Optimization of Cultural Conditions for<i> Bacillus megaterium</i> Cultured in<i> Agaricus bisporus</i> Industrial Wastewater

Huang, Jiafu; Zhang, Danfeng; Ou, Yixin; Zhang, Guoguang; Zheng, Linhua; Lin, Lizhuan; Ye, Xiaomei; Zhu, Xiaofeng; Pan, Yutian

doi:https://doi.org/10.1155/2018/8106245

BioMed Research International

On this page

Abstract Introduction Materials and Methods Results and Discussion Data Availability Conflicts of Interest Acknowledgments References Copyright Related Articles

Research Article | Open Access

Volume 2018 | Article ID 8106245 | https://doi.org/10.1155/2018/8106245

Optimization of Cultural Conditions for Bacillus megaterium Cultured in Agaricus bisporus Industrial Wastewater

Jiafu Huang,^1,2Danfeng Zhang,^1,2Yixin Ou,^1,3Guoguang Zhang,^1,2Linhua Zheng,²Lizhuan Lin,²Xiaomei Ye,²Xiaofeng Zhu,²and Yutian Pan^1,2

Academic Editor: Paul M. Tulkens

Received07 Jun 2018

Revised01 Oct 2018

Accepted09 Dec 2018

Published26 Dec 2018

Abstract

The aim of this study was to optimize the cultural conditions for Bacillus megaterium using Agaricus bisporus industrial wastewater as nature culture through response surface methodology. In our present study, we analyzed the total number of living B. megaterium in the fermentation broth using multispectral imaging flow cytometry. Plackett-Burman design was applied to evaluate the effects of six variables, namely, initial pH, industrial wastewater solubility, rotating speed, culture temperature, inoculum size, and loading volume. Loading volume, initial pH, and culture temperature were found to influence the biomass of B. megaterium significantly and were further optimized by Box-Behnken design. After verification test, the optimum fermentation conditions of B. megaterium using the A. bisporus processing wastewater as nature culture media were obtained as follows: initial pH of 7.4, culture temperature of 25°C, loading volume of 40 mL/250 mL, culture time of 24 h, industrial wastewater solubility of 1%, rotating speed of 200 rpm, and inoculum size of 8%. The predicted optimum model’s value was 8.88 × 10⁸ Obj/mL and the average experimental value was 9.03 ± 0.02 × 10⁸ Obj/mL, which met the national microbial fertilizers’ standard. Furthermore, the field experiment results showed that the fermentation broth of B. megaterium could significantly improve the yield of Spinacia oleracea L.

1. Introduction

Along with the extensive use of fertilizers and pesticides in agricultural production, leading to serious ecological environment pollution and sharp fall of crop quality, microbial fertilizers more and more get people's attention. B. megaterium is a kind of plant growth promotion rhizobacteria and one common bacterium of microbial fertilizer, can degrade lecithin, organic phosphorus, and inorganic phosphorus in the soil to plants, can directly adsorb [1], can stimulate plant growth and alleviate phytotoxicity of pollutants [2–4], and also can improve soil fertility and crop disease resistance [5, 6].

A. bisporus is commonly known as the white button mushroom and is commonly referred to as a “mushroom”. It is one of the most economically important and widely produced mushrooms in the world. Mushrooms are primarily stored in cans and traded across the world. During the processes of the mushroom cans production, washing, preboiling, and canning, fresh mushrooms produce a large quantity of wastewater. The mushroom industrial wastewater has high BOD and COD content, of which the content of COD is 540.29 g/L, which is 13.07 times higher than the national three level emission standard [7]. The discharge of the wastewater into the surrounding areas is a cause of environmental pollution, so the wastewater discharged from mushroom processing industries has become a large burden to the environment. Developing methods for utilizing and disposing the mushroom processing wastewater is an important priority.

The wastewater from these processes contains a large amount of soluble components of the mushroom [7, 8]. Crude polysaccharides and 4 novel components (Abnp1001, Abnp1002, Abap1001, and Abap1002) were successfully obtained from the mushroom wastewater. The extraction of polysaccharides from the industrial mushroom wastewater yielded 3.30 g/g, 0.989 mg/g, 1.849 mg/g, 0.128 mg/g, and 0.68 mg/g, respectively. [7] There are 32.16% content of D-mannitol in the concentrated A. bisporus industrial wastewater [8]. And moreover, the test report of product of A. bisporus industrial wastewater in the processing enterprises (Fujian KEREN Biological Co., Ltd.) showed that there was 18.9% proteins in their product, which could provide sufficient carbon and nitrogen source for microbiological [9] and plants growth [10]. Now therefore, we attempt to search an optimal fermentation condition of B. megaterium fermented via shaking culture by using mushroom processing wastewater as a natural medium in our present study, which provided theoretical support for the development of the downstream industry of A. bisporus.

2. Materials and Methods

2.1. Strains and Growth Conditions

B. megaterium (GIM 1.270) was purchased from the Guangdong Culture Collection Center.

Seed medium is as follows: peptone 5 g, beef extract 3 g, NaCl 5 g, distilled water 1 L, pH 6.2, boiled and thawed, aliquoted and sterilized at 121°C for 15 min.

Preparation of seed suspension is as follows: B. megaterium which has been activated with vaccination loop was picked, with access to sterilized seed liquid medium containing 100 mL flask made of bacterial suspension, and placed in a shaker (30°C, 150 rpm) for 24 h.

Plackett-Burman design. Plackett-Burman design methods can be used in the screening of the key influential factors compared with other statistical designs on the experimental response [11]. Six variables (industrial wastewater solubility, initial pH, inoculum dose, loaded liquid, culture temperature, and shaking speed) were selected in the screening approach with Plackett-Burman experimental design, suggesting 12 trial runs, and the total number of viable bacteria was selected as the observed response to determine the effects of the variables studied [12]. To increase the response, each factor selected was tested in two levels, high levels (+1) and low levels (-1). The Plackett-Burman experiments design was formulated for six factors that affect the biomass of B. megaterium using the Design-Expert version 8.0.6 software (Stat-Ease, Inc., Minneapolis, MN, USA). The factors and levels of Plackett-Burman design shown in Table 1 were determined based on the one-factor-at-a-time experiments.

Steepest ascent design. The steepest ascent experiment was performed to move the experimental region of the response in the direction of the optimum after having identified the three most significant variables through the Plackett-Burman design [13]. The path was initiated from the design center of the factorial design (the screening design) and receded when no further improvement in the response could be achieved. When the maximum value was gained, the point could be considered as the center point for the optimization experimental design [14]. Table 2 summarizes the steepest ascent experimental design, the variables, and their values.

Box-Behnken design. The response surface methodology is a very practical and valuable tool for fermentation industry to improve product yield and minimize by‐products as well as reduce overall manufacturing costs [15], and it is possible for response surface methodology to derive an expression for performance measurement on the basis of the response values obtained from experiments at a particular combination of input variables [16]. In the present study, by employing Box-Behnken design and response surface methodology, the effects of the three independent variables (loaded liquid, mL/250mL; liquid pH, 7.0-8.0; culture temperature, °C) and three levels (high, middle, and low) on the response (the total number of living bacteria) were investigated to determine the optimal conditions, which maximized the biomass of B. megaterium from shake cultivation. The Box-Behnken design comprised 17 experiments with five center points (to allow for estimation of pure error) and facilitated calculations of response function at intermediate levels, fitting a second-order response surface. Table 3 showed the variables and their values and the experimental design.

Field experiment. The well-developed and proportioned seeds of Spinacia oleracea L. germinating on the moist and 20°C condition were selected to sow at 2 cm depth. After sprouting 5 days, the plants of S. oleracea L. were transplanted to 7 seedling plates with the same plain soil and vertically placed into the hole, two plans per hole. The 7 seeding plates of S. oleracea L. were treated with different dose of fermentation broth of B. megaterium cultured on the optimized condition. Seeding plate 1 was the control group and only treated with the same dose of water in the vegetation process. Seeding plate 2 was applied with one time of the fermentation broth after transplanting plant survived. Seeding plate 3 was, respectively, treated one time at the surviving time and during middle time of upgrowth. Seeding plate 4 was treated 3 times: the first two times were the same as seeding plate 3, and the third time came into operation at 10 days before harvest. Seeding plates 5-7 were the industrial wastewater control groups and treated with the same dose of A. bisporus industrial wastewater. Seeding plate 5 was applied one time after transplanting plant survived. Seeding plate 6 was, respectively, treated one time at the surviving time and during middle time of upgrowth. Seeding plate 7 was treated 3 times: the first two times were the same as seeding plate 6, and the third time came into operation at 10 days before harvest. The 500 mL water, A. bisporus industrial wastewater, and fermentation broth were treated with the 7 seeding plates every time, respectively. During the cultivation, watering was necessary to keep the moist of soil. After transplanting for 30 days, S. oleracea L. in the 7 seeding plates was gathered, and its plant height, yield, and leaf area were analyzed. The experiment was repeated in triplicate.

Determination of the total number of living B. megaterium. Take the fermentation broth diluted 10 times with PBS, take 1mL diluted solution plus 3μL LIVE/DEAD Baclight™ staining reagent, after mixing, avoid light for 30min, and analyze by multispectral imaging flow cytometry [17]. The PBS solution was used as a flow sheath; 480nm laser was used to collect fluorescence signals and images of 20000 bright field (BF), channel 2 green fluorescence (SYTO 9), and channel 5 red fluorescence (propidium iodide, PI); the SYTO 9 signal is the X axis, the PI signal is the Y axis, and the scatter plot is made to distinguish the total number of the dead and the statistical living bacteria.

3. Results and Discussion

3.1. The Part Results of the Total Number of Living B. megaterium in the Fermentation Liquid Analyzed by Multispectral Imaging Flow Cytometry

As shown in Figure 1, two segregated regions were identified and gated (Figure 1(a)): SYTO 9 green-fluorescent nucleic acid stain mixed with the red-fluorescent nucleic acid stain, PI; those stains differ both in their spectral characteristics and in their ability to penetrate healthy bacterial cells [18, 19]. Thus, with an appropriate mixture of the SYTO 9 and PI, bacteria with intact cell membranes stain fluorescent green (Figure 1(c)), whereas bacteria with damaged membranes stain fluorescent red (Figure 1(b)). Clearly we could score which bacteria are dead and which bacteria are alive in this assay.

(a)

(b)

(c)

Figure 1

Live and dead B. megaterium based on multispectral imaging flow. Note. (a) From the collected images, live and dead B. megaterium were visually identified (as indicated by colored crosses) and the tagged populations were gated on the original plot. (b) Images of dead B. megaterium in the fermented liquid. (c) Images of live B. megaterium in the fermented liquid. Images from within each region were chosen at random. From left to right, bright field, SYTO 9, and PI channel images are displayed.

3.2. Plackett-Burman Experiment

Plackett-Burman experimental design matrix and results are shown in Table 4 and analysis of variance is depicted in Table 5. The model F-value of 7.17 in Table 5 implies that the Plackett-Burman experimental model is significant and that there is only a 2.36% chance that a “model F-value” this large could occur due to noise. The p values of each factor in Table 5 were used to determine the significance of the screened variables; therefore, Table 5 indicated that three out of six variables, viz., liquid quantity, initial pH, and cultured temperature, had a significant influence on the total number of living bacteria. The Coefficient Estimate of variables displayed the positive or negative effect on the response value. Therefore, loaded liquid showed the highest level of significance with Coefficient Estimate of -1.07 with an F-value of 17.78 and a very low p =0.0084 < 0.01, which indicated loaded liquid had the significant positive effect on the biomass of B. megaterium. By that analogy, the initial pH exhibited significant positive effects and culture temperature exhibited significant negative effects.

3.3. Steepest Ascent Design

According to analysis of variance in Plackett-Burman design, six sets of experiments of the steepest ascent and corresponding experimental results were shown in Table 2. The biomass of B. megaterium peaked at the fifth step and no further improvement could be achieved in the response when the loaded liquid was 30 mL/250mL, the initial pH was 7.5, and the culture temperature was 28°C, which suggested that it was proximal to the region of maximum response. Accordingly, these levels of the three factors in the fifth set were considered the center point of Box-Behnken design.

3.4. Optimization of Fermentation Parameters by Response Surface Methodology

According to the result of steepest ascent design, the response surface experiments were designed to obtain a second-order polynomial equation consisting of 12 trials plus 5 central points; thus the design matrix of the variables was shown in Table 3 along with the experimental values of response. Through multiple regression analysis of the experimental data, shown in Table 6, the following second-order polynomial equation was derived for the total number of living B. megaterium by only considering the significant terms: Y=8.48-1.41X₁+0.24X₂+1.54X₃-0.73X₁X₂+0.092X₁X₃-0.097X₂X₃-2.58X₁²-2.59X₂²-2.97X₃², where Y is the predicted response of the total number of living B. megaterium and X₁, X₂, and X₃ are the coded values of loaded liquid, initial pH, and culture temperature, respectively.

A large model F-value indicates that most of the variation in the response can be explained by a given regression equation. As shown in Table 6, the F-value of model was 86.36, which indicated that the terms in the model had a significant effect on the response, and the p < 0.0001 of regression model indicated that the linear relationship between dependent variable and all independent variables was very significant; that is, the experimental method was reliable. The lack of fit for the model was insignificant (p < 0.05) with p value of 0.1964, suggesting that the experimental data obtained was a good fit with the model. The value of adj-R² (0.9796) suggested that the total variation of 97.96% for the biomass of B. megaterium was attributed to the independent variables. The determination coefficient (R²=0.9911), which is commonly used to assess the goodness of the model, exhibited an excellent correlation between the experimental and predicted response values. A low CV (CV = 9.20%) value clearly revealed that the deviations between experimental and predicted values were low and it displayed not only a high degree of precision but also high reliability in conducted experiments. Adequate precision measures the signal-to-noise ratio, and a ratio greater than 4 is desirable. In this study, a ratio of 26.229 indicated an adequate signal. Therefore, the quadratic model was selected in this optimization study.

The optimal levels of each variable for a maximum biomass of B. megaterium were determined by creating three-dimensional (3D) response surface plots. Interpretation of the response surface 3D model and contour plot were the graphical representations of regression equation. They provided visual interpretations of the relationship between responses and experimental levels of each variable, and the type of interactions between two test variables [20], as shown in Figure 2, the profiles of the response surfaces between loaded liquid (X₁) and pH (X₂) (Figure 2(a)), loaded liquid (X₁) and temperature (X₃) (Figure 2(c)), pH (X₂) and temperature (X₃) (Figure 2(e)) were all convex with an open downward direction, therefore, indicating a high total number of viable B. megaterium. When the loaded liquid (test level is 0) was 30 mL/250mL, the pH was 7.5 (test level is 0), and the culture temperature was 28°C (test level is 0); the total number of living bacteria reached the actual maximum (8.75 ± 0.04, 8.67 ± 0.03, 8.57 ± 0.03 × 10⁸ Obj/mL) closing to the design points, respectively. Furthermore, the shape of the contour plot could explain the significant interaction between two test variables. The contour line (Figure 2(b)) is oval and the interaction between load liquid and pH was significant. However, the contour line (Figures 2(d) and 2(f)) is round and the interactions between loaded liquid and temperature, pH and temperature were not significant.

(a)

(b)

(c)

(d)

(e)

(f)

Figure 2

The effect of cross-interaction among load liquid, pH, and culture temperature on total number of alive B. megaterium. Note. (a) Response surface plot of effects of interaction between load liquid and pH on total number of alive B. megaterium. (b) Contour line of effects of interaction between load liquid and pH on total number of alive B. megaterium. (c) Response surface plot of effects of interaction between load liquid and culture temperature on total number of alive B. megaterium. (d) Contour line of effects of interaction between load and culture temperature on total number of alive B. megaterium. (e) Response surface plot of effects of interaction between pH and culture temperature on total number of alive B. megaterium. (f) Contour line of effects of interaction between pH and culture temperature on total number of alive B. megaterium.

These observations were also verified through canonical analysis of the response surface. By solving the inverse matrix from the second-order polynomial equation, the optimum values of the test variables were loaded liquid 39.33 mL/250mL, pH 7.36, and temperature 25.01°C, and the predictive value of the total number of viable B. megaterium was 8.88 × 10⁸ Obj/mL. To confirm the validity of the model for predicting the maximum total number of viable B. megaterium, an additional experiment using this optimum operation conditions was performed under shake-flask culture. The total number of viable B. megaterium was 9.05 ± 0.03 × 10⁸ Obj/mL (N = 3), which was 1.02 times the predicted value, suggesting that the model was adequate for reflecting the expected optimization, and the response surface methodology model was satisfactory and accurate.

3.5. Field Experiment

As shown in Table 7, the plant height, yield, and leaf area of S. oleracea L. were significantly improved as the times that S. oleracea L. was treaded with the fermentation liquid of B. megaterium using A. bisporus industrial wastewater as culture increased. Although the yield of S. oleracea in the A. bisporus industrial wastewater control group was significant compared with the control group, plant height, yield, and leaf area in groups treated with fermentation broth of B. megaterium were more conspicuously increasing. As shown in Figure 3, the grown status of S. oleracea L. in Figure 3(c) which was treated with fermentation broth of B. megaterium 3 times was the best in all the plates.

(a)

(b)

(c)

(d)

(e)

(f)

(g)

Response surface methodology is one more effective method that reduced development costs, optimized experimental conditions, improved production efficiency, and solved practical production problems. Compared with one-factor-at-a-time experiments, statistically designed experiments are able to describe the effect of the interactions among the factors in linear and quadratic terms [21]. In the present study, the optimization of fermentation conditions for B. megaterium was divided into two phases: a screening of main effects of the selected variables and a response optimization. Reduction in the initial number of variables was carried out through Plackett-Burman design that was used to screen out three factors from six factors (industrial wastewater solubility, initial pH, inoculum dose, loaded liquid, culture temperature, and shaking speed) affecting the total number of viable bacteria as major factor, which were the loaded liquid, initial pH, and culture temperature which were taken for Box-Behnken design of response surface methodology to assess their effects on the biomass of B. megaterium. We used response surface methodology to further optimize the biomass of B. megaterium by Box-Behnken design. Response surface methodology not only helped locate the optimum levels of the most significant factors but also proved to be useful and satisfactory in this process-optimizing practice. Through these optimization experiments, the maximum biomass of B. megaterium at 9.05 ± 0.03 × 10⁸ Obj/mL was obtained under the optimum conditions with speed 200 rmp, precooking liquid solubility 1%, temperature 25°C, initial pH 7.4, and inoculum 8%, liquid volume 40 mL/250mL, after 24 hours.

In conclusion, the effect of loaded liquid, pH, and incubation temperature and interactions between these factors all had a significant effect on the total number of viable B. megaterium. After optimization of the response surface, the optimum conditions for the fermentation of B. megaterium using A. bisporus wastewater were determined to be a liquid volume of 40 mL/250 mL, pH of 7.4, temperature of 25°C, precooking liquid solubility of 1%, inoculum volume of 8%, shaking speed of 200 rpm, and culture time of 24 h. Under these conditions, the total number of living bacteria can reach 9.05 ± 0.02 × 10⁸ Obj/mL, satisfying the national standard (GB 20287-2006). Furthermore, the fermentation broth of B. megaterium could significantly improve the yield of Spinacia oleracea L.

Data Availability

The data used to support the findings of this study are included within the article. The detailed original data are available upon request from the corresponding author.

Conflicts of Interest

The authors declare no conflicts of interest.

Acknowledgments

This study was funded by the Fujian Provincial Department of Science and Technology (No. 2015N0030), the Key Natural Fund Project of the University Youth of Fujian Province (No. JZ160454), Natural Science Fund Project of Fujian Province (No. 2016J05083 and No. 2015J01144), Program for New Century Excellent Talents in Minnan Normal University (No. MX13004), and the Young Teacher Project of Fujian Provincial Department of Education (No. JT180297).

References

S. Mukhtar, I. Shahid, S. Mehnaz, and K. A. Malik, “Assessment of two carrier materials for phosphate solubilizing biofertilizers and their effect on growth of wheat (Triticum aestivum L.),” Microbiological Research, vol. 205, pp. 107–117, 2017.
View at: Publisher Site | Google Scholar
N.-X. Feng, J. Yu, C.-H. Mo et al., “Biodegradation of di-n-butyl phthalate (DBP) by a novel endophytic Bacillus megaterium strain YJB3,” Science of the Total Environment, vol. 616-617, pp. 117–127, 2018.
View at: Publisher Site | Google Scholar
F. Feng, J. Ge, Y. Li et al., “Enhanced degradation of chlorpyrifos in rice (Oryza sativa L.) by five strains of endophytic bacteria and their plant growth promotional ability,” Chemosphere, vol. 184, pp. 505–513, 2017.
View at: Publisher Site | Google Scholar
Y. Li, H.-D. Pang, L.-Y. He, Q. Wang, and X.-F. Sheng, “Cd immobilization and reduced tissue Cd accumulation of rice (Oryza sativa wuyun-23) in the presence of heavy metal-resistant bacteria,” Ecotoxicology and Environmental Safety, vol. 138, pp. 56–63, 2017.
View at: Publisher Site | Google Scholar
P. Ibort, H. Imai, M. Uemura, and R. Aroca, “Proteomic analysis reveals that tomato interaction with plant growth promoting bacteria is highly determined by ethylene perception,” Journal of Plant Physiology, vol. 220, pp. 43–59, 2018.
View at: Publisher Site | Google Scholar
Q. Wang, W.-J. Zhang, L.-Y. He, and X.-F. Sheng, “Increased biomass and quality and reduced heavy metal accumulation of edible tissues of vegetables in the presence of Cd-tolerant and immobilizing Bacillus megaterium H3,” Ecotoxicology and Environmental Safety, vol. 148, pp. 269–274, 2018.
View at: Publisher Site | Google Scholar
J. F. Huang, Y. X. Ou, T. W. D. Yew et al., “Hepatoprotective effects of polysaccharide isolated from Agaricus bisporus industrial wastewater against CCl4-induced hepatic injury in mice,” International Journal of Biological Macromolecules, vol. 82, pp. 678–686, 2016.
View at: Publisher Site | Google Scholar
J. M. Lin, J. F. Huang, and J. Y. Chen, “Low cytotoxic d-mannitol isolated from the industrial wastewater of Agaricus bisporus,” Journal of Food and Nutrition Research, vol. 4, no. 9, pp. 610–614, 2016.
View at: Google Scholar
J. F. Huang, Y. X. Ou, D. D. Zhang, G. G. Zhang, and Y. T. Pan, “Optimization of the culture condition of Bacillus mucilaginous using Agaricus bisporus industrial wastewater by Plackett–Burman combined with Box–Behnken response surface method,” AMB Express, vol. 8, no. 1, 2018.
View at: Publisher Site | Google Scholar
X. R. Zhan, J. F. Huang, and J. M. Chen, “Optimization of tissue culture medium of Anoectochilus roxburghii using liquid of the mushroom precooking process (LMPP,” Journal of Minnan Normol University, vol. 2, pp. 57–64, 2017.
View at: Google Scholar
A. K. Sahu and V. Jain, “Screening of process variables using Plackett–Burman design in the fabrication of gedunin-loaded liposomes,” Artificial Cells, Nanomedicine and Biotechnology, vol. 45, no. 5, pp. 1011–1022, 2016.
View at: Publisher Site | Google Scholar
M. G. Ekpenyong, S. P. Antai, A. D. Asitok, and B. O. Ekpo, “Plackett-burman design and response surface optimization of medium trace nutrients for glycolipopeptide biosurfactant production,” Iranian Biomedical Journal, vol. 21, no. 4, pp. 249–260, 2017.
View at: Publisher Site | Google Scholar
B. yingling, Y. zhengfang, and R. P. Niedz, “Application of an integrated statistical design for optimization of culture condition for ammonium removal by Nitrosomonas europaea,” PLoS ONE, vol. 8, no. 4, p. e60322, 2013.
View at: Publisher Site | Google Scholar
H. Chen, J. Niu, T. Qin, Q. Ma, L. Wang, and G. Shu, “Optimization of the medium for Lactobacillus acidophilus by Plackett-Burman and steepest ascent experiment,” ACTA Scientiarum Polonorum Technologia Alimentaria, vol. 14, no. 3, pp. 227–232, 2015.
View at: Publisher Site | Google Scholar
F. Guo, H. Zheng, and Y. Cheng, “Medium optimization for epsilon-poly-L-lysine production by Streptomyces diastatochromogenes using response surface methodology,” Letters in Applied Microbiology, vol. 66, no. 2, pp. 124–131, 2018.
View at: Publisher Site | Google Scholar
K. Wu, L. Ding, P. Zhu, S. Li, and S. He, “Application of the response surface methodology to optimize the fermentation parameters for enhanced docosahexaenoic acid (DHA) production by Thraustochytrium sp. ATCC 26185,” Molecules, vol. 23, no. 4, p. 974, 2018.
View at: Publisher Site | Google Scholar
M. E. K. Calvert, J. A. Lannigan, and L. F. Pemberton, “Optimization of yeast cell cycle analysis and morphological characterization by multispectral imaging flow cytometry,” Cytometry Part A, vol. 73, no. 9, pp. 825–833, 2008.
View at: Publisher Site | Google Scholar
W. Hu, K. Murata, and D. Zhang, “Applicability of LIVE/DEAD BacLight stain with glutaraldehyde fixation for the measurement of bacterial abundance and viability in rainwater,” Journal of Environmental Sciences, vol. 51, pp. 202–213, 2017.
View at: Publisher Site | Google Scholar
M. Berney, F. Hammes, F. Bosshard, H.-U. Weilenmann, and T. Egli, “Assessment and interpretation of bacterial viability by using the LIVE/DEAD BacLight kit in combination with flow cytometry,” Applied and Environmental Microbiology, vol. 73, no. 10, pp. 3283–3290, 2007.
View at: Publisher Site | Google Scholar
J. Long, X. Zhao, F. Liang, N. Liu, Y. Sun, and Y. Xi, “Optimization of fermentation conditions for an Escherichia coli strain engineered using the response surface method to produce a novel therapeutic DNA vaccine for rheumatoid arthritis,” Journal of Biological Engineering, vol. 12, no. 1, 2018.
View at: Publisher Site | Google Scholar
A. N. Rane, V. V. Baikar, V. Ravi Kumar et al., “Agro-industrial wastes for production of biosurfactant by Bacillus subtilis ANR 88 and its ppplication in synthesis of silver and gold nanoparticles,” Frontiers in Microbiology, vol. 8, p. 492, 2017.
View at: Google Scholar

Copyright

Copyright © 2018 Jiafu Huang et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

3595

Downloads

1413

Citations