Table of Contents Author Guidelines Submit a Manuscript
International Journal of Rotating Machinery
Volume 2007, Article ID 27247, 11 pages
http://dx.doi.org/10.1155/2007/27247
Research Article

A Class of Methods for the Analysis of Blade Tip Timing Data from Bladed Assemblies Undergoing Simultaneous Resonances—Part I: Theoretical Development

1Experimental Vibrations, Rolls-Royce PLC, P.O. Box 31, Derby DE24 8DJ, UK
2School of Mechanical Aerospace and Civil Engineering, University of Manchester, Simon Building, Oxford Road, Manchester M13 9PL, UK

Received 6 March 2006; Revised 17 November 2006; Accepted 4 January 2007

Academic Editor: Eric Maslen

Copyright © 2007 J. Gallego-Garrido et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. I. Ye Zablotskiy and Yu. A. Korostelev, “Measurement of Turbine Blades with the ELURA Device,” 1970, Energomashinostroneniye, Nr. 2, February 1970, pp. 36--39, English version: U.S. Air Force Systems Command Foreign Technology Division, FTD-ID(RS)T-0861-78, June 1978, AD-A066122.
  2. S. Heath, T. Slater, L. Mansfield, and P. Loftus, “Turbomachinery blade tip-timing measurement techniques,” in Proceedings of Advisory Group for Aerospace Research and Development Conference, 90th Symposium on Advanced Non-Intrusive Instrumentation for Propulsion Engines, pp. 32-1–32-9, Brussels, Belgium, October 1997.
  3. M. Zielinski and G. Ziller, “Noncontact vibration measurements on compressor rotor blades,” Measurement Science and Technology, vol. 11, no. 7, pp. 847–856, 2000. View at Publisher · View at Google Scholar
  4. G. Dimitriadis, I. B. Carrington, J. R. Wright, and J. E. Cooper, “Blade-tip timing measurement of synchronous vibrations of rotating bladed assemblies,” Mechanical Systems and Signal Processing, vol. 16, no. 4, pp. 599–622, 2002. View at Publisher · View at Google Scholar
  5. I. B. Carrington, J. R. Wright, J. E. Cooper, and G. Dimitriadis, “A comparison of blade tip-timing data analysis methods,” Proceedings of the Institution of Mechanical Engineers—Part G: Journal of Aerospace Engineering, vol. 215, no. 5, pp. 301–312, 2001. View at Publisher · View at Google Scholar
  6. J. Gallego-Garrido, G. Dimitriadis, and J. R. Wright, “Development of a multiple modes simulator of rotating bladed assemblies for blade tip-timing data analysis,” in Proceedings of the 27th International Conference on Noise and Vibration Engineering (ISMA '02), pp. 1437–1446, Leuven, Belgium, September 2002.
  7. J. Gallego-Garrido and G. Dimitriadis, “Validating synchronous blade vibration amplitudes from blade tip-timing data analysis,” in Proceedings of the 8th International Conference on Vibrations in Rotating Machinery, vol. 2, pp. 205–214, Swansea, UK, September 2004.
  8. E. K. Armstrong and R. E. Stevenson, “Some practical aspects of compressor blade vibration,” The Journal of the Royal Aeronautical Society, vol. 64, no. 591, pp. 117–130, 1960.
  9. W. W. Robinson, “Overview of Pratt & Whitney NSMS,” in Proceedings of the 45th International Instrumentation Symposium, Albuquerque, NM, USA, May 1999.
  10. W. W. Robinson and R. S. Washburn, “A Real Time Non-Interference Stress Measurement System (NSMS) for Determining Aero Engine Blade Stresses,” Instruments Society of America, 1991, paper 91-103, pp. 793–811.
  11. H. T. Jones, “Development of advanced non-intrusive stress measurement processing techniques,” in Proceedings of the 6th National Turbine Engine High Cycle Fatigue Conference, Jacksonville, Fla, USA, May 2001.
  12. B. W. Hayes, S. Arnold, C. Vining, and R. Howard, “Application of generation 4 non-contact stress measurement systems on HFC demonstrator engines,” in Proceedings of the 9th National Turbine Engine High Cycle Fatigue Conference, Pinehurst, NC, USA, March 2004.
  13. S. L. Marple, Digital Spectral Analysis: With Applications, Prentice-Hall, Englewood Cliffs, NJ, USA, 1987.