Abstract

The study examined the osmotic dehydration of pumpkin slices in chokeberry, flowering quince, and raspberry concentrated juices. Products obtained were subjected to vacuum-microwave finish drying (VMD). The objective of the study was to evaluate the drying kinetics and the chemical properties, that is, total polyphenolics content and antioxidant capacity of the vacuum-microwave-dried pumpkin products. The concentration and temperature of the juices were 40°Brix and 45°C, respectively. The pumpkin slices were pretreated in concentrated juices for 0.5, 1, 2, 3, and 6 hours. Vacuum-microwave finish drying was carried out at the power of magnetrons that ensured the maintenance of the safe temperature (below 90°C) of the slices measured with the use of infrared camera. The results of the study showed that the moisture content of samples during the pretreatment in concentrated juices was decreasing until the equilibrium stage. The logarithmic model was used to describe the drying kinetics of pumpkin during VMD. Osmotic pretreatment resulted in a decrease in colour coordinates, improved the antioxidant activity of dried product, and prolonged the duration of VMD.

1. Introduction

Drying is one of the most common technological operations used for prolongation of the shelf life of vegetables [1]. Pumpkin is a source of vitamins, especially ascorbic acid, riboflavin and tocopherols, carotenoids, and tannins and also minerals like magnesium, potassium, iron, phosphorus, and selenium [2]. Nevertheless, the antioxidant capacity of pumpkin flesh is relatively low. It can be improved by soaking raw materials in concentrated juices obtained from fruits containing relatively higher amounts of biologically active components. Chokeberry fruits are known as an excellent source of polyphenolic compounds [3]. On the other hand, flowering quince and raspberry fruits can be also considered due to their attractive flavour and colour [4]. Therefore, concentrated fruit juices seem to be appropriate agents for osmotic dehydration (OD) of plant materials.

During OD, three types of mass transfer occur with different intensity [5]. The first type is water flux from the raw material to the osmotic solution. The second type is the solids transfer from the solution to the raw material, while the third type consists of natural solutes migration from the raw material to the solution. The intensities of particular types of mass transfer depend on the temperature, concentration, and the kind of the osmotic solution [6]. Usually, sucrose is used to prepare an osmotic solution for dehydration of plant materials. OD in sucrose solution was applied to many raw materials such as pepper [7], strawberries [8], apples [9], or pumpkin [10]. However, osmotically predried raw material involves finish drying in order to reduce the moisture content until the safe level and to ensure the attractive texture of the final product. Among several methods used for this purpose, vacuum-microwave drying (VMD) seems to be appropriate. During VMD, the energy of microwaves is absorbed by water located in the whole volume of the material being dried. This creates a large vapour pressure in the centre of the material, allowing rapid transfer of moisture to the surrounding vacuum, which protects from the structural collapse [11]. As a consequence, the rate of drying is considerably higher than in traditional methods of dehydration [12]. The puffing phenomenon that accompanies the rapid process of dehydration creates a porous texture of the food and facilitates obtaining a crispy and delicate texture [13], and in this way it reduces the product’s density as well as its shrinkage.

Vacuum-microwave drying (VMD) technique has already been successfully applied to reduce the moisture content of plant materials, that is, carrots [11], cranberries [14], strawberries [15], bananas [16], apples [13], pumpkin [17], and garlic [18]. At the beginning of VMD, the intensive water evaporation from the material may exceed the capacity of a vacuum pump. This would require a reduction in the quantity of the material subjected to drying or application of a large vacuum installation. This problem can be overcome by predrying of the material using OD. As a result of predrying, the mass loads of VM equipment can be radically decreased [19]. Predrying of the material by convective method before vacuum-microwave finish drying (VMD) reduced the total cost of dehydration and improved the quality of dried tomatoes [20], strawberries [21], and beetroot cubes [22]. No scientific work has been yet reported on the drying of pumpkin by the combined method consisting of osmotic pretreatment and VMD. Furthermore, the use of concentrated fruit juices instead of sucrose as an osmotic agent may have also a healthy aspect. This method of drying could make a significant contribution to the vegetable processing industry. Therefore, the main aim of this study was to evaluate the possibility of using a combination of osmotic pretreatment in concentrated chokeberry, flowering quince, and raspberry juices and VMD for processing of pumpkin flesh. The effect of osmotic pretreatment on VMD kinetics, colour, polyphenols content, and antioxidant capacity of dried product was evaluated.

2. Materials and Methods

2.1. Materials

Pumpkin (Cucurbita maxima Duchesne cv. Hokkaido) was cultivated in a field located close to Wrocław (Poland). Pumpkin flesh (Mc = 6.72 kg·kg−1db) was cut into rectangular slices with dimensions of 20 × 10 × 5 mm.

2.2. Osmotic Solution

Commercial concentrated fruit juices (Rauch Polska, Płońsk, Poland, 65°Brix) were used in the study to prepare osmotic solutions with concentration of 40°Brix: (a) chokeberry juice, (b) flowering quince juice, and (c) raspberry juice. The concentrated juices were obtained only by water removal from the natural juices; there are no additives and no conservatives added. Physical and chemical properties of osmotic solutions are provided in Table 1. The concentration of juices was measured using Atago Digital Brix Refractometer (PAL-3, Atago Co., Ltd., Tokyo, Japan). The temperature of osmotic solution was 45°C [23].

2.3. Osmotic Dehydration (OD)

Osmotic solutions were placed in beakers immersed in the water bath at 45°C. The ratio of osmotic solution to pumpkin slices was maintained at 3 : 1 (180 ml : 60 g of fresh matter). The mass of the samples was measured after 0.5, 1, 2, 3, and 6 hours of OD. The samples were taken out from the solution by using a tea strainer and the surplus moisture was gently eliminated from their surfaces with a tissue paper before measuring their mass.

Determination of mass transfer during osmotic dehydration (OD) was shown as the solid gain (SG) and water loss (WL) calculated by equations presented by Nowicka et al. [24].

2.4. Vacuum-Microwave Drying (VMD)

VMD was performed in SM 200 dryer (Plazmatronika, Wrocław, Poland) [25]. Drying was carried out with wattage adjustment involving a reduction of microwave power from initial 480 W to 120 W to avoid overheating of the dried material. Temperature of the samples was measured by infrared camera Flir i50 (FLIR Systems AB, Sweden).

2.5. Moisture Content

The moisture content was determined using a vacuum-dryer (SPT-200; ZEAMiL Horyzont, Kraków, Poland), where samples were kept at 70°C at the pressure of 100 Pa for 24 h.

2.6. Drying Kinetics

The drying kinetics were determined on the basis of the mass losses of the pumpkin samples. During VMD, samples were weighed every 2 and 8 min for 480 W and 120 W, respectively, in order to get a similar energy input between the mass measurements regardless of the microwave power level. This procedure enabled obtaining similar number of measuring points for particular samples which were dried using different microwave power levels (480 W or 120 W). The drying kinetics represent decreasing of moisture ratio (MR) in time of drying. MR was determined using the following equation [25]:where is the actual moisture content and is the initial moisture content.

Preliminary tests conducted in this study proved that the best fitting was obtained for the logarithmic model (see (2)); consequently, only this model was used in this study, where , , and are constants.

2.7. Colour Measurement

Colour of dried samples was measured using Minolta Chroma Meter CR-400 (Minolta Co. Ltd., Osaka, Japan). Instrumental colour data were provided as CIE , , and coordinates, which define the colour in a three-dimensional space. The total change in the colour (dE) during the VMD was calculated according to Sledz et al. [26] between dried pumpkin and fresh pumpkin.

2.8. Total Phenolics and Antioxidant Activity

Total phenolics content was measured with application of the Folin-Ciocalteu reagent with gallic acid (GA) as a standard according to Gao et al. [27]. All determinations were performed in triplicate.

The antioxidant activity of extracts was determined using the FRAP assay according to Benzie and Strain [28]. Antioxidant capacity was also determined by ABTS method, according to Re et al. [29]. Determinations by ABTS and FRAP methods were performed using a UV-2401 PC spectrophotometer (Shimadzu, Kyoto, Japan). All determinations were performed in triplicate.

2.9. Viscosity of Osmotic Solutions

Viscosity of osmotic solutions was determined using a Vibro Viscometer SV-10 (A&D Company, Limited, Tokyo, Japan). Temperature of osmotic solution was 45°C. The measurements were performed in triplicate.

2.10. Water Activity of Osmotic Solutions

Water activity was measured using water activity meter AquaLab Dew Point 4TE (Decagon Devices Inc., United States) at 25°C ± 0.5. The measurements were performed in triplicate.

2.11. Statistical Analysis

The results obtained were evaluated by statistical analysis with the use of the STATISTICA v. 12.0 (StatSoft, Inc., Tulsa, USA). Homogeneous groups were determined with Tukey’s HSD test at significance level of α = 0.05. TableCurve 2D V5.01 (Systat Software, San Jose, California, USA) enabled prediction of moisture ratio (MR) by fitting the mathematical model to experimental points with the highest possible values of the determination coefficient and the lowest values of root mean square error (RMSE) [25].

3. Results and Discussion

3.1. Osmotic Dehydration

Figure 1 shows water loss (WL) and solid gain (SG) during dehydration of pumpkin in concentrated juices prepared from chokeberry, flowering quince, and raspberry fruits. At the beginning of the process, the mass exchange between the pumpkin and concentrates was intensive and after 1 h, the mass exchange rate decreased. The values of water loss were almost 3 times higher than those obtained for the solid gain, regardless of the juice applied for the dehydration. A similar observation was made during osmotic dehydration of pumpkin in sucrose solution [30] and cherries in apple juice [24]. In the current study, the highest WL value was noticed during dehydration in concentrated flowering quince, whereas the lowest value was indicated during dehydration in concentrated chokeberry juice. This might result from different physical properties of osmotic solutions, that is, the value of water activity of flowering quince was = 0.9381, whereas of chokeberry solution was 0.9449 (Table 1). It was observed that the lower the water activity, the greater the osmotic pressure influencing the intensity of the mass exchange [6]. The value of SG was higher for flowering quince and chokeberry than for raspberry solution. This may be due to the viscosity of these solutions, which was the highest for raspberry concentrated juice (Table 1). The viscosity of the juice affects the penetration of solids from the solution to the material. An increasing viscosity of the solution results in an agglomeration of the particles. The agglomerated products might block transfer of particles into intracellular spaces [31]. After the OD process, the water content in the plant material is still relatively high; thus, to obtain more stable product, the further drying is required. Among several methods, VMD seems to be the most appropriate due to numerous advantages including shorter duration and higher efficiency of the process [32].

3.2. Vacuum-Microwave Drying (VMD)

The drying kinetics of raw pumpkin and pumpkin dehydrated in concentrated fruit juices are shown in Figures 24. Figure 2 represents VMD kinetics of fresh pumpkin (0 h) and pumpkin dehydrated in concentrated chokeberry juice for 0.5, 1, 2, 3, and 6 h. The duration of VMD of pumpkin was relatively short: 36 min (Table 2), whereas VMD of samples osmotically dehydrated in concentrated chokeberry juice was significantly longer, lasting up to 66 min, depending on the time of osmotic predehydration.

Such prolongation of drying time caused by osmotic pretreatment can be explained by a decrease of water diffusivity within the dried material enriched in water-binding substances absorbed from the concentrated juice. Another factor that prevents the removal of water from the dried material was the blockage of pores by the same substances, which additionally enhanced the increase in temperature of the sample during the VMD. The temperature of VMD material depends on the internal pressure of water vapour, which is closed in the plant cellular system [22]. Probably, the impregnation of cell walls which occurs during the osmotic dehydration process leads it to be less permeable to water vapour. This may explain both the higher temperature and lower drying rates when comparing the OD samples and raw material. A similar observation was made for VMD beetroots [25] and chokeberries [33] dehydrated in chokeberry juice. Similar results were obtained during drying of pumpkins dehydrated in concentrated flowering quince (Figure 3) and raspberry juice (Figure 4). In the case of pumpkin dehydrated in flowering quince concentrated juice, the time of VMD was slightly shorter (Table 2), since the fresh material lost a higher quantity of water in this osmotic solution. From this point of view, osmotic pretreatment in concentrated juices increases the energy consumption of the entire drying process. However, osmotic dehydration in concentrate solutions prepared from fruits with beneficial bioactive compounds can significantly increase the quality of dried material [4, 34].

The decrease of moisture ratio (MR) during the microwave-vacuum drying process was described by a logarithmic model (see (2)). Values of parameters and as well as the drying constant are presented in Table 2. Parameter describes the MR value at the beginning of the drying process ( = 0 min) and it is strongly correlated with the moisture content of the samples before the VMD, whereas parameter is the value of the asymptote function, which is strongly correlated with the final moisture content of the samples (). Drying constant () for pretreated samples was higher (0.183–0.240) than for samples dried without osmotic pretreatment (0.128). This was due to the fact that the amount of water in the dehydrated samples was lower and the time necessary for drying the raw material was longer. Values of determination coefficient for all tested samples were in the range from 0.9631 to 0.9914 (Table 1), while the values of root mean square error (RMSE) were below 0.129, indicating good fitting of mathematical functions to empirical points. Similar values of were obtained while describing a pumpkin drying process using a logarithmic model [35]. The final moisture content of the sample was between 6.7% and 11.4%, which guarantees stable products [36]. The maximum temperature of the samples obtained during the VMD depended on the duration of application of magnetron power of 480 W. It was assumed that when the temperature was around 80°C, the power would be reduced to 120 W. Table 2 shows the time of VMD when the power was reduced due to the temperature increase. The power reduction caused a significant reduction in the samples temperature (Figures 24). A similar relationship was obtained during VMD of cherries [37] and chokeberries [33].

3.3. Polyphenolics Content and Antioxidant Activity

The content of polyphenols (PC) and antioxidant capacity of fresh and dried samples are shown in Table 3. Similar values of PC and ABTS antioxidant activity for fresh pumpkin of Hokkaido variety were obtained by Obradović et al. [38]. For nonosmotically dehydrated pumpkin subjected to VMD process, a decrease in PC was observed after drying and the values of antioxidant capacity were reduced. During drying of biological materials, degradation of polyphenolic compounds occurs, which results in decreasing of antioxidant activity. This relationship was observed during drying of cherries [16], different cultivars of pumpkin [39], and blueberries [40]. The application of OD prior to VMD resulted in an increase in the content of polyphenol compounds, which significantly increased the antioxidant capacity of the dried product. OD performed by only 0.5 hours in the concentrated chokeberry juice caused a more than 5-fold increase in the content of polyphenolic compounds. A further OD process increased the content of these compounds, which after 6 h was more than 10 times greater than that in the fresh pumpkin. The increase in polyphenolic compounds was related to the penetration of solids from the osmotic solution to the dehydrated material. Similar results were observed during the dehydration of beetroots [25] and cherries [4] in concentrated chokeberry juice. Even greater increase in PC was obtained for pumpkin dehydrated in concentrated flowering quince juice. In the case of pumpkin samples dehydrated in raspberry juice, the increase was only over 2 times. Similar results were obtained for cherries dehydrated in concentrated flowering quince and raspberry juices [4]. It can be concluded that the dehydration in osmotic solutions improves the quality of the final products in terms of the content of biologically active components [41].

3.4. Colour Parameters

The colour parameters of fresh and dried samples were shown in Table 4. Colour measurement of fresh and dried pumpkin concerned the surface of the samples. The values of colour coordinates , , and determined for fresh pumpkin were used as a base for determination of . VMD resulted in a reduction of all colour parameters, which is typical for this method of drying [17]. Osmotic dehydration resulted in the change of dried pumpkin colour (), which ranged from 27.6 to 76.3 compared to the colour of fresh pumpkin. Such a large colour change was related to the colour of the fruit concentrates used for OD (Table 1). The substance from the osmotic solution, penetrating into the dehydrated material, changed the colour of the material [42]. The longer the dehydration time is, the more the colour parameters of the samples shift toward the colour parameters of the juice. The osmotic dehydration process in concentrated fruit juices can enhance the appearance of the dried fruit by concealing the unattractive natural discolouration of fruits and vegetables or colour alteration arises during harvesting, transport, and storage.

4. Conclusions

On the basis of the results obtained, it was concluded that the decrease in moisture ratio of the pumpkin slices during microwave-vacuum drying process could be described by a logarithmic model. The process of OD prolonged the time of microwave-vacuum finish drying and increased the temperature of samples during VMD due to the impregnation of wall cells by the substances absorbed from the concentrated juices. The absorption of these substances also decreased the values of colour parameters , , and and significantly increased the bioactivity of VMD pumpkin samples in terms of polyphenols content and antioxidant activity. The highest content of polyphenolic compounds and the stronger antioxidant capacity were noted when the flowering quince concentrated juice was used for the osmotic dehydration process due to the highest values of solid gain.

Conflicts of Interest

The authors declare that there are no conflicts of interest regarding the publication of this paper.

Acknowledgments

This work was funded by the science budget for the years 2010–2013 as Research Project no. N N312 338039 and by the National Science Centre (Poland) based on the Decision no. UMO-2014/15/D/NZ9/0524.