. 5, pp. 308–313, 2000. View at Publisher · View at Google Scholar · View at Scopus
  20. S. Min, D. A. Dornfeld, and Y. Nakao, “Influence of exit surface angle on drilling burr formation,” Journal of Manufacturing Science and Engineering, Transactions of the ASME, vol. 125, no. 4, pp. 637–644, 2003. View at Publisher · View at Google Scholar · View at Scopus
  21. S. P. Pratim and S. Das, “Burr minimization in face milling: an edge bevelling approach,” Proceedings of the Institution of Mechanical Engineers B: Journal of Engineering Manufacture, vol. 225, no. 9, pp. 1528–1534, 2011. View at Publisher · View at Google Scholar · View at Scopus
  22. P. P. Saha and S. Das, “An investigation on the effect of machining parameters and exit edge beveling on burr formation in milling,” Journal of Mechatronics and Intelligent Manufacturing, vol. 2, no. 1/2, pp. 73–84, 2011. View at Google Scholar
  23. K. Roy, P. Mukherjee, and U. K. Hansda, “An experimental investigation on drilling burr formation,” in Proceedings of Poster Presentation of the 3rd International and 24th AIMTDR Conference, pp. 211–216, Visakhapatnam, India, 2010.
  24. S. Tripathi and D. A. Dornfeld, “Review of geometric solutions for milling burr prediction and minimization,” Proceedings of the Institution of Mechanical Engineers B: Journal of Engineering Manufacture, vol. 220, no. 4, pp. 459–466, 2006. View at Publisher · View at Google Scholar · View at Scopus
  25. K. H. Kim, C. H. Cho, S. Y. Jeon, K. Lee, and D. A. Dornfeld, “Drilling and deburring in a single process,” Proceedings of the Institution of Mechanical Engineers Part B: Journal of Engineering Manufacture, vol. 217, no. 9, pp. 1327–1331, 2003. View at Publisher · View at Google Scholar · View at Scopus
  26. J. Choi, “Formation of Burr when drilling multi-layer materials,” in Proceedings of the CODEF Annual Meeting, University of California, Berkeley, Calif, USA, 2003.
  27. L. K. Lauderbaugh Saunders and C. A. Mauch, “An exit burr model for drilling of metals,” Journal of Manufacturing Science and Engineering, Transactions of the ASME, vol. 123, no. 4, pp. 562–566, 2001. View at Google Scholar · View at Scopus
  28. J. Kim and D. A. Dornfeld, “Development of an analytical model for drilling burr formation in ductile materials,” Journal of Engineering Materials and Technology, Transactions of the ASME, vol. 124, no. 2, pp. 192–198, 2002. View at Publisher · View at Google Scholar · View at Scopus
  29. U. Heisel and M. Schaal, “Burr formation in short hole drilling with minimum quantity lubrication,” Production Engineering, vol. 3, no. 2, pp. 157–163, 2009. View at Publisher · View at Google Scholar · View at Scopus
  30. S. R. Karnik, V. Gaitonde, and J. P. Davim, “Integrating Taguchi principle with genetic algorithm to minimize burr size in drilling of AISI 316L stainless steel using an artificial neural network model,” Proceedings of the Institution of Mechanical Engineers B: Journal of Engineering Manufacture, vol. 221, no. 12, pp. 1695–1704, 2007. View at Publisher · View at Google Scholar · View at Scopus
  31. Y. Nakao and Y. Watanabe, “Measurements and evaluations of drilling burr profile,” Proceedings of the Institution of Mechanical Engineers B: Journal of Engineering Manufacture, vol. 220, no. 4, pp. 513–523, 2006. View at Publisher · View at Google Scholar · View at Scopus
  32. V. N. Gaitonde and S. R. Karnik, “Minimizing burr size in drilling using artificial neural network (ANN)-particle swarm optimization (PSO) approach,” Journal of Intelligent Manufacturing, vol. 23, pp. 1783–1793, 2012. View at Publisher · View at Google Scholar · View at Scopus
  33. R. P. Lippmann, “An introduction to computing with neural nets,” IEEE ASSP Magazine, vol. 4, no. 2, pp. 4–22, 1987. View at Publisher · View at Google Scholar · View at Scopus
  34. J.J. Moré, “The Levenberg-Marquardt algorithm: implementation and theory,” Numerical Analysis: Lecture Notes in Mathematics, vol. 630, pp. 105–116, 1978. View at Google Scholar