Suppression or elimination of burr formation at the exit edge of the workpiece during drilling is essential to make quality products. In this work, low alloy steel specimens have been drilled to observe burr height under different machining conditions. Taper shank, uncoated 14&#x2009;mm diameter HSS twist drills are used in these experiments. Dry environment is maintained in experiment set I. Water is applied as cutting fluid in experiment set II. In the next four sets of experiments, the effect of providing back-up support material and exit edge bevel is observed on formation of burr at the exit edge of specimens under dry and wet conditions.  It is revealed that an exit edge bevel of 31 degrees with water as the cutting fluid gives negligible burr at the exit edge of the drilled hole at certain machining conditions. Use of a back-up support can also reduce drill burr to a large extent. In this paper, artificial neural networks (ANN) are developed for modeling experimental results, and modeled values show close matching with the experimental results with small deviations.

Nripen Mondal

Biswajit Sing Sardar

Ranendra Nath Halder

Santanu Das

Observation of Drilling Burr and Finding out the Condition for Minimum Burr Formation

Austenitic stainless steel sheets have gathered wide acceptance in the fabrication of components, which require high temperature resistance and corrosion resistance, such as metal bellows used in expansion joints in aircraft, aerospace, and petroleum industry. In case of single pass welding of thinner sections of this alloy, Pulsed Current Microplasma Arc Welding (PCMPAW) was found beneficial due to its advantages over the conventional continuous current process. The quality of welded joint depends on the grain size, hardness, and ultimate tensile strength, which have to be properly controlled and optimized to ensure better economy and desirable mechanical characteristics of the weld. This paper highlights the development of empirical mathematical equations using multiple regression analysis, correlating various process parameters to grain size, and ultimate tensile strength in PCMPAW of AISI 304L sheets. The experiments were conducted based on a five-factor, five-level central composite rotatable design matrix. A genetic algorithm (GA) was developed to optimize the process parameters for achieving the desired grain size, hardness, and ultimate tensile strength.

Siva Prasad Kondapalli

Srinivasa Rao Chalamalasetti

Nageswara Rao Damera

Optimization of Fusion Zone Grain Size, Hardness, and Ultimate Tensile Strength of Pulsed Current Microplasma Arc Welded AISI 304L Sheets Using Genetic Algorithm

Engineering design optimization of mechanical structures is nowadays essential in the mechanical industry (automotive, aeronautics, etc.). To remain competitive in the globalized world, it is necessary to create and design structures that, in addition to complying specific mechanical performance, should be less expensive. Engineers must then design parts or assemblies that are a better compromise between mechanical and functional performance, weight, manufacturing costs, and so forth. In this context Additive Manufacturing (AM) process offers the possibility to avoid tools and manufacture directly the part. There are numerous technologies which are using different kind of material. For each of these, there are at least two materials: the production material and the support one. Support material is, in most cases, cleaned and becomes a manufacturing residue. Improving the material volume and the global mass of the product is an essential aim surrounding the integration of simulation in additive manufacturing process. Moreover, the layer-by-layer technology of additive manufacturing allows the design of innovative objects, and the use of topological optimization in this context can create a very interesting combination. The purpose of our paper is to present the knowledge management of an AM trade oriented tool which integrated the topological optimization of parts and internal patterns.

Nicolas Gardan

Knowledge Management for Topological Optimization Integration in Additive Manufacturing

There is a demand for mechanistic force model that can predict and simulate the broaching process. In this paper, an attempt has been made for mechanistic force modeling of the broaching operation and experimental corroboration with the simulated result. The stiffness and damping coefficients for dynamic model are computed from the natural frequency of the broaching system and actual damped natural frequency has been obtained experimentally. Experimental work has been carried to compute the dynamic model parameters such as mass, stiffness, and damping coefficients. The simulated dynamic forces are illustrated graphically and are closely in agreement with the results obtained through manual broaching process.

Raghavendra Kamath Cholpadi

Appu Kuttan

Mechanistic Force Modeling for Broaching Process

Shrinkage behavior is a crucial problem in manufacturing plastic molded gear. This is because it negatively affects the dimensional stability and accuracy of the involute profile, as well as the concentricity, roundness, tooth spacing uniformity, and size of the gear. By integrating the Taguchi robust design, Grey relational analysis, and principal component analysis, we investigated the dimensional stability related to the shrinkage of tooth thickness, addendum circle, and dedendum circle of molded gear via the optimization of processing parameters and glass fiber reinforcement. The results revealed that the optimal combination of the processing parameters of the molded gear to achieve minimum shrinkage is melt temperature of 260&#xB0;C, packing pressure of 60&#x25;, packing time of 5&#x2009;s, and cooling time of 30&#x2009;s. The melt temperature showed the highest comparability sequence among the four key process parameters examined, followed by packing pressure, cooling time, and packing time. Meanwhile, the presence of glass fibers induced higher deviations of tooth thickness, addendum circle, and dedendum circle than those of the unfilled polyamide 6 gears.

Nik Mizamzul Mehat

Shahrul Kamaruddin

Abdul Rahim Othman

Optimized Injection Molding of Unfilled and Glass Filled PA6 Gears

About this journal

Journal profile

Meet the editorial board

Editor spotlight

Find out more

This journal's articles appear in a wide range of abstracting and indexing databases, and are covered by numerous other services that aid discovery and access. Find out more about where and how the content of this journal is available.

Abstracting and Indexing

International Journal of Manufacturing Engineering - Table of contents 2014

International Journal of Manufacturing Engineering | Hindawi

title

International Journal of Manufacturing Engineering

https://images.hindawi.com/journals/ijme/ijme.banner.jpg

International Journal of Manufacturing Engineering