Brief Overview on Nitinol as Biomaterial

Wadood, Abdul

doi:https://doi.org/10.1155/2016/4173138

Advances in Materials Science and Engineering

On this page

Abstract Introduction Conclusions Acknowledgments References Copyright Related Articles

Review Article | Open Access

Volume 2016 | Article ID 4173138 | https://doi.org/10.1155/2016/4173138

Brief Overview on Nitinol as Biomaterial

Abdul Wadood¹

Academic Editor: Patrice Berthod

Received05 Sept 2016

Accepted10 Oct 2016

Published06 Nov 2016

Abstract

Shape memory alloys remember their shape due to thermoelastic martensitic phase transformation. These alloys have advantages in terms of large recoverable strain and these alloys can exert continuous force during use. Equiatomic NiTi, also known as nitinol, has a great potential for use as a biomaterial as compared to other conventional materials due to its shape memory and superelastic properties. In this paper, an overview of recent research and development related to NiTi based shape memory alloys is presented. Applications and uses of NiTi based shape memory alloys as biomaterials are discussed. Biocompatibility issues of nitinol and researchers’ approach to overcome this problem are also briefly discussed.

1. Introduction

1.1. Biomaterial

Biomaterials are those materials that are used in the human body. Biomaterials should have two important properties: biofunctionality and biocompatibility [1]. Good biofunctionality means that the biomaterial can perform the required function when it is used as a biomaterial. Biocompatibility means that the material should not be toxic within the body. Because of these two rigorous properties required for the material to be used as a biomaterial, not all materials are suitable for biomedical applications. The use of biomaterials in the medical field is an area of great interest as average life has increased due to advances in the use of surgical instruments and the use of biomaterials [2]. In vivo testing is related to testing within a living organism and in vitro testing is related to testing in an artificial environment. There are many famous journals related to biomaterials, for example, Biomaterials, Acta Biomaterialia, Journal of the Mechanical Behavior of Biomedical Materials, and Journal of Biomaterials Applications.

1.2. Shape Memory Alloys

Shape memory alloys have the ability to recover their original shape [3, 4]. Shape memory alloys remember their original shape. Figure 1 shows the mechanism of shape memory effect. Details about this figure are also available in the current author’s Ph.D. thesis [5]. The mechanism of shape memory effect and change in lattice structure is also given in Figure 8 of [6]. Here, the parent austenite phase is stable above austenite finish temperature and transforms to diffusionless twinned oriented martensitic phase upon cooling to a temperature below the martensite finish temperature (). In this process, the macroscopic shape of the specimen remains the same as the diffusionless martensitic phase transformation is self-accommodating [7]; however, microscopic changes take place during phase transformation. For shape memory effect, the material in general is in martensitic state at test temperature. When we apply an external force, martensite changes to detwinned martensite. Upon removal of force, the material becomes in detwinned martensitic state. When we heat this material above the austenite finish temperature (), reverse transformation occurs from detwinned/deformation-induced martensite to parent phase and the original shape is recovered. This is the mechanism of shape memory effect (SME). In case of shape memory effect, heating above the austenite transformation temperatures is a must to recover the original shape [5, 8].

1.3. Superelasticity

Figure 2 shows the mechanism of superelasticity. In case of superelasticity, the test temperature in general is well above the austenite finish temperature or in between the austenite start () and austenite finish () temperatures and the material is in austenitic state at test temperature. When we apply force, this austenite transforms to stress induced martensite. However, this martensite is stable only under the application of stress, and when we remove the stress, the material reverts back to austenite. In case of superelasticity, heating is not required to recover the original shape as here martensite is stable only under the application of stress [3, 8, 9].

1.4. Transformation Temperatures and Their Importance

The most effective and widely used shape memory alloys are nitinol [3, 7–12], copper based shape memory alloys [13–15], and iron based shape memory alloys [16–18]. Applications of shape memory alloys depend upon their phase transformation temperatures. These transformation temperatures are martensite start temperature (), martensite finish temperature (), austenite start temperature (), and austenite finish temperature () [3]. Transformation temperatures of nitinol are well below or close to body temperature, which is why nitinol has a large number of applications as a biomaterial [19–21] compared to copper based and iron based shape memory alloys where transformation temperatures are well above the body temperature [13–18]. Copper based shape memory alloys are suitable for high temperature, ~473 K, applications; however, due to above-body-temperature transformation temperatures, these alloys are not suitable as a biomaterial [13–15]. There is a need for research on copper based shape memory alloys to decrease their transformation temperatures below body temperature so that these alloys can be used as a biomaterial. Transformation temperatures dictate the use of shape memory alloy. If austenite transformation temperatures are below the body (test) temperature, then the shape memory alloy can be used as a biomaterial due to its superelasticity, and if the test temperature is below the martensitic transformation temperatures, then shape memory alloy can be used as a biomaterial due to its shape memory effect [3, 22].

1.5. Nitinol

Nitinol is a family of titanium based intermetallic materials that contain nearly equal amount of nickel and titanium. Nitinol shows shape memory and superelastic properties due to thermoelastic martensitic transformation [3, 7, 12]. In near-equiatomic NiTi alloys, shape memory effect and superelasticity are due to thermoelastic martensitic transformation from parent austenite phase with B2 structure to the monoclinic (M) or rhombohedral (R) martensitic phase transformation [23–25]. Table 1 shows different phases of equiatomic NiTi shape memory alloy, crystal system, lattice parameters, and interaxial angles. NiTi shape memory alloys were discovered by William J. Buehler and his coworkers in 1963 in the Naval Ordnance Lab (NOL), which is why equiatomic NiTi shape memory alloy is more commonly known as “nitinol” where “niti” stands for nickel-titanium and “nol” stands for Naval Ordnance Lab (NOL) [10, 26].

Phase diagrams are very important in studying different alloy systems, composition and temperature dependent phases, and control of the microstructure [27]. Physical properties of materials are strongly correlated with compositions and phases. Equiatomic NiTi (50 atomic% Ni, 50 atomic% Ti) shape memory alloy is an ordered intermetallic compound [3, 28].

Partial phase diagram of NiTi system is given in Figure 3 [3]. B2 phase region is known to be very narrow at temperature below 923 K. It is generally accepted that B2 phase region is only between 50 and 50.5 atomic% nickel. If nickel content is higher than 50.5 atomic%, then the alloy will decompose during cooling below 973 K to TiNi and TiNi₃. Ti₃Ni₄ and Ti₂Ni₃ are intermediate phases formed during transformation. The central part of Figure 3 where TiNi transforms to monoclinic B19′ martensitic phase is important. For the titanium rich side, equilibrium phase is Ti₂Ni and TiNi [3, 5, 28].

Nitinol based devices have been used in humans since the mid-1970s. Nitinol is now being practically used for various applications, for example, automotive applications, aerospace applications, eyeglasses, window frames, pipe couplings, antennae for cellular phones, actuators, sensors, seismic resistance, damping capacity, shock absorbers, automatic gas line shut-off valves, and SMA spring in water mixers [1, 29–33]. Some researchers are also working to increase the transformation temperatures of NiTi shape memory alloys so that these alloys can be used for high temperature applications. There is a detailed review about high temperature shape memory alloys [34].

If NiTi alloy is constrained to shape change upon phase transformation, then 700 MPa stresses can be generated, which are too much as compared to shape memory polymers where the amount of stress is much smaller. Due to the possibility of large recoverable strain of about 8% without force generation and 700 MPa stress without recoverable strain, there is a high possibility to use NiTi shape memory alloy for the design of components with different strain outputs and different amounts of external work output [3].

2. Biomedical Applications of Nitinol

Biomedical applications of nitinol are related to transformation temperatures of nitinol that are close to body temperature (310 K). Due to thermoelastic martensitic phase transformation and reverse transformation to parent austenite upon heating (shape memory effect) or upon unloading (superelasticity), nitinol has a large number of biomedical applications [35, 36]. Another important property of nitinol is its low elastic modulus close to natural bone material and compressive strength higher than natural bone material which makes it an ideal material for biomedical implant applications [37, 38]. In the medical field, nitinol has many applications; for example, it can be used as guided wire and heart valve tool, can be used in joining of fractured bones, and can be used as stent, as a guided wire, and as an orthodontic wire or brace [3, 39]. Attachments to each tooth in front of the teeth are called brackets. When NiTi arch wires are attached to brackets, teeth can move in a controlled manner [3]. Pitting corrosion of nitinol is better than SS304 stainless steel in saliva solution [40]. In [41], effects of processing on the properties and biomedical applications of nitinol are discussed. Some of the biomedical applications of nitinol (e.g., orthodontic arch wire, guided wire, bone fixation, and stent) are shown in Figure 4.

(a)

(b)

(c)

(d)

2.1. Applications of Nitinol as Arch Wire

Nitinol has been used in the dental field as an orthodontic arch wire for more than 20 years. Nitinol uses superelasticity for its use as an arch wire. Nitinol can be used in orthodontics due to its large strain recovery capacity and due to the generation of stresses that are useful for the alignment of teeth in the orthodontic process. NiTi arch wire can generate continuous orthodontic force even with teeth movement as this wire will change its shape during teeth alignment [3]. Nitinol has better pitting resistance when used as orthodontic arch wire in saliva solution as compared to stainless steel [40]. During phase transformation, if shape memory alloys are being stopped to change their shape, then stresses as high as 700 MPa can be generated and these stresses are useful for aligning of teeth. Other applications of nitinol are in dental implants and as attachments for partial dentures where the mechanism of shape memory effect is used [3, 33, 42]. Corrosion resistance of nitinol is significantly lower in fluoridated saliva than in nonfluoridated saliva [40, 43].

2.2. Comparison of Nitinol with Stainless Steel Arch Wire

Stainless steel has high elastic modulus as compared to nitinol whose modulus is close to bone material [37, 38]. If stainless steel having high elastic modulus is used as arch wire, then effective strain range related to an optimal force zone will be very small. The nature of applied stress in optimal force zone is such that the teeth alignment will be most efficient and it will support the optimum biological response. Excess force zone exists above the optimal force zone where there is a high possibility of tissue damage. Suboptimal and subthreshold force zones exist below the optimal zone where teeth move less efficiently, and if forces become minimal, then teeth may even come to a complete standstill without any teeth alignment. For nitinol that has low elastic modulus, effective strain range is large with wider optimal force zone. Therefore, nitinol having low elastic modulus provides a greater range of activation and fewer adjustments will be required for arch wire to move the teeth to their final positions. Nitinol arch wires having low elastic modulus have been successfully used as orthodontic wires [3]. Pitting corrosion of nitinol is better than SS304 stainless steel in saliva solution [40, 43]. Comparative studies of properties of different shape memory alloys for actuator applications are given in [44].

2.3. Applications of Nitinol as Guided Wire and in Endoscopes

Figure 4 shows some of the biomedical applications of nitinol. Particularly, a biomaterial with low modulus of elasticity is required to be used as a guided wire. Guided wire is a thin metal wire. It is entered through a natural opening or small incisions. Using NiTi shape memory alloy, nitinol guided wire reduces the chance of injury [3, 45]. One of the most sophisticated medical applications of shape memory alloys is active endoscope. Endoscopes are used in the general areas of the medical industry. A significant improvement was made in the flexibility and control in endoscopes by the use of nitinol shape memory alloy [46–48].

2.4. Applications of Nitinol in Stent

Other biomedical applications of nitinol include blood clot filters and stents in cardiovascular treatments. These alloys change their shape upon phase transformation and so they can be used as blood clot filters and as stents in cardiovascular treatments [49–51].

2.5. Applications of Nitinol in Orthopedics

A NiTi shape memory alloy is also a good material for use in orthopedic surgery. NiTi shape memory alloys have been used for bone plates to determine and fix fracture spine in scoliosis device (e.g., in higher shoulder) operation. During the transition phase, if the shape memory alloy stops to change its shape, it can generate stresses up to 700 MPa and these stresses are useful to join broken bones. The elastic modulus of NiTi is too close to that of the bone material of the human body and can also be used as an implant [3, 32, 52, 53].

2.6. Applications of Nitinol in Artificial Organs

Nitinol has applications in artificial organs, artificial kidney, and artificial heart pump and as actuator in ureteral stenosis after kidney transplantation [3, 54]. These applications need high fatigue strength and demand for miniaturization; NiTi alloy can meet both needs [55, 56]. NiTi shape memory biomaterials similar to other titanium based shape memory alloys due to thermoelastic martensitic transformation have great recovery strain and better low stress high cycle fatigue life compared to other metallic biomaterials [57]. Micromachines and microrobots require a microactuator. Thin film shape memory alloy is one of the many candidate materials for microactuators [58, 59]. Due to the size effect, slow response of bulk shape memory alloy can be improved by thin film technology.

3. Biocompatibility Issues of Nitinol

Nickel is a toxic element and causes contact allergy. In Europe, about 20% of the female population is allergic to the use of nickel. [43]. For good biocompatibility, nitinol should have good corrosion resistance so the release of nickel should be minimum [1, 3, 42]. Different researchers have studied the corrosion behavior of NiTi at body temperature (303 K). Some studies have been carried out in saliva solution [60] and some studies are carried out in Hank’s solution [61]. In order to improve the biocompatibility of nitinol, the current author of this study has also studied the effect of partial substitution of nickel with silver on the biocompatibility and corrosion behavior of nitinol in saliva solution and at 303 K [62]. Authors of [63] proposed the artificial saliva after studying the corrosion behavior of different biomaterials in 25 males’ and 25 females’ saliva solution mixture. The current author also used this composition of artificial saliva solution [63] for in vitro biocompatibility and corrosion behavior of NiTi-Ag intermetallic shape memory material [62]. For orthodontic use, most of the studies used testing solution at pH of 7 (neutral) [40–42]; however, during daily life, pH usually ranges from 4 to 5.5 (acidic), and after a meal it even falls below this value. Corrosion resistance of nitinol decreases significantly with medium acidification. Toothpastes used for the cleaning of teeth contain up to 1% sodium fluoride (NaF) and/or Na₂FPO₄. It is also reported that the corrosion resistance of nitinol significantly reduces in fluoridated saliva solution [43].

The biomaterial, when implanted into the human body or as braces, experiences specific mechanical and electrochemical interactions with the environment. For this reason, biomaterials, for example, stainless steel, Co-Cr alloys, titanium alloys, and nitinol, should have properties to remain stable under such hostile environment [3]. It is reported that titanium and nickel are released from nitinol into the surrounding body environment due to interaction of the biomaterial with the surrounding environment [64]. Potential danger of nitinol is associated with the negative effects of the release of nickel ions into the human body [3, 65]. Nitinol has poor corrosion properties in halide containing environment [43]. Venugopalan and Trépanier [21] reported 13 μg/day on average nickel ions release from nitinol braces in saliva environment.

Biofilm formation due to interaction of bacteria with the biomaterial affects the biofunctionality of the biomaterial. Biofilm results in some infectious diseases and affects the implant life. Understanding and control of biofilm formation will improve the implant life and patient health [66]. Biofilm results in oxygen differential cell formation, and acid metabolic products accumulate near the implant surface which results in the acceleration of cathodic reaction. Biofilm contains 75–95% water and the remaining is microorganisms. Biofilms generally decrease the corrosion resistance of implant material and also change the mode of corrosion taking place on the implant surface [67].

Silver is famous for its bacteria killing properties and coatings having silver addition are good against a number of bacteria [68] and there are some reports about NiTi-Ag shape memory alloys [62, 69]. Researchers are working to improve the corrosion and biocompatibility of nitinol by three different ways: (1) addition of a third element in nitinol [34, 62, 69, 70], (2) thin films formation on the surface of nitinol [58, 71], and (3) nickel-free titanium based shape memory alloys [72–74].

Ma and Wu [75] reported that NiTiTa has better corrosion resistance as compared to nitinol. Wen et al. [76] found that partial substitution of Ti with Cu improved the corrosion properties of nitinol. Ag, Nb, Zr, Mo, and Ta are biocompatible and are nontoxic. These elements form a passive oxide layer that hinders the release of nickel into the body environment. Saliva is related to the mouth environment. Duffó and Quezada Castillo proposed a new artificial saliva solution [63]. Duffó and Quezada Castillo in their paper concluded that four different dental alloys tested in their proposed artificial saliva solution showed an electrochemical behavior similar to that obtained in natural saliva. Cioffi et al. [43] carried out an electrochemical release test of nickel-titanium orthodontic wires in artificial saliva and concluded that different phases and temperature influence the nickel release rate trends. The current author’s Ph.D. thesis work, completed in 2012 from Hosoda-Inamura Lab, Tokyo Institute of Technology, Japan, was related to nickel-free titanium based shape memory alloys for biomedical applications [77]. The current author has published a number of papers related to nickel-free titanium based shape memory alloys for biomedical and engineering applications in international journals [78–86]. During postdoctoral work from 2012 to 2014 in the High Temperature Materials Unit, National Institute for Materials Science (NIMS), Tsukuba, Japan, the current author’s research activities were related to TiPt and TiAu based intermetallics for high temperature applications and he has published papers in international journals [87–94].

3.1. Biocompatibility Aspects of Thin Films on Nitinol

Diamond-like carbon (DLC) film is famous for its biocompatibility and resistance to chemicals. DLC film coatings protect the biomaterial from degradation and improve the stability of biomaterials. Further research is in progress related to DLC films on orthodontic devices [71]. Yeung et al. [95] reported the effects of nitrogen plasma implantation on NiTi alloys and reported that TiN layer formed during nitrogen plasma implantation has better wear and corrosion properties. TiN layer also decreases the nickel ions release. Titanium-silver alloys coatings have higher corrosion resistance than pure titanium [96].

4. Nitinol and Stainless Steel as Biomaterial

As opposed to stainless steel and cobalt-chrome wires, nitinol wires, due to their superelastic properties, allow the dentist to apply light and continuous force to teeth, reducing the potential of patient discomfort, tissue hyalinization (i.e., condition of disrepair), and undermining resorption. Hence, the use of NiTi alloy is widespread, especially during the first course of orthodontic treatment, when teeth are strongly misaligned; in these conditions, NiTi is in plateau region (on average 1–8% strain) and releases constant loads [3]. The most recent development in applying shape memory materials for biomedical applications is given in [97].

In short, there are a large number of biomedical applications of nitinol [98, 99] and there is a good book on the biomedical applications of shape memory alloys by Yoneyama and Miyazaki [100]. Professor Miyazaki from the University of Tsukuba and Professor Hideki Hosoda from Tokyo Institute of Technology, Japan, are famous professors in the field of shape memory alloys.

5. Conclusions

Mechanisms of shape memory effect and superelasticity are presented in this paper. An overview of biomedical applications of nitinol and NiTi based shape memory alloys is briefly presented in this paper. Biocompatibility issues of nitinol and researchers approach to overcome this problem are also discussed in this paper. The author’s contribution to the field of titanium based shape memory alloy is also briefly presented in this paper.

Competing Interests

The author declares that there are no competing interests regarding the publication of this paper.

Acknowledgments

The author is thankful to Professor Dr. Hideki Hosoda, Professor Dr. Tomonari Inamura from TITECH, and Dr. Yoko Yamabe-Mitarai from High Temperature Materials Unit, NIMS, Japan, for their continuous technical and moral support and guidance. The author is also thankful to Professor Dr. Ibrahim Qazi, Head of the Department (HOD), Department of Materials Science and Engineering, Institute of Space Technology, Islamabad, Pakistan, for his full technical and moral support. The author is also thankful to Higher Education Commission (HEC), Pakistan, for IPFP and NRPU research funding.

References

S. A. Shabalovskaya, “On the nature of the biocompatibility and on medical applications of NiTi shape memory and superelastic alloys,” Bio-Medical Materials and Engineering, vol. 6, no. 4, pp. 267–289, 1996.
View at: Google Scholar
A. Tathe, M. Ghodke, and A. P. Nikalje, “A brief review: biomaterials and their apllication,” International Journal of Pharmacy and Pharmaceutical Sciences, vol. 2, no. 4, pp. 19–23, 2010.
View at: Google Scholar
S. K. Otsuka and C. M. Wayman, Shape Memory Materials, Cambridge University Press, 1999.
W. M. Huang, Z. Ding, C. C. Wang, J. Wei, Y. Zhao, and H. Purnawali, “Shape memory materials,” Materials Today, vol. 13, no. 7-8, pp. 54–61, 2010.
View at: Publisher Site | Google Scholar
A. Wadood, Hosoda-inamura lab, Tokyo institute of technology, study on mechanical, shape memory and pseudo elastic properties of Ti-Cr-Sn and Ti-Cr-Ag alloys with various ageing treatments [Ph.D. thesis], 2012.
L. Sun, W. M. Huang, Z. Ding et al., “Stimulus-responsive shape memory materials: a review,” Materials & Design, vol. 33, no. 1, pp. 577–640, 2012.
View at: Publisher Site | Google Scholar
D. A. Porter and K. E. Easterling, Easterling, Phase Transformations in Metals and Alloys, 2nd edition, 1992.
M. Lai, Y. Gao, B. Yuan, and M. Zhu, “Remarkable superelasticity of sintered Ti–Nb alloys by Ms adjustment via oxygen regulation,” Materials and Design, vol. 87, pp. 466–472, 2015.
View at: Publisher Site | Google Scholar
M. J. Mahtabi and N. Shamsaei, “Multiaxial fatigue modeling for Nitinol shape memory alloys under in-phase loading,” Journal of the Mechanical Behavior of Biomedical Materials, vol. 55, pp. 236–249, 2015.
View at: Publisher Site | Google Scholar
D. Stoeckel, “The shape memory effect—phenomenon, alloys and applications,” in Proceedings: Shape Memory Alloys for Powern Systems EPRI, pp. 1–13, NDC-Nitinol Devices & Components, Fremont, Calif, USA, 1995.
View at: Google Scholar
H. Yin, Y. He, Z. Moumni, and Q. Sun, “Effects of grain size on tensile fatigue life of nanostructured NiTi shape memory alloy,” International Journal of Fatigue, vol. 88, pp. 166–177, 2016.
View at: Publisher Site | Google Scholar
A. Saigal and M. Fonte, “Solid, shape recovered bulk Nitinol—part I: tension-compression asymmetry,” Materials Science and Engineering A, vol. 528, no. 16-17, pp. 5536–5550, 2011.
View at: Publisher Site | Google Scholar
R. D. Dar, H. Yan, and Y. Chen, “Grain boundary engineering of Co–Ni–Al, Cu–Zn–Al, and Cu–Al–Ni shape memory alloys by intergranular precipitation of a ductile solid solution phase,” Scripta Materialia, vol. 115, pp. 113–117, 2016.
View at: Publisher Site | Google Scholar
A. O. Moghaddam, M. Ketabchi, and R. Bahrami, “Kinetic grain growth, shape memory and corrosion behavior of two Cu-based shape memory alloys after thermomechanical treatment,” Transactions of Nonferrous Metals Society of China, vol. 23, no. 10, pp. 2896–2904, 2013.
View at: Publisher Site | Google Scholar
Q. Yang, S. L. Wang, J. Chen, T. N. Zhou, H. B. Peng, and Y. H. Wen, “Strong heating rate-dependent deterioration of shape memory effect in up/step quenched Cu-based alloys: a ductile Cu-Al-Mn alloy as an example,” Acta Materialia, vol. 111, pp. 348–356, 2016.
View at: Publisher Site | Google Scholar
A. Cladera, B. Weber, C. Leinenbach, C. Czaderski, M. Shahverdi, and M. Motavalli, “Iron-based shape memory alloys for civil engineering structures: an overview,” Construction and Building Materials, vol. 63, pp. 281–293, 2014.
View at: Publisher Site | Google Scholar
R. A. Shakoor and F. A. Khalid, “Comparison of shape memory behavior and properties of iron-based shape memory alloys containing samarium addition,” Materials Science and Engineering A, vol. 457, no. 1-2, pp. 169–172, 2007.
View at: Publisher Site | Google Scholar
R. A. Shakoor, F. A. Khalid, and K. Kang, “Role of samarium additions on the shape memory behavior of iron based alloys,” Materials Science and Engineering A, vol. 528, no. 6, pp. 2299–2302, 2011.
View at: Publisher Site | Google Scholar
N. A. Obaisi, M. T. Galang-Boquiren, C. A. Evans et al., “Comparison of the transformation temperatures of heat-activated Nickel-Titanium orthodontic archwires by two different techniques,” Dental Materials, vol. 32, no. 7, pp. 879–888, 2016.
View at: Publisher Site | Google Scholar
S. A. Shabalovskaya, “Physicochemical and biological aspects of nitinol as a biomaterial,” International Materials Reviews, vol. 46, no. 5, pp. 233–250, 2001.
View at: Publisher Site | Google Scholar
R. Venugopalan and C. Trépanier, “Assessing the corrosion behaviour of Nitinol for minimally-invasive device design,” Minimally Invasive Therapy and Allied Technologies, vol. 9, no. 2, pp. 67–73, 2000.
View at: Publisher Site | Google Scholar
D. E. Hodgson, H. Ming, and R. J. Biermann, “Shape memory alloys, ASM Handbook,” in Properties and Selection: Nonferrous Alloys and Special-Purpose Materials, vol. 2 of ASM Handbook Committee, pp. 897–902, ASM International, 1990.
View at: Google Scholar
X. Wang, B. Verlinden, and J. Van Humbeeck, “Effect of post-deformation annealing on the R-phase transformation temperatures in NiTi shape memory alloys,” Intermetallics, vol. 62, pp. 43–49, 2015.
View at: Publisher Site | Google Scholar
C. W. Chan, S. H. J. Chan, H. C. Man, and P. Ji, “1-D constitutive model for evolution of stress-induced R-phase and localized Lüders-like stress-induced martensitic transformation of super-elastic NiTi wires,” International Journal of Plasticity, vol. 32-33, pp. 85–105, 2012.
View at: Publisher Site | Google Scholar
E. Polatidis, N. Zotov, E. Bischoff, and E. J. Mittemeijer, “The effect of cyclic tensile loading on the stress-induced transformation mechanism in superelastic NiTi alloys: an in-situ X-ray diffraction study,” Scripta Materialia, vol. 100, pp. 59–62, 2015.
View at: Publisher Site | Google Scholar
G. B. Kauffman and I. Mayo, “The story of nitinol: the serendipitous discovery of the memory metal and its applications,” The Chemical Educator, vol. 2, no. 2, pp. 1–21, 1997.
View at: Publisher Site | Google Scholar
S. H. Avner, Introduction to Physical Metallurgy by, McGraw-Hill, New York, NY, USA, 2nd edition, 1974.
ASM Hand Book, vol. 9, Metallography and Microstructures, 2004.
S. A. Shabalovskaya, H. Tian, J. W. Anderegg, D. U. Schryvers, W. U. Carroll, and J. V. Humbeeck, “The influence of surface oxides on the distribution and release of nickel from Nitinol wires,” Biomaterials, vol. 30, no. 4, pp. 468–477, 2009.
View at: Publisher Site | Google Scholar
R. Venugopalan and C. Trépanier, “Assessing the corrosion behaviour of Nitinol for minimally-invasive device design,” Minimally Invasive Therapy & Allied Technologies, vol. 9, no. 2, pp. 67–73, 2000.
View at: Publisher Site | Google Scholar
S. Shabalovskaya, J. Anderegg, and J. Van Humbeeck, “Critical overview of Nitinol surfaces and their modifications for medical applications,” Acta Biomaterialia, vol. 4, no. 3, pp. 447–467, 2008.
View at: Publisher Site | Google Scholar
N. B. Morgan, “Medical shape memory alloy applications-the market and its products,” Materials Science and Engineering A, vol. 378, no. 1-2, pp. 16–23, 2004.
View at: Publisher Site | Google Scholar
T. Duerig, A. Pelton, and D. Stöckel, “An overview of nitinol medical applications,” Materials Science and Engineering A, vol. 273–275, pp. 149–160, 1999.
View at: Publisher Site | Google Scholar
J. Ma, I. Karaman, and R. D. Noebe, “High temperature shape memory alloys,” International Materials Reviews, vol. 55, no. 5, pp. 257–315, 2010.
View at: Publisher Site | Google Scholar
L. H. Yahia, F. Rayes, and A. O. Warrak, “13-Regulation, orthopedic, dental, endovascular and other applications of Ti-Ni shape memory alloys,” in Shape Memory Alloys for Biomedical Applications, pp. 306–326, Woodhead Publishing, 2009.
View at: Google Scholar
A. R. Pelton, D. Stockel, and T. W. Deering, “Medical uses of nitinol,” Materials Science Forum, vol. 327-328, pp. 63–70, 2000.
View at: Google Scholar
M. Niinomi, “Recent research and development in titanium alloys for biomedical applications and healthcare goods,” Science and Technology of Advanced Materials, vol. 4, no. 5, pp. 445–454, 2003.
View at: Publisher Site | Google Scholar
V. Brailovski, S. Prokoshkin, M. Gauthier et al., “Bulk and porous metastable beta Ti–Nb–Zr(Ta) alloys for biomedical applications,” Materials Science and Engineering: C, vol. 31, no. 3, pp. 643–657, 2011.
View at: Publisher Site | Google Scholar
R. C. L. Sachdeva, S. Miyazaki, and Z. H. Dughaish, “Nitinol as a biomedical material,” in Reference Module in Materials Science and Materials Engineering, pp. 1–13, 2016.
View at: Google Scholar
M. Mirjalili, M. Momeni, N. Ebrahimi, and M. H. Moayed, “Comparative study on corrosion behaviour of Nitinol and stainless steel orthodontic wires in simulated saliva solution in presence of fluoride ions,” Materials Science and Engineering C, vol. 33, no. 4, pp. 2084–2093, 2013.
View at: Publisher Site | Google Scholar
A. R. Pelton, J. DiCello, and S. Miyazaki, “Optimization of processing and properties of medical-grade nitinol wire,” in Proceedings of the International Conference on Shape Memory and Superelastic Technologies (SMST '00), S. Russell and A. Pelton, Eds., Fremont, Calif, USA, 2000.
View at: Google Scholar
S. A. Shabalovskaya, “Surface, corrosion and biocompatibility aspects of Nitinol as an implant material,” Bio-Medical Materials and Engineering, vol. 12, no. 1, pp. 69–109, 2002.
View at: Google Scholar
M. Cioffi, D. Gilliland, G. Ceccone, R. Chiesa, and A. Cigada, “Electrochemical release testing of nickel-titanium orthodontic wires in artificial saliva using thin layer activation,” Acta Biomaterialia, vol. 1, no. 6, pp. 717–724, 2005.
View at: Publisher Site | Google Scholar
W. Huang, “On the selection of shape memory alloys for actuators,” Materials and Design, vol. 23, no. 1, pp. 11–19, 2002.
View at: Publisher Site | Google Scholar
C. Breschan, R. Jost, M. Platzer, and R. Likar, “Nitinol mandril guide wire facilitates percutaneous subclavian vein cannulation in a very small preterm infant,” Paediatric Anaesthesia, vol. 16, no. 3, pp. 366–368, 2006.
View at: Publisher Site | Google Scholar
C. M. Schirmer and C. B. Heilman, “Complete endoscopic removal of colloid cyst using a nitinol basket retriever,” Neurosurgical Focus, vol. 30, article E8, 2011.
View at: Publisher Site | Google Scholar
P. P. Poncet, Applications of Superelastic Nitinol Tubing, MEMRY Corporation, Menlo Park, Calif, USA, 1994.
T. Smrkolj and D. Šalinović, “Endoscopic removal of a nitinol mesh stent from the ureteropelvic junction after 15 years,” Case Reports in Urology, vol. 2015, Article ID 273614, 5 pages, 2015.
View at: Publisher Site | Google Scholar
D. Stoeckel, A. Pelton, and T. Duerig, “Self-expanding Nitinol stents: material and design considerations,” European Radiology, vol. 14, no. 2, pp. 292–301, 2004.
View at: Publisher Site | Google Scholar
F. Nematzadeh and S. K. Sadrnezhaad, “Effects of material properties on mechanical performance of Nitinol stent designed for femoral artery: finite element analysis,” Scientia Iranica, vol. 19, no. 6, pp. 1564–1571, 2012.
View at: Publisher Site | Google Scholar
D. J. McGrath, B. O'Brien, M. Bruzzi, and P. E. McHugh, “Nitinol stent design—understanding axial buckling,” Journal of the Mechanical Behavior of Biomedical Materials, vol. 40, pp. 252–263, 2014.
View at: Publisher Site | Google Scholar
R. Pfeifer, C. W. Müller, C. Hurschler, S. Kaierle, V. Wesling, and H. Haferkamp, “Adaptable orthopedic shape memory implants,” Procedia CIRP, vol. 5, pp. 253–258, 2013.
View at: Publisher Site | Google Scholar
M. Geetha, A. K. Singh, R. Asokamani, and A. K. Gogia, “Ti based biomaterials, the ultimate choice for orthopaedic implants—a review,” Progress in Materials Science, vol. 54, no. 3, pp. 397–425, 2009.
View at: Publisher Site | Google Scholar
F. J. Burgos, G. Bueno, R. Gonzalez et al., “Endourologic implants to treat complex ureteral stenosis after kidney transplantation,” Transplantation Proceedings, vol. 41, no. 6, pp. 2427–2429, 2009.
View at: Publisher Site | Google Scholar
M. J. Mahtabi, N. Shamsaei, and M. R. Mitchell, “Fatigue of Nitinol: the state-of-the-art and ongoing challenges,” Journal of the Mechanical Behavior of Biomedical Materials, vol. 50, pp. 228–254, 2015.
View at: Publisher Site | Google Scholar
A. R. Pelton, V. Schroeder, M. R. Mitchell, X.-Y. Gong, M. Barney, and S. W. Robertson, “Fatigue and durability of Nitinol stents,” Journal of the Mechanical Behavior of Biomedical Materials, vol. 1, no. 2, pp. 153–164, 2008.
View at: Publisher Site | Google Scholar
S. J. Li, T. C. Cui, Y. L. Hao, and R. Yang, “Fatigue properties of a metastable β-type titanium alloy with reversible phase transformation,” Acta Biomaterialia, vol. 4, no. 2, pp. 305–317, 2008.
View at: Publisher Site | Google Scholar
M. Shayan and Y. Chun, “An overview of thin film nitinol endovascular devices,” Acta Biomaterialia, vol. 21, pp. 20–34, 2015.
View at: Publisher Site | Google Scholar
A. Peter Jardine, J. S. Madsen, and P. G. Mercado, “Characterization of the deposition and materials parameters of thin-film TiNi for microactuators and smart materials,” Materials Characterization, vol. 32, no. 3, pp. 169–178, 1994.
View at: Publisher Site | Google Scholar
K.-T. Oh, U.-H. Joo, G.-H. Park, C.-J. Hwang, and K.-N. Kim, “Effect of silver addition on the properties of nickel-titanium alloys for dental application,” Journal of Biomedical Materials Research—Part B Applied Biomaterials, vol. 76, no. 2, pp. 306–314, 2006.
View at: Publisher Site | Google Scholar
I. Milošev and B. Kapun, “The corrosion resistance of Nitinol alloy in simulated physiological solutions: part 1: the effect of surface preparation,” Materials Science and Engineering C, vol. 32, no. 5, pp. 1087–1096, 2012.
View at: Publisher Site | Google Scholar
A. Wadood, In vitro biocompatibility and corrosion behavior of NiTi based shape memory alloys [M.S. thesis], GIK Institute of Engineering, Sciences and Technology, Khyber Pakhtunkhwa, Pakistan, 2008.
G. S. Duffó and E. Quezada Castillo, “Development of an artificial saliva solution for studying the corrosion behavior of dental alloys,” Corrosion, vol. 60, no. 6, pp. 594–602, 2004.
View at: Publisher Site | Google Scholar
S. Shabalovskaya and J. Van Humbeeck, “Biocompatibility of Nitinol for biomedical applications,” in Shape Memory Alloys for Biomedical Applications, T. Yoneyama and S. Miyazaki, Eds., Woodhead Publishing Series in Biomaterials, chapter 9, pp. 194–233, 2009.
View at: Publisher Site | Google Scholar
Y. Oshida, R. Sachdeva, S. Miyazaki, and S. Fukuyo, “Biological and chemical evaluation of TiNi alloys,” Materials Science Forum, vol. 56–58, pp. 705–710, 1990.
View at: Publisher Site | Google Scholar
V. C. Dinca, S. Soare, A. Barbalat et al., “Nickel-titanium alloy: cytotoxicity evaluation on microorganism culture,” Applied Surface Science, vol. 252, no. 13, pp. 4619–4624, 2006.
View at: Publisher Site | Google Scholar
P. R. Roberge, Handbook of Corrosion Engineering 2000, McGraw-Hill Company, New York, NY, USA, 2000.
C. Zamponi, M. Wuttig, and E. Quandt, “Ni–Ti–Ag shape memory thin films,” Scripta Materialia, vol. 56, no. 12, pp. 1075–1077, 2007.
View at: Publisher Site | Google Scholar
S. Hao, L. Cui, J. Jiang et al., “A novel multifunctional NiTi/Ag hierarchical composite,” Scientific Reports, vol. 4, article 5267, 2014.
View at: Publisher Site | Google Scholar
J. J. Moore and R. C. Yi, “Combustion synthesis of Ni-Ti-X shape memory alloys,” MRS Proceedings, vol. 246, pp. 246–331, 1991.
View at: Publisher Site | Google Scholar
Y. Ohgoe, S. Kobayashi, K. Ozeki et al., “Reduction effect of nickel ion release on a diamond-like carbon film coated onto an orthodontic archwire,” Thin Solid Films, vol. 497, no. 1-2, pp. 218–222, 2006.
View at: Publisher Site | Google Scholar
S. Miyazaki, H. Y. Kim, and H. Hosoda, “Development and characterization of Ni-free Ti-base shape memory and superelastic alloys,” Materials Science and Engineering A, vol. 438–440, pp. 18–24, 2006.
View at: Publisher Site | Google Scholar
Y. Al-Zain, H. Y. Kim, H. Hosoda, T. H. Nam, and S. Miyazaki, “Shape memory properties of Ti-Nb-Mo biomedical alloys,” Acta Materialia, vol. 58, no. 12, pp. 4212–4223, 2010.
View at: Publisher Site | Google Scholar
Y. Kusano, T. Inamura, H. Hosoda, K. Wakashima, and S. Miyzaki, “Phase constitution and mechanical property of Ti-Cr and Ti-Cr-Sn alloys containing 3d transition metal elements,” Advanced Materials Research, vol. 89, pp. 307–312, 2010.
View at: Google Scholar
J. L. Ma and K. Wu, “The corrosion behavior of NiTi-Ta shape memory alloy,” in Proceedings of the International Conference on Shape Memory and Superelastic Technologies (SMST '00), pp. 291–298, Pacific Grove, Calif, USA, April-May 2000.
View at: Google Scholar
X. Wen, N. Zhang, X. Li, and Z. Cao, “Electrochemical and histomorphometric evaluation of the TiNiCu shape memory alloy,” Bio-Medical Materials and Engineering, vol. 7, no. 1, pp. 1–11, 1997.
View at: Google Scholar
A. Wadood, Study on mechanical, shape memory and pseudoelastic properties of Ti-Cr-Sn and Ti-Cr-Ag alloys with various ageing treatments [Ph.D. thesis], Tokyo Institute of Technology, Yokohama, Japan, 2012.
A. Wadood, T. Inamura, H. Hosoda, and S. Miyazaki, “Comparative study of Ti-xCr-3Sn alloys for biomedical applications,” Materials Transactions, vol. 52, no. 9, pp. 1787–1793, 2011.
View at: Publisher Site | Google Scholar
A. Wadood, T. Inamura, H. Hosoda, and S. Miyazaki, “Ageing behavior of Ti-6Cr-3Sn β titanium alloy,” Materials Science and Engineering A, vol. 530, no. 1, pp. 504–510, 2011.
View at: Publisher Site | Google Scholar
A. Wadood, T. Inamura, H. Hosoda, and S. Miyazaki, “Effect of α phase precipitation on martensitic transformation and mechanical properties of metastable β Ti-6Cr-3Sn biomedical alloy,” Journal of Alloys and Compounds, vol. 577, supplement 1, pp. S427–S430, 2013.
View at: Publisher Site | Google Scholar
A. Wadooda, T. Inamuraa, Y. Yamabe-Mitaraib, and H. Hosodaa, “Strengthening of β Ti-6Cr-3Sn alloy through β grain refinement, α phase precipitation and resulting effects on shape memory properties,” Materials Science and Engineering: A, vol. 559, pp. 829–835, 2013.
View at: Publisher Site | Google Scholar
A. Wadood, T. Inamura, Y. Yamabe-Mitarai, and H. Hosoda, “Comparison of bond order, metal d orbital energy level, mechanical and shape memory properties of Ti–Cr–Sn and Ti–Ag–Sn alloys,” Materials Transactions, vol. 54, no. 4, pp. 566–573, 2013.
View at: Publisher Site | Google Scholar
A. Wadood, T. Inamura, Y. Yamabe-Mitarai, and H. Hosoda, “Effect of uniform distribution of α phase on mechanical, shape memory and pseudoelastic properties of Ti-6Cr-3Sn alloy,” Materials Science and Engineering A, vol. 555, pp. 28–35, 2012.
View at: Publisher Site | Google Scholar
A. Wadood, T. Inamura, H. Hosoda, and S. Miyazaki, “Cold workability, mechanical properties, pseoudoelastic and shape memory response of silver added Ti-5Cr alloys,” Advanced Materials Research, vol. 409, pp. 639–644, 2012.
View at: Publisher Site | Google Scholar
A. Wadood, T. Inamura, H. Hosoda, and S. Miyazaki, “Effect of ageing on mechanical and shape memory properties of Ti-5Cr-4Ag alloy,” Key Engineering Materials, vol. 510-511, no. 1, pp. 111–117, 2012.
View at: Publisher Site | Google Scholar
A. Wadood, T. Inamura, H. Hosoda, and S. Miyazaki, “Comparative study of Ti-6Cr-3Sn biomedical alloy in solution-treated and 473K-aged conditions,” in Proceedings of the 12th World Conference on Titanium (Ti '11), vol. 3, pp. 2086–2089, Beijing, China, June 2011.
View at: Google Scholar
A. Wadood, M. Takahashi, S. Takahashi, H. Hosoda, and Y. Yamabe-Mitarai, “High-temperature mechanical and shape memory properties of TiPt-Zr and TiPt-Ru alloys,” Materials Science and Engineering A, vol. 564, pp. 34–41, 2013.
View at: Publisher Site | Google Scholar
A. Wadood and Y. Yamabe-Mitarai, “Silver- and Zirconium-added ternary and quaternary TiAu based high temperature shape memory alloys,” Journal of Alloys and Compounds, vol. 646, pp. 1172–1177, 2015.
View at: Publisher Site | Google Scholar
A. Wadood and Y. Yamabe-Mitarai, “Recent research and developments related to near-equiatomic titanium-platinum alloys for high-temperature applications,” Platinum Metals Review, vol. 58, no. 2, pp. 61–67, 2014.
View at: Publisher Site | Google Scholar
A. Wadood and Y. Yamabe-Mitarai, “TiPt-Co and TiPt-Ru high temperature shape memory alloys,” Materials Science and Engineering A, vol. 601, pp. 106–110, 2014.
View at: Publisher Site | Google Scholar
A. Wadood, H. Hosoda, and Y. Yamabe-Mitarai, “Phase transformation, oxidation and shape memory properties of Ti-50Au-10Zr alloy for high temperature applications,” Journal of Alloys and Compounds, vol. 595, pp. 200–205, 2014.
View at: Publisher Site | Google Scholar
Y. Yamabe-Mitaraia, R. Arockiakumara, A. Wadood et al., “Ti(Pt, Pd, Au) based high temperature shape memory alloys,” Materials Today: Proceedings, vol. 2S, pp. S517–S522, 2015.
View at: Google Scholar
A. Wadood, H. Hosoda, and Y. Yamabe-Mitarai, “TiAu based shape memory alloys for high temperature applications,” in Proceedings of the 13th International Symposium on Advanced Materials (ISAM '13), vol. 60, Islamabad, Pakistan, September 2013.
View at: Publisher Site | Google Scholar
Y. Yamabe-Mitarai, A. Wadood, R. Arockiakumar et al., “High-temperature shape memory alloys based on Ti-platinum group metals compounds,” Materials Science Forum, vol. 783-786, pp. 2541–2545, 2014.
View at: Publisher Site | Google Scholar
K. W. K. Yeung, R. W. Y. Poon, X. M. Liu et al., “Nitrogen plasma-implanted nickel titanium alloys for orthopedic use,” Surface and Coatings Technology, vol. 201, no. 9–11, pp. 5607–5612, 2007.
View at: Publisher Site | Google Scholar
K. T. Oh, H. M. Shim, and K. N. Kim, “Properties of titanium-silver alloys for dental application,” Journal of Biomedical Materials Research Part B: Applied Biomaterials, vol. 74, no. 1, pp. 649–658, 2005.
View at: Google Scholar
W. M. Huang, C. L. Song, Y. Q. Fu et al., “Shaping tissue with shape memory materials,” Advanced Drug Delivery Reviews, vol. 65, no. 4, pp. 515–535, 2013.
View at: Publisher Site | Google Scholar
J. M. Jani, M. Leary, A. Subic, and M. A. Gibson, “A review of shape memory alloy research, applications and opportunities,” Materials & Design, vol. 56, pp. 1078–1113, 2014.
View at: Publisher Site | Google Scholar
R. C. L. Sachdeva, S. Miyazaki, and Z. H. Dughaish, “Nitinol as a biomedical material,” in Encyclopedia of Materials: Science and Technology, pp. 6155–6160, 2nd edition, 2001.
View at: Google Scholar
T. Yoneyama and S. Miyazaki, Shape Memory Alloys for Biomedical Applications, Woodhead, 1st edition, 2008.

Copyright

Copyright © 2016 Abdul Wadood. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

23333

Downloads

5526

Citations