International Journal of Rotating Machinery

Table of Contents: 2008

  • International Journal of Rotating Machinery -
  • Special Issue
  • Volume 2008
  • - Article ID 273296
  • - Research Article

Off-Design Considerations through the Properties of Some Pressure-Ratio Line of Radial Inflow Turbines

N. Binder | X. Carbonneau | P. Chassaing
  • International Journal of Rotating Machinery -
  • Special Issue
  • Volume 2008
  • - Article ID 146234
  • - Research Article

Influence of the Cavitation Model on the Simulation of Cloud Cavitation on 2D Foil Section

S. Frikha | O. Coutier-Delgosha | J. A. Astolfi
  • International Journal of Rotating Machinery -
  • Special Issue
  • Volume 2008
  • - Article ID 635138
  • - Research Article

Turbulence Modeling of Torsional Couette Flows

Sofia Haddadi | Sébastien Poncet
  • International Journal of Rotating Machinery -
  • Special Issue
  • Volume 2008
  • - Article ID 109120
  • - Research Article

Experimental Investigation of Innovative Internal Trailing Edge Cooling Configurations with Pentagonal Arrangement and Elliptic Pin Fin

L. Tarchi | B. Facchini | S. Zecchi
  • International Journal of Rotating Machinery -
  • Special Issue
  • Volume 2008
  • - Article ID 719510
  • - Research Article

On the Flow Behavior in Rotor-Stator System with Superposed Flow

Roger Debuchy | Fadi Abdel Nour | Gérard Bois
  • International Journal of Rotating Machinery -
  • Special Issue
  • Volume 2008
  • - Article ID 354020
  • - Research Article

Cavitation in Single-Vane Sewage Pumps

P. U. Thamsen | T. Bubelach | ... | P. Springer
  • International Journal of Rotating Machinery -
  • Special Issue
  • Volume 2008
  • - Article ID 657202
  • - Research Article

Simulation of Casing Treatments of a Transonic Compressor Stage

M. Hembera | H.-P. Kau | E. Johann
  • International Journal of Rotating Machinery -
  • Special Issue
  • Volume 2008
  • - Article ID 764720
  • - Research Article

Effects of Centrifugal Buoyancy and Reynolds Number on Turbulent Heat Transfer in a Two-Pass Angled-RIB-Roughened Channel with Sharp 180° Turns Investigated by Using Large Eddy Simulation

Akira Murata | Sadanari Mochizuki
  • International Journal of Rotating Machinery -
  • Special Issue
  • Volume 2008
  • - Article ID 536079
  • - Research Article

Quasi-Steady Analytical Model Benchmark of an Impulse Turbine for Wave Energy Extraction

A. Thakker | J. Jarvis | A. Sahed
  • International Journal of Rotating Machinery -
  • Special Issue
  • Volume 2008
  • - Article ID 202179
  • - Research Article

Time-Frequency Characterization of Rotating Instabilities in a Centrifugal Pump with a Vaned Diffuser

G. Pavesi | G. Cavazzini | G. Ardizzon
  • International Journal of Rotating Machinery -
  • Special Issue
  • Volume 2008
  • - Article ID 737285
  • - Research Article

Observation and Analysis of Affinity Law Deviations through Tested Performance of Liquefied Gas Reaction Turbines

Sarah D. Alison-Youel
  • International Journal of Rotating Machinery -
  • Special Issue
  • Volume 2008
  • - Article ID 218978
  • - Research Article

Interaction between Uneven Cavity Length and Shaft Vibration at the Inception of Synchronous Rotating Cavitation

Y. Yoshida | Y. Kazami | ... | T. Ikohagi
  • International Journal of Rotating Machinery -
  • Special Issue
  • Volume 2008
  • - Article ID 175956
  • - Research Article

Possibilities of Simultaneous In-Cylinder Reduction of Soot and Emissions for Diesel Engines with Direct Injection

U. Wagner | P. Eckert | U. Spicher
  • International Journal of Rotating Machinery -
  • Special Issue
  • Volume 2008
  • - Article ID 784749
  • - Research Article

The Fisher Information Matrix as a Relevant Tool for Sensor Selection in Engine Health Monitoring

S. Borguet | O. Léonard
  • International Journal of Rotating Machinery -
  • Special Issue
  • Volume 2008
  • - Article ID 125678
  • - Research Article

Theoretical Analysis of Thermodynamic Effect of Cavitation in Cryogenic Inducer Using Singularity Method

S. Watanabe | A. Furukawa | Y. Yoshida
International Journal of Rotating Machinery
 Journal metrics
Acceptance rate27%
Submission to final decision75 days
Acceptance to publication42 days
CiteScore2.100
Impact Factor-
 Submit

We are committed to sharing findings related to COVID-19 as quickly as possible. We will be providing unlimited waivers of publication charges for accepted research articles as well as case reports and case series related to COVID-19. Review articles are excluded from this waiver policy. Sign up here as a reviewer to help fast-track new submissions.