Advances in Tribology

Tribological and Mechanical Properties of Gradient Coating on Al₂O₃-Based Coating Produced by Detonation Spraying Methods

Investigation on the Cutting Force and Surface Quality in Harmonically Vibrated Broaching (HVB)

Influence of Spraying Parameters on the Structure and Tribological Properties of Cr₃C₂-NiCr Detonation Coatings

Assessment of the Conventional Acid-Clay Method in Reclaiming Waste Crankcase Lubricating Oil

Dynamic Processes of Self-Organization in Nonstationary Conditions of Friction

Tribological Behavior of Mild Steel under Canola Biolubricant Conditions

Tribological Behavior of Ni-Based WC-Co Coatings Deposited via Spray and Fuse Technique Varying the Oxygen Flow

Computer Simulation/Prediction of Wear in Mechanical Components

Experimental and Numerical Investigation about Small Clearance Journal Bearings under Static Load Conditions

Experimental and Molecular Level Analysis of the Tribological and Oxidative Properties of Chaulmoogra Oil

Experimental Investigation of the Diagnosis of Angular Contact Ball Bearings Using Acoustic Emission Method and Empirical Mode Decomposition

Tribological Behavior of Tool Steel Substrate and Solid Films against 304 BA Austenitic Stainless Steel under Dry Sliding

Effect of Load on the Tribological Properties of Eutectic Al-Si Reinforced n-Al₂O₃ under Dry Sliding Conditions

Estimation of the Oxidative Deterioration of Turbine Oil Using Membrane Patch Color

The Performance of Squeeze Film between Parallel Triangular Plates with a Ferro-Fluid Couple Stress Lubricant

Advances in Tribology

Table of Contents

Table of Contents

Tribological and Mechanical Properties of Gradient Coating on Al₂O₃-Based Coating Produced by Detonation Spraying Methods

Investigation on the Cutting Force and Surface Quality in Harmonically Vibrated Broaching (HVB)

Influence of Spraying Parameters on the Structure and Tribological Properties of Cr₃C₂-NiCr Detonation Coatings

Assessment of the Conventional Acid-Clay Method in Reclaiming Waste Crankcase Lubricating Oil

Dynamic Processes of Self-Organization in Nonstationary Conditions of Friction

Tribological Behavior of Mild Steel under Canola Biolubricant Conditions

Tribological Behavior of Ni-Based WC-Co Coatings Deposited via Spray and Fuse Technique Varying the Oxygen Flow

Computer Simulation/Prediction of Wear in Mechanical Components

Experimental and Numerical Investigation about Small Clearance Journal Bearings under Static Load Conditions

Experimental and Molecular Level Analysis of the Tribological and Oxidative Properties of Chaulmoogra Oil

Experimental Investigation of the Diagnosis of Angular Contact Ball Bearings Using Acoustic Emission Method and Empirical Mode Decomposition

Tribological Behavior of Tool Steel Substrate and Solid Films against 304 BA Austenitic Stainless Steel under Dry Sliding

Effect of Load on the Tribological Properties of Eutectic Al-Si Reinforced n-Al₂O₃ under Dry Sliding Conditions

Estimation of the Oxidative Deterioration of Turbine Oil Using Membrane Patch Color

The Performance of Squeeze Film between Parallel Triangular Plates with a Ferro-Fluid Couple Stress Lubricant

Advances in Tribology

Table of Contents

Table of Contents

Tribological and Mechanical Properties of Gradient Coating on Al2O3-Based Coating Produced by Detonation Spraying Methods

Investigation on the Cutting Force and Surface Quality in Harmonically Vibrated Broaching (HVB)

Influence of Spraying Parameters on the Structure and Tribological Properties of Cr3C2-NiCr Detonation Coatings

Assessment of the Conventional Acid-Clay Method in Reclaiming Waste Crankcase Lubricating Oil

Dynamic Processes of Self-Organization in Nonstationary Conditions of Friction

Tribological Behavior of Mild Steel under Canola Biolubricant Conditions

Tribological Behavior of Ni-Based WC-Co Coatings Deposited via Spray and Fuse Technique Varying the Oxygen Flow

Computer Simulation/Prediction of Wear in Mechanical Components

Experimental and Numerical Investigation about Small Clearance Journal Bearings under Static Load Conditions

Experimental and Molecular Level Analysis of the Tribological and Oxidative Properties of Chaulmoogra Oil

Experimental Investigation of the Diagnosis of Angular Contact Ball Bearings Using Acoustic Emission Method and Empirical Mode Decomposition

Tribological Behavior of Tool Steel Substrate and Solid Films against 304 BA Austenitic Stainless Steel under Dry Sliding

Effect of Load on the Tribological Properties of Eutectic Al-Si Reinforced n-Al2O3 under Dry Sliding Conditions

Estimation of the Oxidative Deterioration of Turbine Oil Using Membrane Patch Color

The Performance of Squeeze Film between Parallel Triangular Plates with a Ferro-Fluid Couple Stress Lubricant

Tribological and Mechanical Properties of Gradient Coating on Al₂O₃-Based Coating Produced by Detonation Spraying Methods

Influence of Spraying Parameters on the Structure and Tribological Properties of Cr₃C₂-NiCr Detonation Coatings

Effect of Load on the Tribological Properties of Eutectic Al-Si Reinforced n-Al₂O₃ under Dry Sliding Conditions